ASTM-C110 Historical Revision Information
Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone

ASTM-C110 - 2008 EDITION - SUPERSEDED
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:


These test methods cover physical testing of quicklime, hydrated lime, and limestone. Plastic property testing shall include test methods for standard consistency and plasticity of lime putty, water retention of hydrated lime, and air entrainment. Soundness testing shall include test methods for autoclave expansion, and popping and pitting of hydrated lime. Application testing shall include test methods for slaking rate of quicklime, dry brightness of pulverized limestone, limestone grindability determination by the laboratory ball mill method, and settling rate of hydrated lime. Particle size analysis shall include test methods for residue and sieve analysis, fineness of pulverized quicklime and hydrated lime by air permeability, particle size of pulverized limestone, and dry screening of hydrated lime, pulverized quicklime, and limestone by air jet sieving. Density measurement shall include the following test methods: apparent loose density, and apparent packed density of hydrated lime, pulverized quicklime, and limestone; specific gravity of hydrated lime products; and wet sieve analysis of agricultural liming materials.

ORDER

Scope

1.1 These test methods cover physical testing of quicklime and hydrated lime, and of limestone not otherwise covered in ASTM standards.

Note 1—Quicklime and hydrated lime have a high affinity for moisture and carbon dioxide. Caution should be taken to protect both hydrated and quicklime during sampling, storage, and testing (see Practice C 50).

1.2 The test procedures appear in the following order:

Section
Air Entrainment 8
Apparent Loose Density of Hydrated Lime, Pulverized
Quicklime, and Limestone

19
Apparent Packed Density of Hydrated Lime, Pulverized
Quicklime, and Limestone

20
Autoclave Expansion of Hydrated Lime 9
Dry Brightness of Pulverized Limestone 12
Dry Screening by Air Jet Sieve 18
Fineness of Pulverized Quicklime and Hydrated Lime by Air
Permeability

16
Limestone Grindability 13
Particle Size of Pulverized Limestone 17
Plasticity of Lime Putty 6
Popping and Pitting of Hydrated Lime 10
Residue and Sieve Analysis 15
Settling Rate of Hydrated Lime14
Slaking Rate of Quicklime 11
Specific Gravity of Hydrated Lime Products21
Standard Consistency of Lime Putty 5
Water Retention of Hydrated Lime 7
Wet Sieve Analysis of Agricultural Liming Materials22

1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Keywords

apparent density; dry brightness; dry screening; fineness; lime putty; limestone grindability; particle size; slaking rate; Acidity, alkalinity, pH; Air entrainment; Autoclave expansion; Brightness; Change in length; Consistency; Dry brightness; Expansion--concrete materials/applications; Hydrated lime; Lime putty; Limestone; Optical materials/properties/tests; Plasticity index; Popping and pitting; Quicklime; Residue; Settlement; Sieve analysis--building materials; Slaking rate; Water retention

To find similar documents by ASTM Volume:

04.01 (Cement; Lime; Gypsum)

To find similar documents by classification:

91.100.10 (Cement. Gypsum. Lime. Mortar)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

Document Number

ASTM-C110-08

Revision Level

2008 EDITION

Status

Superseded

Modification Type

Revision

Publication Date

June 1, 2008

Document Type

Test Method

Page Count

22 pages

Committee Number

C07.06