ASTM-A599 › Standard Specification for Tin Mill Products, Electrolytic Tin-Coated, Cold-Rolled Sheet
Show Complete Document History
The following bibliographic material is provided to assist you with your purchasing decision:
This specification covers cold-rolled steel sheet in coils or in cut lengths, tin-coated by electrodeposition. The product is commonly known as electrolytic tin-coated sheet, and is for applications that need good solderability, good surface appearance, and a degree of corrosion resistance. The material shall conform to specified chemical composition requirements. The mechanical property requirements for structural steel, high-strength low-alloy steel with and without improved formability, commercial steel, and deep drawing steel are presented in details. The weight [mass] of coating shall conform to specified requirements fit for individual coating designations. The typical methods for determination of tin coating weights are described.
Scope
1.1 This specification covers cold-rolled steel sheet in coils or in cut lengths, tin-coated by electrodeposition. The product is commonly known as electrolytic tin-coated sheet, and is for applications that need good solderability, good surface appearance, and a degree of corrosion resistance. Tin-coated sheet is produced to various designations of tin coating, as outlined in Table 1.
TABLE 1 Electrolytic Tin-Coated Sheets Coating Weight [Mass]
Note 1: Listed below are the commonly produced coating weights [mass] upon agreement between the producer and the purchaser. Other combinations of coatings may be specified and the appropriate minimum average test valuesA apply.
Designation No. | Nominal Tin Coating | Minimum Average Coating |
5 (0.6/0.6) | 0.025/0.025 (0.6/0.6) | 0.02/0.02 (0.5/0.5) |
10 (1.1/1.1) | 0.05/0.05 (1.1/1.1) | 0.04/0.04 (0.9/0.9) |
15 (1.7/1.7) | 0.075/0.075 (1.7/1.7) | 0.06/0.06 (1.4/1.4) |
20 (2.2/2.2) | 0.10/0.10 (2.2/2.2) | 0.08/0.08 (1.8/1.8) |
25 (2.8/2.8) | 0.125/0.125 (2.8/2.8) | 0.11/0.11 (2.5/2.5) |
50 (5.6/5.6) | 0.25/0.25 (5.6/5.6) | 0.23/0.23 (5.2/5.2) |
75 (8.4/8.4) | 0.375/0.375 (8.4/8.4) | 0.35/0.35 (7.8/7.8) |
100 (11.2/11.2) | 0.50/0.50 (11.2/11.2) | 0.45/0.45 (10.1/10.1) |
1.1.1 Electrolytic tin-coated sheet is customarily available as commercial steel (CS); drawing steel (DS); deep drawing steel (DDS); extra deep drawing steel (EDDS), and structural steel (SS). The tin coating is available as unmelted or melted.
1.2 Limitations—This specification is applicable to orders in either inch-pound units (as A599), which is supplied in thicknesses from 0.015 in. to 0.036 in., or SI units [as A599M], which is supplied in thicknesses from 0.381 mm to 0.914 mm. For thicknesses lighter than 0.015 in. [0.381 mm], refer to A624/A624M [A624M].
1.3 Unless the order shows the “M” designation [SI units], the product shall be furnished to inch-pound units. The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
To find similar documents by ASTM Volume:
To find similar documents by classification:
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Customers who bought this document also bought:
MIL-STD-810Environmental Engineering Considerations and Laboratory Tests
91/263/EEC
Telecommunications Terminal Equipment, Including the Mutualrecognition of Their Confo
MIL-STD-100
Engineering Drawing Practices (Superseded by ASME-Y14.100, ASME-Y14.24, ASME-Y14.35m, and ASME-14.34m)
Document Number
ASTM-A599/A599M-07(2017)
Revision Level
2007 R17 EDITION
Status
Current
Modification Type
Reapproval
Publication Date
Sept. 1, 2017
Document Type
Specification
Page Count
3 pages
Committee Number
A01.20