ASTM-B108 › Historical Revision Information
Standard Specification for Aluminum-Alloy Permanent Mold Castings
The following bibliographic material is provided to assist you with your purchasing decision:
This specification covers aluminum-alloy permanent mold castings. The responsibility of furnishing castings that can be laid out and machined to the finished dimensions within the permissible variations specified shall rest with the producer, except where mold equipment is furnished by the purchaser. Samples for chemical analysis shall be taken by sawing, drilling, or milling the casting or test specimens in such a manner as to be representative of the material. Unless otherwise specified, only aluminum or producers foundry scrap shall be used in the re-melting furnace from which molten metal is taken for pouring directly into castings. Pure materials, recycled materials, and master alloys may be used to make alloys conforming to this specification. Foundry control shall consist of examination of castings by radiographic or other approved methods for determining internal discontinuities until the gating, pouring, and other foundry practices have been established to produce castings meeting the quality standards furnished by the purchaser or agreed upon by the purchaser and the producer. Separately cast test specimens shall be cast in iron molds. If the castings are to be heat treated and separately cast specimens are to be used, the specimens representing such castings shall be heat treated with the castings they represent. If castings are to be heat treated and tests are to be obtained on the castings, the test specimens shall be taken from the castings after heat treatment. One per melt-heat combination shall be tested when tensile properties of castings are to be determined. The finished castings shall be uniform in composition and free of blowholes, cracks, shrinks, and other discontinuities.
Scope
1.1 This specification covers aluminum-alloy permanent mold castings designated as shown in Table 1.
1.2 This specification is not intended for aluminum-alloy permanent mold castings used in aerospace applications.
1.3 Alloy and temper designations are in accordance with ANSI H35.1/H35.1(M). The equivalent unified numbering system alloy designations are in accordance with Practice E 527
1.4 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units.
1.5 For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see Annex A1 and Annex A2.
1.6 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Keywords
aluminum; permanent mold castings; Aluminum alloys (castings)--specifications; Permanent mold castings--aluminum alloy; UNS A02040 (Aluminum foundry alloy, casting); UNS A02080 (Aluminum foundry alloy, casting); UNS A02130 (Aluminum foundry alloy); UNS A02220 (Aluminum foundry alloy, casting); UNS A02420 (Aluminum foundry alloy, casting); UNS A03190 (Aluminum foundry alloy, casting); UNS A03320 (Aluminum foundry alloy, casting); UNS A03330 (Aluminum foundry alloy, casting); UNS A03360 (Aluminum foundry alloy, casting); UNS A03540 (Aluminum foundry alloy, casting); UNS A03550 (Aluminum foundry alloy, casting); UNS A03560 (Aluminum foundry alloy, casting); UNS A03590 (Aluminum foundry alloy, casting); UNS A04430 (Aluminum foundry alloy, casting); UNS A05130 (Aluminum foundry alloy, casting); UNS A05350 (Aluminum foundry alloy, casting); UNS A07050 (Aluminum foundry alloy, casting); UNS A07070 (Aluminum foundry alloy, casting); UNS A07110 (Aluminum foundry alloy, casting); UNS A07130 (Aluminum foundry alloy, casting); UNS A08500 (Aluminum foundry alloy, casting); UNS A08510 (Aluminum foundry alloy, casting); UNS A08520 (Aluminum foundry alloy, casting); UNS A13560 (Aluminum foundry alloy, casting); UNS A13570 (Aluminum foundry alloy, casting); UNS A14440 (Aluminum foundry alloy, casting); UNS A24430 (Aluminum foundry alloy, casting); UNS A33550 (Aluminum foundry alloy, casting); ICS Number Code 77.150.10 (Aluminium products)
To find similar documents by ASTM Volume:
02.02 (Aluminum and Magnesium Alloys)
To find similar documents by classification:
77.150.10 (Aluminium products)
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Document Number
ASTM-B108/B108M-08
Revision Level
2008 EDITION
Status
Superseded
Modification Type
Revision with Designation Change
Publication Date
June 1, 2008
Document Type
Specification
Page Count
18 pages
Committee Number
B07.01