Document Center List of Standards on Ventilation And Air-Conditioning Systems Including Ventilation Ducts Ventilators And Air-Conditioners, See 23.120
ICS Code 91.140.30
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
ASTM:
- ASTM-C1003 - Test Method for Thermal Performance of Cooling-Air Duct Sections, Using a Calibrated Hot Box (Withdrawn 1997)
- ASTM-C1668 - Standard Specification for Externally Applied Reflective Insulation Systems on Rigid Duct in Heating, Ventilation, and Air Conditioning (HVAC) Systems
- ASTM-C971 - Guide for Selection and Application of Insulation Systems for Heating, Ventilating, and Air Conditioning Duct Work (Withdrawn 1997)
- ASTM-D5032 - Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Glycerin Solutions
- ASTM-D8039 - Standard Specification for Heat Transfer Fluids (HTF) for Heating and Air Conditioning (HVAC) Systems
- ASTM-E2320 - Standard Classification for Serviceability of an Office Facility for Thermal Environment and Indoor Air Conditions
- ASTM-E2816 - Standard Test Methods for Fire Resistive Metallic HVAC Duct Systems
- ASTM-E2886 - Standard Test Method for Evaluating the Ability of Exterior Vents to Resist the Entry of Embers and Direct Flame Impingement
- ASTM-E779 - Standard Test Method for Determining Air Leakage Rate by Fan Pressurization
- ASTM-F1005 - Standard Practice for HVAC Duct Shapes; Identification and Description of Design Configuration
- ASTM-F1040 - Standard Specification for Filter Units, Air Conditioning: Viscous-Impingement and Dry Types, Replaceable (Withdrawn 2012)
- ASTM-F1690 - Standard Specification for Humidifiers for Medical Use—Part 1: General Requirements for Active Humidification Systems (Withdrawn 2013)
- ASTM-F1704 - Standard Test Method for Capture and Containment Performance of Commercial Kitchen Exhaust Ventilation Systems
- ASTM-F2934 - Standard Specification for Circular Metallic Bellows Type Expansion Joint for HVAC Piping Applications
- ASTM-F2975 - Standard Test Method for Measuring the Field Performance of Commercial Kitchen Ventilation Systems
- ASTM-F2976 - Standard Practice for Determining the Field Performance of Commercial Kitchen Demand Control Ventilation Systems
- ASTM-F856 - Standard Practice for Mechanical Symbols, Shipboard—Heating, Ventilation, and Air Conditioning (HVAC)
- ASTM-F872 - Specification for Filter Units, Air Conditioning: Viscous-Impingement Type, Cleanable (Withdrawn 1999)
BSI:
- BS-3456-202.139 - Specification for safety of household and similar electrical appliances. Particular requirements. Room humidifiers
- BS-3456-2-2.39 - Specification for safety of household and similar electrical appliances. Particular requirements
- BS-416-1 - Discharge and ventilating pipes and fittings, sand-cast or spun in cast iron
- BS-4718 - Methods of test for silencers for air distribution systems
- BS-4773-1.1 - Methods for testing and rating air terminal devices for air distribution systems. Aerodynamic testing. Testing under laboratory conditions
- BS-4856-1 - Methods for testing and rating fan coil units, unit heaters and unit coolers
- BS-4856-2 - Methods for testing and rating fan coil units, unit heaters and unit coolers
- BS-4856-3 - Methods for testing and rating fan coil units, unit heaters and unit coolers
- BS-4856-4 - Methods for testing and rating fan coil units, unit heaters and unit coolers
- BS-4857-1 - Methods for testing and rating terminal reheat units for air distribution systems
- BS-4857-2 - Methods for testing and rating terminal reheat units for air distribution systems
- BS-4954-1 - Methods for testing and rating induction units for air distribution systems
- BS-4954-2 - Methods for testing and rating induction units for air distribution systems
- BS-4979 - Methods for aerodynamic testing of constant and variable dual or single duct boxes, single duct units and induction boxes for air distribution systems.
- BS-5141-1 - Specification for air heating and cooling coils
- BS-5502-52 - Buildings and structures for agriculture
- BS-5588-9 - Fire Precautions in the Design, Construction & Use of Buildings, Code of Practice For
- BS-5601-2 - Code of practice for ventilation and heating of caravans
- BS-5720 - Code of Practice for Mechanical Ventilation & Air Conditioning in Buildings (Formerly Cp 3
- BS-5925 - Code of practice for ventilation principles and designing for natural ventilation
- BS-6762-2 - Services for leisure accommodation vehicles and transportable accommodation units
- BS-7074-3 - Application, selection and installation of expansion vessels and ancillary equipment for sealed water systems
- BS-7120 - Specification for rating and performance of air to liquid and liquid to liquid chilling packages
- BS-7346-8 - Components for smoke control systems
- BS-7989 - Specification for recirculatory filtration fume cupboards
- BS-EN-12097 - Ventilation for buildings. Requirements for ductwork components to facilitate maintenance of ductwork systems
- BS-EN-12102 - Air conditioners, liquid chilling packages, heat pumps and dehumidifiers with electrically driven compressors for space heating and cooling. Measurement of airborne noise. Determination of the sound power level
- BS-EN-12102-1 - Air conditioners, liquid chilling packages, heat pumps, process chillers and dehumidifiers with electrically driven compressors. Determination of the sound power level
- BS-EN-12220 - Ventilation for buildings. Ductwork. Dimensions of circular flanges for general ventilation
- BS-EN-12236 - Ventilation for buildings. Ductwork hangers and supports. Requirements for strength
- BS-EN-12238 - Ventilation for buildings. Air terminal devices. Aerodynamic testing and rating for mixed flow application
- BS-EN-12239 - Ventilation for buildings. Air terminal devices. Aerodynamic testing and rating for displacement flow applications
- BS-EN-12309-1 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW
- BS-EN-12309-2 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW
- BS-EN-12309-3 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW
- BS-EN-12309-4 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW
- BS-EN-12309-5 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW
- BS-EN-12309-6 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW
- BS-EN-12309-7 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW
- BS-EN-12589 - Ventilation for buildings. Air terminal units. Aerodynamic testing and rating of constant and variable rate terminal units
- BS-EN-12599 - Ventilation for buildings. Test procedures and measurement methods to hand over air conditioning and ventilation systems
- BS-EN-12735-1 - Copper and copper alloys. Seamless, round tubes for air conditioning and refrigeration
- BS-EN-12735-2 - Copper and copper alloys. Seamless, round tubes for air conditioning and refrigeration
- BS-EN-12735-2-TC - Tracked Changes. Copper and copper alloys. Seamless, round tubes for air conditioning and refrigeration
- BS-EN-13030 - Ventilation for buildings. Terminals. Performance testing of louvres subjected to simulated rain
- BS-EN-13053 - Ventilation for buildings. Air handling units. Rating and performance for units, components and sections
- BS-EN-13141-10 - Ventilation for buildings. Performance testing of components/products for residential ventilation
- BS-EN-13141-11 - Ventilation for buildings. Performance testing of components/products for residential ventilation
- BS-EN-13141-3 - Ventilation for buildings. Performance testing of components/products for residential ventilation
- BS-EN-13141-3-TC - Tracked Changes. Ventilation for buildings. Performance testing of components/products for residential ventilation
- BS-EN-13141-4 - Ventilation for buildings. Performance testing of components/products for residential ventilation
- BS-EN-13141-4-TC - Tracked Changes. Ventilation for buildings. Performance testing of components/products for residential ventilation
- BS-EN-13141-5 - Ventilation for buildings. Performance testing of components/products for residential ventilation
- BS-EN-13141-6 - Ventilation for buildings. Performance testing of components/products for residential ventilation
- BS-EN-13141-7 - Ventilation for buildings. Performance testing of components/products for residential ventilation
- BS-EN-13141-8 - Ventilation for buildings. Performance testing of components/products for residential ventilation
- BS-EN-13141-8-TC - Tracked Changes. Ventilation for buildings. Performance testing of components/products for residential ventilation
- BS-EN-13141-9 - Ventilation for buildings. Performance testing of components/products for residential ventilation
- BS-EN-13142 - Ventilation for buildings. Components/products for residential ventilation. Required and optional performance characteristics
- BS-EN-13142-TC - Tracked Changes. Ventilation for buildings. Components/products for residential ventilation. Required and optional performance characteristics
- BS-EN-13180 - Ventilation for buildings. Ductwork. Dimensions and mechanical requirements for flexible ducts
- BS-EN-13181 - Ventilation for buildings. Terminals. Performance testing of louvres. Performance testing of louvres subject to simulated sand
- BS-EN-13182 - Ventilation for buildings. Instrumentation requirements for air velocity measurements in ventilated spaces
- BS-EN-13264 - Ventilation for buildings. Floor mounted air terminal devices. Tests for structural classification
- BS-EN-13403 - Ventilation for buildings. Non metallic ducts. Ductwork made from insulation ductboards
- BS-EN-13410 - Gas-fired overhead radiant heaters. Ventilation requirements for non-domestic premises
- BS-EN-13465 - Ventilation for buildings. Calculation methods for the determination of air flow rates in dwellings
- BS-EN-1366-10-TC - Tracked Changes. Fire resistance tests for service installations.
- BS-EN-13779 - Ventilation for non-residential buildings. Performance requirements for ventilation and room-conditioning systems
- BS-EN-14037-4 - Free hanging heating and cooling surfaces for water with a temperature below 120C
- BS-EN-14277 - Ventilation for buildings. Air terminal devices. Method for airflow measurement by calibrated sensors in or close to ATD/plenum boxes
- BS-EN-14511-1 - Air conditioners, liquid chilling packages and heat pumps for space heating and cooling and process chillers, with electrically driven compressors
- BS-EN-14511-1-TC - Tracked Changes. Air conditioners, liquid chilling packages and heat pumps for space heating and cooling and process chillers, with electrically driven compressors
- BS-EN-14511-2 - Air conditioners, liquid chilling packages and heat pumps for space heating and cooling and process chillers, with electrically driven compressors
- BS-EN-14511-2-TC - Tracked Changes. Air conditioners, liquid chilling packages and heat pumps for space heating and cooling and process chillers, with electrically driven compressors
- BS-EN-14511-3 - Air conditioners, liquid chilling packages and heat pumps for space heating and cooling and process chillers, with electrically driven compressors
- BS-EN-14511-3-TC - Tracked Changes. Air conditioners, liquid chilling packages and heat pumps for space heating and cooling and process chillers, with electrically driven compressors
- BS-EN-14511-4 - Air conditioners, liquid chilling packages and heat pumps for space heating and cooling and process chillers, with electrically driven compressors
- BS-EN-14511-4-TC - Tracked Changes. Air conditioners, liquid chilling packages and heat pumps for space heating and cooling and process chillers, with electrically driven compressors
- BS-EN-14518 - Ventilation for buildings. Chilled beams. Testing and rating of passive chilled beams
- BS-EN-14825 - Air conditioners, liquid chilling packages and heat pumps, with electrically driven compressors, for space heating and cooling, commercial and process cooling. Testing and rating at part load conditions and calculation of seasonal performance
- BS-EN-14825-TC - Tracked Changes. Air conditioners, liquid chilling packages and heat pumps, with electrically driven compressors, for space heating and cooling. Testing and rating at part load conditions and calculation of seasonal performance
- BS-EN-14989-2 - Chimneys. Requirements and test methods for metal chimneys and material independent air supply ducts for roomsealed heating applications
- BS-EN-1506 - Ventilation for buildings. Sheet metal air ducts and fittings with circular cross-section. Dimensions
- BS-EN-1507 - Ventilation for buildings. Sheet metal air ducts with rectangular section. Requirements for strength and leakage
- BS-EN-15218 - Air conditioners and liquid chilling packages with evaporatively cooled condenser and with electrically driven compressors for space cooling. Terms, definitions, test conditions, test methods and requirements
- BS-EN-15218-TC - Tracked Changes. Air conditioners and liquid chilling packages with evaporatively cooled condenser and with electrically driven compressors for space cooling. Terms, definitions, test conditions, test methods and requirements
- BS-EN-15239 - Ventilation for buildings. Energy performance of buildings. Guidelines for inspection of ventilation systems
- BS-EN-15240 - Ventilation for buildings. Energy performance of buildings. Guidelines for inspection of air-conditioning systems
- BS-EN-15241 - Ventilation for buildings. Calculation methods for energy losses due to ventilation and infiltration in buildings
- BS-EN-15242 - Ventilation for buildings. Calculation methods for the determination of air flow rates in buildings including infiltration
- BS-EN-15243 - Ventilation for buildings. Calculation of room temperatures and of load and energy for buildings with room conditioning systems
- BS-EN-15316-3 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15316-4-5 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15316-4-5-TC - Tracked Changes. Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- BS-EN-15377-1 - Heating systems in buildings. Design of embedded water based surface heating and cooling systems. Determination of the design heating and cooling capacity
- BS-EN-15377-2 - Heating Systems in Buildings, Design of Embedded Water Based Surface Heating & Cooling
- BS-EN-15423 - Ventilation for buildings. Fire precaution for air distribution systems in buildings
- BS-EN-15500-1 - Energy Performance of Buildings. Control for heating, ventilating and air conditioning applications
- BS-EN-15500-1-TC - Tracked Changes. Energy Performance of Buildings. Control for heating, ventilating and air conditioning applications
- BS-EN-15650 - Ventilation for buildings. Fire dampers
- BS-EN-15665 - Ventilation for buildings. Determining performance criteria for residential ventilation systems
- BS-EN-15726 - Ventilation for buildings. Air diffusion. Measurements in the occupied zone of air-conditioned/ventilated rooms to evaluate thermal and acoustic conditions
- BS-EN-15727 - Ventilation for buildings. Ducts and ductwork components, leakage classification and testing
- BS-EN-15780 - Ventilation for buildings. Ductwork. Cleanliness of ventilation systems
- BS-EN-15805 - Particulate air filters for general ventilation. Standardised dimensions
- BS-EN-15882-1 - Extended application of results from fire resistance tests for service installations
- BS-EN-16211 - Ventilation for buildings. Measurement of air flows on site. Methods
- BS-EN-16445 - Ventilation for buildings. Air diffusion. Aerodynamic testing and rating for mixed flow application: non-isothermal procedure for cold jet
- BS-EN-16573 - Ventilation for Buildings. Performance testing of components for residential buildings. Multifunctional balanced ventilation units for single family dwellings, including heat pumps
- BS-EN-16798-13 - Energy performance of buildings. Ventilation for buildings
- BS-EN-16798-15 - Energy performance of buildings. Ventilation for buildings
- BS-EN-16798-17 - Energy performance of buildings. Ventilation for buildings
- BS-EN-16798-3 - Energy performance of buildings. Ventilation for buildings
- BS-EN-16798-3-TC - Tracked Changes. Energy performance of buildings. Ventilation for buildings
- BS-EN-16798-5-1 - Energy performance of buildings. Ventilation for buildings
- BS-EN-16798-5-2 - Energy performance of buildings. Ventilation for buildings
- BS-EN-16798-7 - Energy performance of buildings. Ventilation for buildings
- BS-EN-16798-7-TC - Tracked Changes. Energy performance of buildings. Ventilation for buildings
- BS-EN-16798-9 - Energy performance of buildings. Ventilation for buildings
- BS-EN-17088 - Side curtain ventilation systems. Safety
- BS-EN-17192 - Ventilation for buildings. Ductwork. Non-metallic ductwork. Requirements and test methods
- BS-EN-1751 - Ventilation for buildings. Air terminal devices. Aerodynamic testing of damper and valves
- BS-EN-1886 - Ventilation for buildings. Air handling units. Mechanical performance
- BS-EN-60335-2-88 - Specification for safety of household and similar electrical appliances. Particular requirements
- BS-EN-779 - Particulate air filters for general ventilation. Determination of the filtration performance
- BS-EN-810 - Dehumidifiers with electrically driven compressors. Rating tests, marking, operational requirements and technical data sheet
- BS-EN-814-3 - Air conditioners and heat pumps with electrically driven compressors. Cooling modeRequirements
- BS-EN-ISO-10121-1 - Test method for assessing the performance of gas-phase air cleaning media and devices for general ventilation
- BS-EN-ISO-10121-3 - Test methods for assessing the performance of gas-phase air cleaning media and devices for general ventilation
- BS-EN-ISO-11691 - Acoustics. Measurement of insertion loss of ducted silencers without flow. Laboratory survey method
- BS-EN-ISO-11855-1 - Building environment design. Embedded radiant heating and cooling systems
- BS-EN-ISO-11855-1-TC - Tracked Changes. Building environment design. Embedded radiant heating and cooling systems
- BS-EN-ISO-11855-2 - Building environment design. Embedded radiant heating and cooling systems
- BS-EN-ISO-11855-3 - Building environment design. Embedded radiant heating and cooling systems
- BS-EN-ISO-11855-5 - Building environment design. Embedded radiant heating and cooling systems
- BS-EN-ISO-11855-5-TC - Tracked Changes. Building environment design. Embedded radiant heating and cooling systems
- BS-EN-ISO-15858 - UV-C Devices. Safety information. Permissible human exposure
- BS-EN-ISO-15957 - Test dusts for evaluating air cleaning equipment
- BS-EN-ISO-16170 - In situ test methods for high efficiency filter systems in industrial facilities
- BS-EN-ISO-16890-1 - Air filters for general ventilation
- BS-EN-ISO-16890-2 - Air filters for general ventilation
- BS-EN-ISO-16890-2-TC - Tracked Changes. Air filters for general ventilation
- BS-EN-ISO-16890-3 - Air filters for general ventilation
- BS-EN-ISO-16890-4 - Air filters for general ventilation
- BS-EN-ISO-16890-4-TC - Tracked Changes. Air filters for general ventilation
- BS-EN-ISO-16891 - Test methods for evaluating degradation of characteristics of cleanable filter media
- BS-EN-ISO-21083-1 - Test method to measure the efficiency of air filtration media against spherical nanomaterials
- BS-EN-ISO-21805 - Guidance and recommendations on design, selection and installation of vents to safeguard the structural integrity of enclosures protected by gaseous fire-extinguishing systems
- BS-EN-ISO-29462 - Field testing of general ventilation filtration devices and systems for in situ removal efficiency by particle size and resistance to airflow
- BS-EN-ISO-29462-TC - Tracked Changes. Field testing of general ventilation filtration devices and systems for in situ removal efficiency by particle size and resistance to airflow
- BS-EN-ISO-29463-2 - High-efficiency filters and filter media for removing particles in air
- BS-EN-ISO-29463-3 - High-efficiency filters and filter media for removing particles in air
- BS-EN-ISO-29463-4 - High-efficiency filters and filter media for removing particles in air
- BS-EN-ISO-29463-5 - High-efficiency filters and filter media for removing particles in air
- BS-EN-ISO-29463-5-TC - Tracked Changes. High-efficiency filters and filter media for removing particles in air
- BS-EN-ISO-29464 - Cleaning of air and other gases. Terminology
- BS-ISO-10294-1 - Fire resistance tests. Fire dampers for air distribution systems
- BS-ISO-10294-2 - Fire-resistance tests. Fire dampers for air distribution systems
- BS-ISO-10294-3 - Fire-resistance tests. Fire dampers for air distribution systems
- BS-ISO-10294-4 - Fire resistance tests. Fire dampers for air distribution systems
- BS-ISO-10294-5 - Fire-resistance tests. Fire dampers for air distribution systems
- BS-ISO-15714 - Method of evaluating the UV dose to airborne microorganisms transiting in-duct ultraviolet germicidal irradiation devices
- BS-ISO-15727 - UV-C devices. Measurement of the output of a UV-C lamp
- BS-ISO-22031 - Sampling and test method for cleanable filter media taken from filters of systems in operation
- BS-ISO-23139 - Biological equipment for treating air and other gases. Requirements and application guidance for deodorization in wastewater treatment plants
- BS-ISO-29464 - Cleaning of air and other gases. Terminology
- DD-CEN-14175-5 - Fume cupboards
- DD-ENV-12102 - Air conditioners, heat pumps and dehumidifiers with electrically driven compressors. Measurement of airborne noise. Determination of the sound power level
- PD-CEN-14788 - Ventilation for buildings. Design and dimensioning of residential ventilation systems
- PD-CEN-15316-6-3 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- PD-CEN-15316-6-8 - Energy performance of buildings. Method for calculation of system energy requirements and system efficiencies
- PD-CEN-15500-2 - Energy Performance of Buildings. Control for heating, ventilating and air-conditioning applications
- PD-CEN-16244 - Ventilation in hospitals. Coherent hierarchic structure and common terms and definitions for a standard related to ventilation in hospitals
- PD-CEN-16798-10 - Energy performance of buildings. Ventilation for buildings
- PD-CEN/16798-14 - Energy performance of buildings. Ventilation for buildings
- PD-CEN-16798-16 - Energy performance of buildings. Ventilation for buildings
- PD-CEN-16798-18 - Energy performance of buildings. Ventilation for buildings
- PD-CEN-16798-4 - Energy performance of buildings. Ventilation for buildings
- PD-CEN-16798-6 - Energy performance of buildings. Ventilation for buildings
- PD-CEN-16798-8 - Energy performance of buildings. Ventilation for buildings
- PD-CEN-17153 - Ventilation for buildings. Correction of air flow rate according to ambient conditions
- PD-CEN-17441 - Laboratory installations. Ventilation systems in laboratories
- PD-CEN-ISO-21083-2 - Test method to measure the efficiency of air filtration media against spherical nanomaterials
- PD-CEN-ISO-21805 - Guidance on design, selection and installation of vents to safeguard the structural integrity of enclosures protected by gaseous fire-extinguishing systems
- PD-CR-14378 - Ventilation for buildings. Experimental determination of mechanical energy loss coefficients of air handling components
IEC:
ISO:
- ISO-10121-1 - Test method for assessing the performance of gas-phase air cleaning media and devices for general ventilation - Part 1: Gas-phase air cleaning media
- ISO-10121-2 - Test methods for assessing the performance of gas-phase air cleaning media and devices for general ventilation - Part 2: Gas-phase air cleaning devices (GPACD)
- ISO-10121-3 - Test methods for assessing the performance of gas-phase air cleaning media and devices for general ventilation - Part 3: Classification system for GPACDs applied to treatment of outdoor air
- ISO-10294-1 - Fire resistance tests - Fire dampers for air distribution systems - Part 1: Test method
- ISO-10294-1-AM1 - - Amendment 1
- ISO-10294-2 - Fire resistance tests -- Fire dampers for air distribution systems -- Part 2: Classification, criteria and field of application of test results
- ISO-10294-3 - Fire resistance tests -- Fire dampers for air distribution systems -- Part 3: Guidance on the test method
- ISO-10294-4 - Fire resistance tests -- Fire dampers for air distribution systems -- Part 4: Test of thermal release mechanism
- ISO-10294-4-AM1 - - Amendment 1: Specific performance requirement for thermal release mechanism based upon performance of thermal release mechanism used in ISO 10294-1 test specimen
- ISO-10294-5 - Fire resistance tests - Fire dampers for air distribution systems - Part 5: Intumescent fire dampers
- ISO-15714 - Method of evaluating the UV dose to airborne microorganisms transiting in-duct ultraviolet germicidal irradiation devices
- ISO-15727 - UV-C devices - Measurement of the output of a UV-C lamp
- ISO-15858 - UV-C Devices - Safety information - Permissible human exposure
- ISO-15957 - Test dusts for evaluating air cleaning equipment
- ISO-16170 - In situ test methods for high efficiency filter systems in industrial facilities
- ISO-16890-1 - Air filters for general ventilation - Part 1: Technical specifications, requirements and classification system based upon particulate matter efficiency (ePM)
- ISO-16890-2 - Air filters for general ventilation - Part 2: Measurement of fractional efficiency and air flow resistance
- ISO-16890-3 - Air filters for general ventilation - Part 3: Determination of the gravimetric efficiency and the air flow resistance versus the mass of test dust captured
- ISO-16890-4 - Air filters for general ventilation - Part 4: Conditioning method to determine the minimum fractional test efficiency
- ISO-16891 - Test methods for evaluating degradation of characteristics of cleanable filter media
- ISO-21083-1 - Test method to measure the efficiency of air filtration media against spherical nanomaterials - Part 1: Size range from 20 nm to 500 nm
- ISO-21083-2 - Test method to measure the efficiency of air filtration media against spherical nanomaterials - Part 2: Size range from 3 nm to 30 nm
- ISO-21805 - Guidance and recommendations on design, selection and installation of vents to safeguard the structural integrity of enclosures protected by gaseous fire-extinguishing systems
- ISO-22031 - Sampling and test method for cleanable filter media taken from filters of systems in operation
- ISO-23137-1 - Requirements for aerosol filters used in nuclear facilities against specified severe conditions - Part 1: General requirements
- ISO-23139 - Biological equipment for treating air and other gases - Requirements and application guidance for deodorization in wastewater treatment plants
- ISO-29462 - Field testing of general ventilation filtration devices and systems for in situ removal efficiency by particle size and resistance to airflow
- ISO-29463-1 - High efficiency filters and filter media for removing particles from air - Part 1: Classification, performance, testing and marking
- ISO-29463-2 - High-efficiency filters and filter media for removing particles in air - Part 2: Aerosol production, measuring equipment and particle-counting statistics
- ISO-29463-3 - High-efficiency filters and filter media for removing particles in air - Part 3: Testing flat sheet filter media
- ISO-29463-4 - High-efficiency filters and filter media for removing particles in air - Part 4: Test method for determining leakage of filter elements-Scan method
- ISO-29463-5 - High-efficiency filters and filter media for removing particles in air - Part 5: Test method for filter elements
- ISO-29464 - Cleaning of air and other gases - Terminology
- ISO-3258 - Air distribution and air diffusion -- Vocabulary
- ISO-3649 - Cleaning equipment for air or other gases -- Vocabulary
- ISO-5219 - Air distribution and air diffusion -- Laboratory aerodynamic testing and rating of air terminal devices
- ISO-5220 - Air distribution and air diffusion -- Aerodynamic testing and rating of constant and variable dual or single duct boxes and single duct units
- ISO-5220/1 - Addendum 1 to ISO 5220:1981 Variable primary flow rate control devices with induced flow facility
- ISO-5221 - Air distribution and air diffusion -- Rules to methods of measuring air flow rate in an air handling duct
- ISO-6242-2 - Building construction -- Expression of users requirements -- Part 2: Air purity requirements'
- ISO-6584 - Cleaning equipment for air and other gases -- Classification of dust separators
- ISO-6944 - Fire resistance tests - Ventilation ducts
- ISO-6944-1 - Fire containment - Elements of building construction - Part 1: Ventilation ducts
- ISO-6944-1-AM1 - - Amendment 1
- ISO-6944-2 - Fire containment - Elements of building construction - Part 2: Kitchen extract ducts
- ISO-7244 - Air distribution and air diffusion -- Aerodynamic testing of dampers and valves
- ISO-7807 - Air distribution -- Straight circular sheet metal ducts with a lock type spiral seam and straight rectangular sheet metal ducts -- Dimensions
Other SDOs:
- BST-TR-2000 - Luftbehandling (CEN- rapport)
- DIN-EN-12097 - Ventilation for Buildings - Ductwork - Requirements for Ductwork Components To Facilit
- DIN-EN-13053 - Ventilation for buildings - Air handling units - Rating and performance for units, components and sections
- DIN-EN-13141-1 - Part 1: Externally & Internally Mounted Air Transfer Devices, Ventilation for Building
- DIN-EN-13141-2 - Part 2: Exhaust & Supply Air Terminal Devices, Ventilation for Buildings - Performance
- DIN-EN-13141-4 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 4: Fans used in residential ventilation systems
- DIN-EN-13141-5 - Part 5: Cowls & Roof Outlet Terminal Devices, Ventilation for Buildings, Performance T
- DIN-EN-13141-6 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 6: Exhaust ventilation system packages used in a single dwelling; German version EN 13141-6:2014
- DIN-EN-13141-7 - Part 7: Performance Testing of a Mechanical Supply & Exhaust Ventilation, Ventilation
- DIN-EN-13141-8 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 8: Performance testing of un-ducted mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems inte
- DIN-EN-13142 - Ventilation for buildings - Components/products for residential ventilation - Required and optional performance characteristics; German version EN 13142:2013
- DIN-EN-13465 - Ventilation for Buildings, Calculation Methods for the Determination of Air Flow Rates
- DIN-EN-13779 - Ventilation for Non-Residential Buidlings - Performance Requirements for Ventilation &
- DIN-EN-14277 - Ventilation for Buildings - Air Terminal Devices - Method for Airflow Measurement by C
- DIN-EN-14518 - Ventilation for Buildings, Chilled Beams, Testing & Rating of Passive Chilled Beams
- DIN-EN-1507 - Ventilation for Buildings - Sheet Metal Air Ducts With Rectangular Section - Requireme
- DIN-EN-15218 - Air conditioners and liquid chilling packages with evaporatively cooled condenser and with electrically driven compressors for space cooling - Terms, definitions, test conditions, test methods and requirements; German version EN 15218:2013
- EN-12097 - Ventilation for Buildings - Ductwork - Requirements for Ductwork Components To Facilit
- EN-12102 - Air conditioners, liquid chilling packages, heat pumps and dehumidifiers with electrically driven compressors for space heating and cooling - Measurement of airbone noise - Determination of the sound power level
- EN-12236 - Ventilation for Buildings, Ductwork Hangers & Supports, Requirements for Strength
- EN-12309-1 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 1: Terms and definitions
- EN-12309-2 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 2: Safety
- EN-12309-3 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 3: Test conditions
- EN-12309-4 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 4: Test methods
- EN-12309-5 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 5: Requirements
- EN-12309-6 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 6: Calculation of seasonal performances
- EN-12309-7 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 7: Specific provisions for hybrid appliances
- EN-12599 - Ventilation for buildings - Test procedures and measurement methods to hand over air conditioning and ventilation systems
- EN-12735-1 - Copper and copper alloys - Seamless, round tubes for air conditioning and refrigeration - Part 1: Tubes for piping systems
- EN-12735-2 - Copper and copper alloys - Seamless, round tubes for air conditioning and refrigeration - Part 2: Tubes for equipment
- EN-13053 - Ventilation for buildings - Air handling units - Rating and performance for units, components and sections
- EN-13141-10 - Part 10: Humidity Controlled Extract Air Terminal Device, Ventilation for Buildings -
- EN-13141-11 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 11: Supply ventilation units
- EN-13141-2 - Part 2: Exhaust & Supply Air Terminal Devices, Ventilation for Buildings - Performance
- EN-13141-3 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 3: Range hoods for residential use without fan
- EN-13141-4 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 4: Fans used in residential ventilation systems
- EN-13141-5 - Part 5: Cowls & Roof Outlet Terminal Devices, Ventilation for Buildings, Performance T
- EN-13141-6 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 6: Exhaust ventilation system packages used in a single dwelling
- EN-13141-7 - Ventilation for Buildings, Performance Testing of Components/Products for Residential
- EN-13141-8 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 8: Performance testing of un-ducted mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for a single room
- EN-13141-9 - Part 9: Externally Mounted Humidity Controlled Air Transfer Device, Ventilation for B
- EN-13142 - Ventilation for buildings - Components/products for residential ventilation - Required and optional performance characteristics
- EN-13779 - Ventilation for Non-Residential Buidlings - Performance Requirements for Ventilation &
- EN-14037-1 - Free hanging heating and cooling surfaces for water with a temperature below 120 Degrees C - Part 1: Pre-fabricated ceiling mounted radiant panels for space heating - Technical specifications and requirements
- EN-14037-4 - Free hanging heating and cooling surfaces for water with a temperature below 120 Degrees C - Part 4: Pre-fabricated ceiling mounted radiant panels - Test method for cooling capacity
- EN-14277 - Ventilation for Buildings - Air Terminal Devices - Method for Airflow Measurement by C
- EN-14511-1 - Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling - Part 1: Terms and definitions
- EN-14511-2 - Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling - Part 2: Test conditions
- EN-14511-3 - Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling - Part 3: Test methods
- EN-14511-4 - Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling - Part 4: Operating requirements, marking and instructions
- EN-14518 - Ventilation for Buildings, Chilled Beams, Testing & Rating of Passive Chilled Beams
- EN-14825 - Air conditioners, liquid chilling packages and heat pumps, with electrically driven compressors, for space heating and cooling - Testing and rating at part load conditions and calculation of seasonal performance
- EN-14989-2 - Part 2: Flue & Air Supply Ducts for Room Sealed Appliances, Chimneys - Requirements &
- EN-1506 - Ventilation for Buildings - Sheet Metal Air Ducts & Fittings With Circular Cross-Secti
- EN-1507 - Ventilation for Buildings - Sheet Metal Air Ducts With Rectangular Sectio - Requiremen
- EN-15116 - Ventilation in Buildings, Chilled Beams, Testing & Rating of Active Chilled Beams
- EN-15218 - Air conditioners and liquid chilling packages with evaporatively cooled condenser and with electrically driven compressors for space cooling - Terms, definitions, test conditions, test methods and requirements
- EN-15239 - Ventilation for Buildings, Energy Performance of Buildings, Guidelines for Inspection
- EN-15240 - Ventilation for Buildings - Energy Performance of Buildings - Guidelines for Inspecti
- EN-15241 - Ventilation for buildings - Calculation methods for energy losses due to ventilation and infiltration in buildings
- EN-15242 - Ventilation for Buildings, Calculation Methods for the Determination of Air Flow Rates
- EN-15243 - Ventilation for Buildings, Calculation of Room Temperatures & of Load & Energy for Bu
- EN-15316-3 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 3: Space distribution systems (DHW, heating and cooling), Module M3-6, M4-6, M8-6
- EN-15316-4-5 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-5: District heating and cooling, Module M3-8-5, M4-8-5, M8-8-5, M11-8-5
- EN-15377-1 - Part 1: Determination of the Design Heating & Cooling Capacity, Heating Systems in Bui
- EN-15377-2 - Part 2: Design, Dimensioning & Installation, Heating Systems in Buildings - Design Of
- EN-15423 - Ventilation for Buildings, Fire Precaution for Air Distribution Systems in Buildings
- EN-15500-1 - Energy Performance of Buildings - Control for heating, ventilating and air conditioning applications - Part 1: Electronic individual zone control equipment - Modules M3-5, M4-5, M5-5
- EN-15650 - Ventilation for Buildings - Fire Dampers
- EN-15726 - Ventilation for buildings - Air diffusion - Measurements in the occupied zone of air-conditioned/ventilated rooms to evaluate thermal and acoustic conditions
- EN-15727 - Ventilation for Buildings - Ducts & Ductwork Components, Leakage Classification & Test
- EN-15780 - Ventilation for buildings - Ductwork - Cleanliness of ventilation systems
- EN-15805 - Particulate Air Filters for General Ventilation - Standardized Dimensions
- EN-15882-1 - Extended application of results from fire resistance tests for service installations - Part 1: Ducts
- EN-16211 - Ventilation for buildings - Measurement of air flows on site - Methods
- EN-16445 - Ventilation for buildings - Air diffusion - Aerodynamic testing and rating for mixed flow application: non-isothermal procedure for cold jet
- EN-16573 - Ventilation for Buildings - Performance testing of components for residential buildings - Multifunctional balanced ventilation units for single family dwellings, including heat pumps
- EN-16798-17 - Energy performance of buildings - Ventilation for buildings - Part 17: Guidelines for inspection of ventilation and air conditioning systems (Module M4-11, M5-11, M6-11, M7-11)
- EN-16798-5-1 - Energy performance of buildings - Ventilation for buildings - Part 5-1: Calculation methods for energy requirements of ventilation and air conditioning systems (Modules M5-6, M5-8, M6-5, M6-8, M7-5, M7-8) - Method 1: Distribution and generation
- EN-16798-5-2 - Energy performance of buildings - Ventilation for buildings - Part 5-2: Calculation methods for energy requirements of ventilation systems (Modules M5-6, M5-8, M6-5, M6-8, M7-5, M7-8) - Method 2: Distribution and generation
- EN-16798-7 - Energy performance of buildings - Ventilation for buildings - Part 7: Calculation methods for the determination of air flow rates in buildings including infiltration (Modules M5-5)
- EN-1751 - Ventilation for buildings - Air terminal devices - Aerodynamic testing of damper and valves
- EN-1886 - Ventilation for Buildings - Air Handling Units - Mechanical Performance
- EN-779 - Particulate air filters for general ventilation - Determination of the filtration performance
- EN-810 - Dehumidifiers With Electrically Driven Compressors, Rating Tests, Marking, Operational
- EN-ISO-10121-1 - Test method for assessing the performance of gas-phase air cleaning media and devices for general ventilation - Part 1: Gas-phase air cleaning media (ISO 10121-1:2014)
- EN-ISO-10121-2 - Test methods for assessing the performance of gas-phase air cleaning media and devices for general ventilation - Part 2: Gas-phase air cleaning devices (GPACD) (ISO 10121-2:2013)
- EN-ISO-11691 - Acoustics, Measurement of Insertion Loss of Ducted Silencers Without Flow, Laboratory
- EN-ISO-11855-1 - Building environment design - Design, dimensioning, installation and control of embedded radiant heating and cooling systems - Part 1: Definition, symbols, and comfort criteria
- EN-ISO-11855-2 - Building environment design - Design, dimensioning, installation and control of embedded radiant heating and cooling systems - Part 2: Determination of the design heating and cooling capacity
- EN-ISO-11855-3 - Building environment design - Design, dimensioning, installation and control of embedded radiant heating and cooling systems - Part 3: Design and dimensioning
- EN-ISO-11855-4 - Building environment design - Design, dimensioning, installation and control of embedded radiant heating and cooling systems - Part 4: Dimensioning and calculation of the dynamic heating and cooling capacity of Thermo Active Building Systems (TABS)
- EN-ISO-11855-5 - Building environment design - Design , dimensioning, installation and control of embedded radiant heating and cooling systems - Part 5: Installation
- EN-ISO-15858 - UV-C Devices - Safety information - Permissible human exposure
- EN-ISO-15957 - Test dusts for evaluating air cleaning equipment
- EN-ISO-16170 - In situ test methods for high efficiency filter systems in industrial facilities
- EN-ISO-16890-1 - Air filters for general ventilation - Part 1: Technical specifications, requirements and classification system based upon particulate matter efficiency (ePM)
- EN-ISO-16890-2 - Air filters for general ventilation - Part 2: Measurement of fractional efficiency and air flow resistance
- EN-ISO-16890-3 - Air filters for general ventilation - Part 3: Determination of the gravimetric efficiency and the air flow resistance versus the mass of test dust captured
- EN-ISO-16890-4 - Air filters for general ventilation - Part 4: Conditioning method to determine the minimum fractional test efficiency
- EN-ISO-16891 - Test methods for evaluating degradation of characteristics of cleanable filter media
- EN-ISO-29462 - Field testing of general ventilation filtration devices and systems for in situ removal efficiency by particle size and resistance to airflow (ISO 29462:2013)
- EN-ISO-29463-2 - High-efficiency filters and filter media for removing particles in air - Part 2: Aerosol production, measuring equipment and particle-counting statistics
- EN-ISO-29463-3 - High-efficiency filters and filter media for removing particles in air - Part 3: Testing flat sheet filter media
- EN-ISO-29463-4 - High-efficiency filters and filter media for removing particles in air - Part 4: Test method for determining leakage of filter elements-Scan method
- EN-ISO-29463-5 - High-efficiency filters and filter media for removing particles in air - Part 5: Test method for filter elements
- EN-ISO-636 - Welding consumables - Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels - Classification
- GB/T-34012 - Air cleaner for ventilation system (TEXT OF DOCUMENT IS IN ENGLISH)
- JIS-A-4009 - Components of air duct
- SIS-CEN/CR-14378 - Ventilation for buildings - Experimental determination of mechanical energy loss coefficients of air handling components
- SIS-CEN-ISO-21805 - Guidance on design, selection and installation of vents to safeguard the structural integrity of enclosures protected by gaseous fire-extinguishing systems (ISO/TS 21805:2018).
- SIS-CEN/TR-15316-6-3 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 6-3: Explanation and justification of 15316-3, Module M3-6, M4-6, M8-6
- SIS-CEN/TR-15316-6-8 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 6-8: Explanation and justification of EN 15316-4-5 (District heating and cooling), Module M3-8-5, M4-8-5, M8-8-5, M11-8-5
- SIS-CEN/TR-15500-2 - Energy Performance of Buildings - Control for heating, ventilating and air-conditioning applications - Part 2: Accompanying TR prEN 15500-1:2015 - Modules M3-5,M4-5,M5-5
- SIS-CEN/TR-16798-14 - Energy performance of buildings - Ventilation for buildings - Part 14: Interpretation of the requirements in EN 16798-13 - Calculation of cooling systems (Module M4-8) - Generation
- SIS-CEN/TR-16798-4 - Energy performance of buildings - Ventilation for buildings - Part 4: Interpretation of the requirements in EN 16798- 3 - For non-residential buildings - Performance requirements for ventilation and room-conditioning systems(Modules M5-1, M5-4)
- SIS-CEN/TS-16244 - Ventilation in hospitals - Coherent hierarchic structure and common terms and definitions for a standard related to ventilation in hospitals
- SIS-CEN/TS-17441 - Laboratory installations - Ventilation systems in laboratories
- SIS-CEN/TS-17606 - Installation of refrigeration, air conditioning and heat pump equipment containing flammable refrigerants, complementing existing standards
- SIS-CEN/TS-17607 - Operation, servicing, maintenance, repair and decommissioning of refrigeration, air conditioning and heat pump equipment containing flammable refrigerants, complementing existing standards
- SIS-TS-39 - Microbiological cleanliness in the operating room - Preventing airborne contamination - Guidance and fundamental requirements
- SS-EN-12097 - Ventilation for buildings - Ductwork - Requirements for ductwork components to facilitate maintenance of ductwork systems
- SS-EN-12102 - Air conditioners, liquid chilling packages, heat pumps and dehumidifiers with electrically driven compressors for space heating and cooling - Measurement of airborne noise - Determination of the sound power level
- SS-EN-12102-1 - Air conditioners, liquid chilling packages, heat pumps, process chillers and dehumidifiers with electrically driven compressors - Determination of the sound power level - Part 1: Air conditioners, liquid chilling packages, heat pumps for space heating and cooling, dehumidifiers and process chillers
- SS-EN-12220 - Ventilation for buildings - Ductwork - Dimensions of circular flanges for general ventilation
- SS-EN-12236 - Ventilation for buildings - Ductwork hangers and supports - Requirements for strength
- SS-EN-12237 - Ventilation for buildings - Ductwork - Strength and leakage of circular sheet metal ducts
- SS-EN-12238 - Ventilation for buildings - Air terminal devices - Aerodynamic testing and rating for mixed flow applications
- SS-EN-12239 - Ventilation for buildings - Air terminal devices - Aerodynamic testing and rating for displacement flow applications
- SS-EN-12309-1 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 1: Terms and definitions
- SS-EN-12309-2 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 2: Safety
- SS-EN-12309-3 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 3: Test conditions
- SS-EN-12309-4 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 4: Test methods
- SS-EN-12309-5 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 5: Requirements
- SS-EN-12309-6 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 6: Calculation of seasonal performances
- SS-EN-12309-7 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 7: Specific provisions for hybrid appliances
- SS-EN-12589 - Ventilation for buildings - Air terminal units - Aerodynamic testing and rating of constant and variable rate terminal units
- SS-EN-12599 - Ventilation for buildings - Test procedures and measurement methods to hand over air conditioning and ventilation systems
- SS-EN-12735-1 - Copper and copper alloys - Seamless, round tubes for air conditioning and refrigeration - Part 1: Tubes for piping systems
- SS-EN-12735-1-AM1 - Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 1: Tubes for piping systems
- SS-EN-12735-2 - Copper and copper alloys - Seamless, round tubes for air conditioning and refrigeration - Part 2: Tubes for equipment
- SS-EN-12735-2-AM1 - Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 2: Tubes for equipment
- SS-EN-12792 - Ventilation for buildings - Symbols, terminology and graphical symbols
- SS-EN-13030 - Ventilation for buildings - Terminals - Performance testing of louvres subjected to simulated rain
- SS-EN-13053 - Ventilation for buildings - Air handling units - Rating and performance for units, components and sections
- SS-EN-13141-1 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 1: Externally and internally mounted air transfer devices
- SS-EN-13141-10 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 10: Humidity controlled extract air terminal device
- SS-EN-13141-11 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 11: Supply ventilation units
- SS-EN-13141-2 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 2: Exhaust and supply air terminal devices
- SS-EN-13141-3 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 3: Range hoods for residential use without fan
- SS-EN-13141-4 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 4: Aerodynamic, electrical power and acoustic performance of unidirectional ventilation units
- SS-EN-13141-5 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 5: Cowls, assisted cowls and roof outlet terminal devices
- SS-EN-13141-6 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 6: Exhaust ventilation system packages used in a single dwelling
- SS-EN-13141-7 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 7: Performance testing of ducted mechanical supply and exhaust ventilation units (including heat recovery)
- SS-EN-13141-8 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 8: Performance testing of non-ducted mechanical supply and exhaust ventilation units (including heat recovery)
- SS-EN-13141-9 - Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 9: Externally mounted humidity controlled air transfer device
- SS-EN-13142 - Ventilation for buildings - Components/products for residential ventilation - Required and optional performance characteristics
- SS-EN-13180 - Ventilation for buildings - Ductwork - Dimensions and mechanical requirements for flexible ducts
- SS-EN-13181 - Ventilation for buildings - Terminals - Performance testing of louvres subject to simulated sand
- SS-EN-13182 - Ventilation for buildings - Instrumentation requirements for air velocity measurements in ventilated spaces
- SS-EN-13264 - Ventilation for buildings - Floor mounted air terminal devices - Tests for structural classification
- SS-EN-13403 - Ventilation for buildings - Non-metallic ducts - Ductwork made from insulation ductboards
- SS-EN-13465 - Ventilation for buildings - Calculation methods for the determination of air flow rates in dwellings
- SS-EN-13611 - Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements
- SS-EN-1366-10 - Fire resistance tests for service installations - Part 10: Smoke control dampers
- SS-EN-1366-12 - Fire resistance tests for service installations - Part 12: Non-mechanical fire barrier for ventilation ductwork
- SS-EN-1366-1-AM1 - Fire resistance tests for service installations - Part 1: Ventilation ducts
- SS-EN-13779 - Ventilation for non-residential buildings - Performance requirements for ventilation and room-conditioning systems
- SS-EN-14037-1 - Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 1: Pre-fabricated ceiling mounted radiant panels for space heating - Technical specifications and requirements
- SS-EN-14037-4 - Free hanging heating and cooling surfaces for water with a temperature below 120°C - Part 4: Pre-fabricated ceiling mounted radiant panels - Test method for cooling capacity
- SS-EN-14134 - Ventilation for buildings - Performance measurement and checks for residential ventilation systems
- SS-EN-14239 - Ventilation for buildings - Ductwork - Measurement of ductwork surface area
- SS-EN-14240 - Ventilation for buildings - Chilled ceilings - Testing and rating
- SS-EN-14277 - Ventilation for buildings - Air terminal devices - Method for airflow measurement by calibrated sensors in or close to ATD/Plenum boxes
- SS-EN-14511-1 - Air conditioners, liquid chilling packages and heat pumps for space heating and cooling and process chillers, with electrically driven compressors - Part 1: Terms and definitions
- SS-EN-14511-2 - Air conditioners, liquid chilling packages and heat pumps for space heating and cooling and process chillers, with electrically driven compressors - Part 2: Test conditions
- SS-EN-14511-3 - Air conditioners, liquid chilling packages and heat pumps for space heating and cooling and process chillers, with electrically driven compressors - Part 3: Test methods
- SS-EN-14511-4 - Air conditioners, liquid chilling packages and heat pumps for space heating and cooling and process chillers, with electrically driven compressors - Part 4: Requirements
- SS-EN-14518 - Ventilation for buildings - Chilled beams - Testing and rating of passive chilled beams
- SS-EN-14825 - Air conditioners, liquid chilling packages and heat pumps, with electrically driven compressors, for space heating and cooling, commercial and process cooling - Testing and rating at part load conditions and calculation of seasonal performance
- SS-EN-14989-2 - Chimneys - Requirements and test methods for metal chimneys and material independent air supply ducts for roomsealed heating applications - Part 2: Flue and air supply ducts for room sealed appliances
- SS-EN-14992 - Precast concrete products - Wall elements
- SS-EN-1505 - ventilation for buildings - Sheet metal air ducts and fittings with rectangular cross section - Dimensions
- SS-EN-1506 - Ventilation for buildings - Sheet metal air ducts and fittings with circular cross-section - Dimensions
- SS-EN-1507 - Ventilation for buildings - Sheet metal air ducts with rectangular section - Requirements for strength and leakage
- SS-EN-15116 - Ventilation in buildings - Chilled beams - Testing and rating of active chilled beams
- SS-EN-15218 - Air conditioners and liquid chilling packages with evaporatively cooled condenser and with electrically driven compressors for space cooling - Terms, definitions, test conditions, test methods and requirements
- SS-EN-15239 - Ventilation for buildings - Energy performance of buildings - Guidelines for inspection of ventilation systems
- SS-EN-15240 - Ventilation for buildings - Energy performance of buildings - Guidelines for inspection of air-conditioning systems
- SS-EN-15241 - Ventilation for buildings - Calculation methods for energy losses due to ventilation and infiltration in buildings
- SS-EN-15242 - Ventilation for buildings - Calculation methods for the determination of air flow rates in buildings including infiltration
- SS-EN-15243 - Ventilation for buildings - Calculation of room temperatures and of load and energy for buildings with room conditioning systems
- SS-EN-15316-3 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 3: Space distribution systems (DHW, heating and cooling), Module M3-6, M4-6, M8-6
- SS-EN-15316-4-5 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-5: District heating and cooling, Module M3-8-5, M4-8-5, M8-8-5, M11-8-5
- SS-EN-15377-1 - Heating systems in buildings - Design of embedded water based surface heating and cooling systems - Part 1: Determination of the design heating and cooling capacity
- SS-EN-15377-2 - Heating systems in buildings - Design of embedded water based surface heating and cooling systems - Part 2: Design, dimensioning and installation
- SS-EN-15423 - Ventilation for buildings - Fire precautions for air distribution systems in buildings
- SS-EN-15500-1 - Energy Performance of Buildings - Control for heating, ventilating and air conditioning applications - Part 1: Electronic individual zone control equipment - Modules M3-5, M4-5, M5-5
- SS-EN-15650 - Ventilation for buildings - Fire dampers
- SS-EN-15665 - Ventilation in buildings - Determining performance criteria for design of residential ventilation systems
- SS-EN-15726 - Ventilation for buildings - Air diffusion - Measurements in the occupied zone of air-conditioned/ventilated rooms to evaluate thermal and acoustic conditions
- SS-EN-15727 - Ventilation for buildings - Ducts and ductwork components, leakage classification and testing
- SS-EN-15780 - Ventilation for buildings - Ductwork - Cleanliness of ventilation systems
- SS-EN-15805 - Particulate air filters for general ventilation - Standardised dimensions
- SS-EN-15882-1 - Extended application of results from fire resistance tests for service installations - Part 1: Ducts
- SS-EN-16211 - Ventilation for buildings - Measurement of air flows on site - Methods
- SS-EN-16282-2 - Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 2: Kitchen ventilation hoods; design and safety requirements
- SS-EN-16282-3 - Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 3: Kitchen ventilation ceilings; design and safety requirements
- SS-EN-16445 - Ventilation for buildings - Air diffusion - Aerodynamic testing and rating for mixed flow application: non-isothermal procedure for cold jet
- SS-EN-16573 - Ventilation for Buildings - Performance testing of components for residential buildings - Multifunctional balanced ventilation units for single family dwellings, including heat pumps
- SS-EN-16798-13 - Energy performance of buildings - Ventilation for buildings - Part 13: Calculation of cooling systems (Module M4-8) - Generation
- SS-EN-16798-15 - Energy performance of buildings - Ventilation for buildings - Part 15: Calculation of cooling systems (Module M4-7) - Storage
- SS-EN-16798-17 - Energy performance of buildings - Ventilation for buildings - Part 17: Guidelines for inspection of ventilation and air conditioning systems (Module M4-11, M5-11, M6-11, M7-11)
- SS-EN-16798-3 - Energy performance of buildings - Ventilation for buildings - Part 3: For non-residential buildings - Performance requirements for ventilation and room-conditioning systems (Modules M5-1, M5-4)
- SS-EN-16798-5-1 - Energy performance of buildings - Ventilation for buildings - Part 5-1: Calculation methods for energy requirements of ventilation and air conditioning systems (Modules M5-6, M5-8, M6-5, M6-8, M7-5, M7-8) - Method 1: Distribution and generation
- SS-EN-16798-5-2 - Energy performance of buildings Modules M5-6, M5-8 Ventilation for buildings Calculation methods for energy requirements of ventilation systems Part 5-2: Distribution and generation (revision of EN 15241) - method 2
- SS-EN-16798-7 - Energy performance of buildings - Ventilation for buildings - Part 7: Calculation methods for the determination of air flow rates in buildings including infiltration (Modules M5-5)
- SS-EN-16798-9 - Energy performance of buildings - Ventilation for buildings - Part 9: Calculation methods for energy requirements of cooling systems (Modules M4-1, M4-4, M4-9) - General
- SS-EN-17088 - Side curtain ventilation systems - Safety
- SS-EN-17192 - Ventilation for buildings - Ductwork - Non-metallic ductwork - Requirements and test methods
- SS-EN-1751 - Ventilation for buildings - Air terminal devices - Aerodynamic testing of damper and valves
- SS-EN-1822-1 - High efficiency air filters (EPA, HEPA and ULPA) - Part 1: Classification, performance testing, marking
- SS-EN-1822-2 - High efficiency air filters (EPA, HEPA and ULPA) - Part 2: Aerosol production, measuring equipment, particle counting statistics
- SS-EN-1822-3 - High efficiency air filters (EPA, HEPA and ULPA) - Part 3: Testing flat sheet filter media
- SS-EN-1822-4 - High efficiency air filters (EPA, HEPA and ULPA) - Part 4: Determining leakage of filter elements (scan method)
- SS-EN-1822-5 - High efficiency air filters (EPA, HEPA and ULPA) - Part 5: Determining the efficiency of filter elements
- SS-EN-1886 - Ventilation for buildings - Air handling units - Mechanical performance
- SS-EN-779 - Particulate air filters for general ventilation - Determination of the filtration performance
- SS-EN-810 - Dehumidifiers with electrically driven compressors - Rating tests, marking, operational requirements and technical data sheet
- SS-EN-814-1 - Air conditioners and heat pumps with electricallydriven compressors - Cooling mode - Part 1: Terms, definitions and designations
- SS-EN-814-2 - Air conditioners and heat pumps with electricallydriven compressors - Cooling mode - Part 2: Testing and requirements for marking
- SS-EN-814-3 - Air conditioners and heat pumps with electricallydriven compressors - Cooling mode - Part 3: Requirements
- SS-EN-ISO-10121-1 - Test method for assessing the performance of gas-phase air cleaning media and devices for general ventilation - Part 1: Gas-phase air cleaning media (ISO 10121-1:2014)
- SS-EN-ISO-10121-2 - Test methods for assessing the performance of gas-phase air cleaning media and devices for general ventilation - Part 2: Gas-phase air cleaning devices (GPACD) (ISO 10121-2:2013)
- SS-EN-ISO-10121-3 - Test methods for assessing the performance of gas-phase air cleaning media and devices for general ventilation - Part 3: Classification system for GPACDs applied to treatment of outdoor air (ISO 10121-3:2022)
- SS-EN-ISO-11691 - Acoustics - Measurement of insertion loss of ducted silencers without flow - Laboratory survey method (ISO 11691:2020)
- SS-EN-ISO-11820 - Acoustics - Measurements on silencers in situ (ISO 11820:1996)
- SS-EN-ISO-11855-1 - Building environment design - Embedded radiant heating and cooling systems - Part 1: Definitions, symbols, and comfort criteria (ISO 11855-1:2021)
- SS-EN-ISO-11855-1-AM1 - Building environment design - Embedded radiant heating and cooling systems - Part 1: Definitions, symbols, and comfort criteria - Amendment 1 (ISO 11855-1:2021/Amd 1:2023)
- SS-EN-ISO-11855-2 - Building environment design - Embedded radiant heating and cooling systems - Part 2: Determination of the design heating and cooling capacity (ISO 11855-2:2021)
- SS-EN-ISO-11855-2-AM1 - Building environment design - Embedded radiant heating and cooling systems - Part 2: Determination of the design heating and cooling capacity - Amendment 1 (ISO 11855-2:2021/DAM 1:2023)
- SS-EN-ISO-11855-3 - Building environment design - Embedded radiant heating and cooling systems - Part 3: Design and dimensioning (ISO 11855-3:2021)
- SS-EN-ISO-11855-3-AM1 - Building environment design - Embedded radiant heating and cooling systems - Part 3: Design and dimensioning - Amendment 1 (ISO 11855-3:2021/Amd 1:2023)
- SS-EN-ISO-11855-4 - Building environment design - Embedded radiant heating and cooling systems - Part 4: Dimensioning and calculation of the dynamic heating and cooling capacity of Thermo Active Building Systems (TABS) (ISO 11855-4:2021)
- SS-EN-ISO-11855-4-AM1 - Building environment design - Embedded radiant heating and cooling systems - Part 4: Dimensioning and calculation of the dynamic heating and cooling capacity of Thermo Active Building Systems (TABS) - Amendment 1 (ISO 11855-4:2021/Amd 1:2023)
- SS-EN-ISO-11855-5 - Building environment design - Embedded radiant heating and cooling systems - Part 5: Installation (ISO 11855-5:2021)
- SS-EN-ISO-15858 - UV-C Devices - Safety information - Permissible human exposure (ISO 15858:2016)
- SS-EN-ISO-15957 - Test dusts for evaluating air cleaning equipment (ISO 15957:2015)
- SS-EN-ISO-16170 - In situ test methods for high efficiency filter systems in industrial facilities (ISO 16170:2016)
- SS-EN-ISO-16890-1 - Air filters for general ventilation - Part 1: Technical specifications, requirements and classification system based upon particulate matter efficiency (ePM) (ISO 16890-1:2016)
- SS-EN-ISO-16890-2 - Air filters for general ventilation - Part 2: Measurement of fractional efficiency and air flow resistance (ISO 16890-2:2022)
- SS-EN-ISO-16890-3 - Air filters for general ventilation - Part 3: Determination of the gravimetric efficiency and the air flow resistance versus the mass of test dust captured (ISO 16890-3:2016)
- SS-EN-ISO-16890-4 - Air filters for general ventilation - Part 4: Conditioning method to determine the minimum fractional test efficiency (ISO 16890-4:2022)
- SS-EN-ISO-16891 - Test methods for evaluating degradation of characteristics of cleanable filter media (ISO 16891:2016)
- SS-EN-ISO-21083-1 - Test method to measure the efficiency of air filtration media against spherical nanomaterials - Part 1: Size range from 20 nm to 500 nm (ISO 21083-1:2018)
- SS-EN-ISO-21805 - Guidance and recommendations on design, selection and installation of vents to safeguard the structural integrity of enclosures protected by gaseous fire-extinguishing systems (ISO 21805:2023)
- SS-EN-ISO-29462 - Field testing of general ventilation filtration devices and systems for in situ removal efficiency by particle size and resistance to airflow (ISO 29462:2022)
- SS-EN-ISO-29463-2 - High-efficiency filters and filter media for removing particles in air - Part 2: Aerosol production, measuring equipment and particle-counting statistics (ISO 29463-2:2011, IDT)
- SS-EN-ISO-29463-3 - High-efficiency filters and filter media for removing particles in air - Part 3: Testing flat sheet filter media (ISO 29463-3:2011)
- SS-EN-ISO-29463-4 - High-efficiency filters and filter media for removing particles in air - Part 4: Test method for determining leakage of filter elements-Scan method (ISO 29463-4:2011)
- SS-EN-ISO-29463-5 - High-efficiency filters and filter media for removing particles in air - Part 5: Test method for filter elements (ISO 29463-5:2022)
- SS-EN-ISO-29464 - Cleaning of air and other gases - Terminology (ISO 29464:2017)
- SS-ENV-12097 - Ventilation for buildings - Ductwork - Requirements for ductwork components to facilitate maintenance of ductwork systems
- SS-ENV-12102 - Air conditioners, heat pumps and dehumidifiers with electrically driven compressors - Measurement of airborne noise - Determination of the sound power level
- SS-ISO-11274 - Soil quality - Determination of the water-retention characteristic - Laboratory methods (ISO 11274:1998/Cor 1:2009, IDT)
- SS-ISO-12499 - Industrial fans - Mechanical safety of fans - Guarding
- SS-ISO-13349 - Industrial fans - Vocabulary and definitions of categories
- SS-ISO-13350 - Industrial fans - Performance testing of jet fans
- SS-ISO-13351 - Industrial fans - Dimensions
- SS-ISO-13363 - Rubber and plastics hoses for marine-engine wet-exhaust systems - Specification (ISO 13363:2015, IDT)
- SS-ISO-29463-1 - High efficiency filters and filter media for removing particles from air - Part 1: Classification, performance, testing and marking (ISO 29463-1:2017, IDT)
- SS-ISO-29463-2 - High-efficiency filters and filter media for removing particles in air - Part 2: Aerosol production, measuring equipment and particle-counting statistics (ISO 29463-2:2011, IDT)
- SS-ISO-29463-3 - High-efficiency filters and filter media for removing particles in air - Part 3: Testing flat sheet filter media (ISO 29463-3:2011, IDT)
- SS-ISO-29463-4 - High-efficiency filters and filter media for removing particles in air - Part 4: Test method for determining leakage of filter elements - Scan method (ISO 29463-4:2011, IDT)
- SS-ISO-29463-5 - High-efficiency filters and filter media for removing particles in air - Part 5: Test method for filter elements (SO 29463-5:2011, IDT)
- SS-ISO-5220 - Air distribution and air diffusion - Aerodynamic testing and rating of constant and variable dual or single duct boxes and single duct units
- SS-ISO-5221 - Air distribution and air diffusion - Rules to methods of measuring air flow rate in an air handlingduct
- SS-ISO-6944-1 - Fire containment - Elements of building construction - Part 1: Ventilation ducts (ISO 6944-1:2008, IDT)
- SS-ISO-6944-2 - Fire containment - Elements of building construction - Part 2: Kitchen extract ducts (ISO 6944-2:2009, IDT)
- SS-ISO-7244 - Air distribution and air diffusion - Aerodynamic testing of dampers and valves
- ULC-S112 - Standard Method of Fire Test of Fire Damper Assemblies
- UNE-100030 - Guidelines for prevention and control of proliferation and spread of Legionella in facilities
- UNE-EN-12309-2 - Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 2: Safety
- UNE-EN-ISO-11855-2 - Building environment design - Design, dimensioning, installation and control of embedded radiant heating and cooling systems - Part 2: Determination of the design heating and cooling capacity