ASTM-A521 › Standard Specification for Steel, Closed-Impression Die Forgings for General Industrial Use (Withdrawn 2018)
The following bibliographic material is provided to assist you with your purchasing decision:
This specification covers untreated and heat-treated steel closed-impression die forgings for general industrial use. The Grades of forgings are as follows: Grades CA, CC, CC1, CE, CF, CF1, CG, AA, AB, AC, AD, AE, AF, AG, and AH. These Grades shall be annealed, normalized, tempered and quenched. The manufactured forgings shall be free from harmful surface discontinuities, roughness, excessive scale, and fins which are indications of overheating, burning, or other injurious conditions. A tensile test shall be done in order to determine the yield strength of the heat-treated forgings. The forgings shall be furnished in a scale-free condition and may be cleaned by acid pickling, grit blasting, sand blasting, or other abrasive method.
Scope
1.1 This specification covers untreated and heat-treated steel, closed-impression die forgings (Note 1) for general industrial use.
Note 1: For the definition of a forging, refer General Requirements Specification A788/A788M.
1.2 The Grades of forgings are as follows, the choice depending on design and stress or service to be imposed:
1.2.1 Grade CA—Untreated, carbon steel forgings,
1.2.2 Grades CC, CC1, and CE—Annealed, normalized and tempered, carbon steel forgings,
1.2.3 Grade CF—Normalized and tempered carbon steel forgings,
1.2.4 Grade CF1—Double normalized and tempered carbon steel forgings,
1.2.5 Grade CG—Quenched and tempered, or normalized, quenched and tempered carbon steel forgings,
1.2.6 Grade AA—Annealed, normalized, or normalized and tempered alloy steel forgings,
1.2.7 Grades AB and AC—Normalized and tempered alloy steel forgings, and
1.2.8 Grades AD, AE, AF, AG, and AH—Normalized, quenched, and tempered alloy steel forgings.
1.3 Unless the order specifies the applicable “M” specification designation, the forgings shall be furnished with the inch-pound units.
1.4 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standard. Within the text and tables, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
Keywords
alloy steel; carbon steel; closed die; forging tolerances; heat treated; impression die; steel forgings;; ICS Number Code 77.140.85 (Iron and steel forgings)
To find similar documents by ASTM Volume:
01.05 (Steel--Bars, Forgings, Bearing, Chain, Tool)
To find similar documents by classification:
77.140.85 (Iron and steel forgings)
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Customers who bought this document also bought:
ASTM-A1008Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable
ASTM-D2240
Standard Test Method for Rubber Property—Durometer Hardness
ASTM-A1011
Standard Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength
Document Number
ASTM-A521/A521M-06(2016)
Revision Level
2006 R16 EDITION
Status
Superseded
Modification Type
Withdrawn
Publication Date
April 1, 2016
Document Type
Specification
Page Count
9 pages
Committee Number
A01.06