Document Center List of Standards on Measurement Of Electrical And Magnetic Quantities Including Measuring Instruments, Instrument Transformers Electric Energy Meters In Buildings, See 91.140.50
ICS Code 17.220.20
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
ASTM:
- ASTM-A343 - Standard Test Method for Alternating-Current Magnetic Properties of Materials at Power Frequencies Using Wattmeter-Ammeter-Voltmeter Method and 25-cm Epstein Test Frame
- ASTM-A698 - Standard Test Method for Magnetic Shield Efficiency in Attenuating Alternating Magnetic Fields
- ASTM-A927 - Standard Test Method for Alternating-Current Magnetic Properties of Toroidal Core Specimens Using the Voltmeter-Ammeter-Wattmeter Method
- ASTM-A932 - Standard Test Method for Alternating-Current Magnetic Properties of Amorphous Materials at Power Frequencies Using Wattmeter-Ammeter-Voltmeter Method with Sheet Specimens
- ASTM-B497 - Standard Guide for Measuring Voltage Drop on Closed Arcing Contacts (Withdrawn 2017)
- ASTM-B667 - Standard Practice for Construction and Use of a Probe for Measuring Electrical Contact Resistance
- ASTM-B878 - Standard Test Method for Nanosecond Event Detection for Electrical Contacts and Connectors
- ASTM-D3382 - Standard Test Methods for Measurement of Energy and Integrated Charge Transfer Due to Partial Discharges (Corona) Using Bridge Techniques
- ASTM-D4519 - Standard Test Method for On-Line Determination of Anions and Carbon Dioxide in High Purity Water by Cation Exchange and Degassed Cation Conductivity
- ASTM-D4935 - Standard Test Method for Measuring the Electromagnetic Shielding Effectiveness of Planar Materials
- ASTM-D5388 - Standard Test Method for Indirect Measurements of Discharge by Step-Backwater Method
- ASTM-D6120 - Standard Test Method for Electrical Resistivity of Anode and Cathode Carbon Material at Room Temperature
- ASTM-D7449 - Standard Test Method for Measuring Relative Complex Permittivity and Relative Magnetic Permeability of Solid Materials at Microwave Frequencies Using Coaxial Air Line
- ASTM-D7917 - Standard Practice for Inductive Wear Debris Sensors in Gearbox and Drivetrain Applications
- ASTM-E1004 - Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy Current) Method
- ASTM-E1016 - Standard Guide for Literature Describing Properties of Electrostatic Electron Spectrometers
- ASTM-E2039 - Standard Test Method for Determining and Reporting Dynamic Dielectric Properties (Withdrawn 2009)
- ASTM-E2884 - Standard Guide for Eddy Current Testing of Electrically Conducting Materials Using Conformable Sensor Arrays
- ASTM-E684 - Standard Practice for Approximate Determination of Current Density of Large-Diameter Ion Beams for Sputter Depth Profiling of Solid Surfaces (Withdrawn 2012)
- ASTM-ES7 - Test Method for Electromagnetic Shielding Effectiveness of Planar Materials (Withdrawn 1988)
- ASTM-F1207M - Standard Specification for Electrical Insulation Monitors for Monitoring Ground Resistance in Active Electrical Systems [Metric]
- ASTM-F1689 - Standard Test Method for Determining the Insulation Resistance of a Membrane Switch
- ASTM-F1796 - Standard Specification for High Voltage Detectors—Part 1 Capacitive Type to be Used for Voltages Exceeding 600 Volts AC
- ASTM-F2213 - Standard Test Method for Measurement of Magnetically Induced Torque on Medical Devices in the Magnetic Resonance Environment
- ASTM-F2939 - Standard Specification for High Voltage Phasing Testers
- ASTM-F46 - Practice for Room Temperature Resistivity Measurements on Thermoelectric Materials (Withdrawn 1993)
- ASTM-F529 - Method for Interpretation of Interferograms of Nominally Plane Wavefronts
- ASTM-F773M - Standard Practice for Measuring Dose Rate Response of Linear Integrated Circuits (Metric)
- ASTM-G59 - Standard Test Method for Conducting Potentiodynamic Polarization Resistance Measurements
BSI:
- BS-37-1 - Specification for electricity meters. General clauses
- BS-37-3 - Specification for electricity meters. Prepayment watt-hour meters, class 2.0 and fixed charge collectors
- BS-37-5 - Specification. Electricity meters. Polyphase kilowatt maximum demand meters
- BS-37-9 - Specification. Electricity meters. Polyphase reactive volt-ampere-hour meters
- BS-4727-2-GROUP-16 - Glossary of electrotechnical, power, telecommunication, electronics, lighting and colour terms. Terms particular to power engineering
- BS-4739-1 - Method for expression of the properties of cathode-ray oscilloscopes. General
- BS-4739-2 - Method for expression of the properties of cathode-ray oscilloscopes. Storage oscilloscopes
- BS-4828 - Guide for partial discharge measurements
- BS-5164 - Specification for indirect-acting electrical indicating and recording instruments and their accessories
- BS-5685-1 - Electricity meters. Specification for Class 0.5, 1 and 2 single-phase and polyphase, single rate and multi-rate watt-hour meters
- BS-5685-2 - Electricity meters. Specification for single-phase coin operated prepayment flat rate and two-part tariff watt-hour meters of Class 2 and fixed charge collectors of Class 2
- BS-5685-3 - Electricity meters. Specification for meters having Class 1 electro-mechanical maximum demand indicators
- BS-5685-4 - Electricity meters. Specification for Class 3 var-hour meters
- BS-5704 - Method for specifying the performance of digital electronic d.c. voltmeters and d.c. electronic analogue-to-digital convertors
- BS-5788 - Method for expression of the properties of sampling oscilloscopes
- BS-5884 - Magnetic materials. Methods for the determination of the relative magnetic permeability of feebly magnetic materials
- BS-6253-1 - Electrical measuring transducers for converting a.c. electrical quantities into d.c. electrical quantities. Method for specifying general purpose transducers
- BS-6253-2 - Electrical measuring transducers for converting a.c. electrical quantities into d.c. electrical quantities. Method for specifying transducers for outdoor use and other severe environments
- BS-6329 - Method of expression of the properties of spectrum analyzers
- BS-6348 - Method for expression of the properties of signal generators
- BS-6653 - Method for expression of the properties of logic analyzers
- BS-7628 - Specification for combined transformers
- BS-7729 - Specification for Instrument Transformers. Three-Phase Voltage Transformers for Voltag
- BS-7856 - Specification for special design and other features of alternating current watthour meters for active energy for use in the UK (Accuracy Classes A and B)
- BS-7856-TC - Tracked Changes. Specification for special design and other features of alternating current watthour meters for active energy for use in the UK (Accuracy Classes A and B)
- BS-7951 - Electricity meters. Alternating-current single-phase static watt-hour telemeters of accuracy class 1 or 2
- BS-8431 - Electrical static meters for secondary metering and sub-metering. Specification
- BS-89-4 - Direct acting indicating analogue electrical measuring instruments and their accessories
- BS-89-5 - Direct acting indicating analogue electrical measuring instruments and their accessories
- BS-89-6 - Direct acting indicating analogue electrical measuring instruments and their accessories
- BS-89-7 - Direct acting indicating analogue electrical measuring instruments and their accessories
- BS-89-8 - Direct acting indicating analogue electrical measuring instruments and their accessories
- BS-89-9 - Direct acting indicating analogue electrical measuring instruments and their accessories
- BS-90 - Specification for direct-acting electrical recording instruments and their accessories
- BS-903-C4 - Physical testing of rubber
- BS-CISPR-16-1 - Specification for radio disturbance and immunity measuring apparatus and methods. Radio disturbance and immunity measuring apparatus
- BS-CISPR-16-2 - Specification for radio disturbance and immunity measuring apparatus and methods. Methods of measurement of disturbances and immunity
- BS-EN-50123-7-2 - Railway applications. Fixed installations. d.c. switchgear. Measurement, control and protection devices for specific use in d.c. traction systems
- BS-EN-50123-7-3 - Railway applications. Fixed installations. d.c. switchgear. Measurement, control and protection devices for specific use in d.c. traction systems
- BS-EN-50191 - Erection and operation of electrical test equipment
- BS-EN-50294 - Measurement method of total input power of ballast-lamp circuits
- BS-EN-50301 - Methods of measurement for the power consumption of audio, video and related equipment
- BS-EN-50366 - Household & Similar Electrical Appliances, Electromagnetic Fields, Methods for Evaluat
- BS-EN-50383 - Basic standard for the calculation and measurement of electromagnetic field strength and SAR related to human exposure from radio base stations and fixed terminal stations for wireless telecommunication systems (110 MHz - 40 GHz)
- BS-EN-50384 - Product standard to demonstrate the compliance of radio base stations and fixed terminal stations for wireless telecommunication systems with the basic restrictions or the reference levels related to human exposure to radio frequency electromagnetic fields (110 MHz - 40 GHz). Occupational
- BS-EN-50385 - Product standard to demonstrate the compliance of base station equipment with radiofrequency electromagnetic field exposure limits (110 MHz - 100 GHz), when placed on the market
- BS-EN-50385-TC - Tracked Changes. Product standard to demonstrate the compliance of base station equipment with radiofrequency electromagnetic field exposure limits (110 MHz - 100 GHz), when placed on the market
- BS-EN-50400 - Basic standard to demonstrate the compliance of fixed equipment for radio transmission (110 MHz - 40 GHz) intended for use in wireless telecommunication networks with the basic restrictions or the reference levels related to general public exposure to radio frequency electromagnetic fields, when put into service
- BS-EN-50401 - Product standard to demonstrate the compliance of base station equipment with radiofrequency electromagnetic field exposure limits (110 MHz - 100 GHz), when put into service
- BS-EN-50413 - Basic standard on measurement and calculation procedures for human exposure to electric, magnetic and electromagnetic fields (0 Hz - 300 GHz)
- BS-EN-50475 - Basic standard for the calculation and the measurement of human exposure to electromagnetic fields from broadcasting service transmitters in the HF bands (3 MHz - 30 MHz)
- BS-EN-50476 - Product standard to demonstrate the compliance of broadcast station transmitters with the reference levels and the basic restrictions related to public exposure to radio frequency electromagnetic fields (3 MHz - 30 MHz)
- BS-EN-50482 - Instrument transformers. Three-phase inductive voltage transformers having Um up to 52kV
- BS-EN-50492 - Basic standard for the in-situ measurement of electromagnetic field strength related to human exposure in the vicinity of base stations
- BS-EN-50647 - Basic standard for the evaluation of workers' exposure to electric and magnetic fields from equipment and installations for the production, transmission and distribution of electricity
- BS-EN-50678 - General procedure for verifying the effectiveness of the protective measures of electrical equipment after repair
- BS-EN-55016-1-4 - Specification for radio disturbance and immunity measuring apparatus and methods
- BS-EN-60044-1 - Instrument transformers. Current transformers
- BS-EN-60044-2 - Instrument transformers. Inductive voltage transformers
- BS-EN-60044-3 - Instrument transformers
- BS-EN-60044-5 - Instrument transformers
- BS-EN-60044-6 - Instrument transformers
- BS-EN-60044-7 - Instrument transformers
- BS-EN-60044-8 - Instrument transformers
- BS-EN-60051-1 - Direct acting indicating analogue electrical measuring instruments and their accessories
- BS-EN-60051-1-TC - Tracked Changes. Direct acting indicating analogue electrical measuring instruments and their accessories
- BS-EN-60060-3 - High voltage test techniques
- BS-EN-60270 - High-voltage test techniques. Partial discharge measurements
- BS-EN-60359 - Electrical and electronic measurement equipment. Expression of performance
- BS-EN-60387 - Specification for Symbols for Alternating-Current Electricity Meters
- BS-EN-60404-13 - Magnetic materials
- BS-EN-60404-14 - Magnetic materials
- BS-EN-60404-5 - Magnetic materials
- BS-EN-60404-5-TC - Tracked Changes. Magnetic materials
- BS-EN-60404-8-1 - Magnetic materials
- BS-EN-60469 - Transitions, pulses and related waveforms. Terms, definitions and algorithms
- BS-EN-60521 - Class 0.5, 1 and 2 alternating-current watthour meters
- BS-EN-60688 - Electrical measuring transducers for converting A.C. and D.C. electrical quantities to analogue or digital signals
- BS-EN-60868-0 - Flickermeter
- BS-EN-61000-4-2 - Electromagnetic compatibility (EMC)
- BS-EN-61000-4-30 - Electromagnetic compatibility (EMC)
- BS-EN-61000-4-6 - Electromagnetic compatibility (EMC)
- BS-EN-61036 - Alternating Current Static Watt-Hour Meters for Active Energy (Classes 1 & 2)
- BS-EN-61083-1 - Digital recorders for measurements in high-voltage impulse tests
- BS-EN-61083-2 - Instruments and software used for measurement in high-voltage and high-current tests
- BS-EN-61326-2-1 - Electrical equipment for measurement, control and laboratory use. EMC requirements
- BS-EN-61557-1 - Electrical safety in low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-61557-10 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-61557-11 - Electrical safety in low voltage distribution systems up to 1000 V a.c. and 1500 V d.c.. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-61557-12 - Electrical safety in low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-61557-13 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-61557-14 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-61557-15 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-61557-16 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-61557-2 - Electrical safety in low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-61557-3 - Electrical safety in low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-61557-4 - Electrical safety in low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-61557-5 - Electrical safety in low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-61557-6 - Electrical safety in low voltage distribution systems up to 1000 V a.c. and 1500 V d.c.. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-61557-7 - Electrical safety in low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-61557-8 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-61557-9 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-61786-1 - Measurement of DC magnetic, AC magnetic and AC electric fields from 1 Hz to 100 kHz with regard to exposure of human beings
- BS-EN-61788-11 - Superconductivity
- BS-EN-61788-15 - Superconductivity
- BS-EN-61788-16 - Superconductivity
- BS-EN-61788-17 - Superconductivity
- BS-EN-61788-3 - Superconductivity
- BS-EN-61788-4 - Superconductivity
- BS-EN-61788-5 - Superconductivity
- BS-EN-61788-7 - Superconductivity
- BS-EN-61788-8 - Superconductivity
- BS-EN-61869-1 - Instrument transformers
- BS-EN-61869-2 - Instrument transformers
- BS-EN-61869-3 - Instrument transformers
- BS-EN-61869-4 - Instrument transformers
- BS-EN-61869-5 - Instrument transformers
- BS-EN-61869-6 - Instrument transformers
- BS-EN-62052-11 - Electricity metering equipment (AC). General requirements, tests and test conditions
- BS-EN-62053-11 - Electricity metering equipment (a.c.). Particular requirements
- BS-EN-62053-21 - Electricity metering equipment (a.c.). Particular requirements
- BS-EN-62053-22 - Electricity metering equipment (a.c.). Particular requirements
- BS-EN-62053-23 - Electricity metering equipment (a.c.). Particular requirements
- BS-EN-62053-24 - Electricity metering equipment (a.c.). Particular requirements
- BS-EN-62053-52 - Electricity metering equipment (AC). Particular requirements
- BS-EN-62056-4-7-TC - Tracked Changes. Electricity metering data exchange. The DLMS/COSEM suite
- BS-EN-62056-5-3 - Electrcity metering data exchange. The DLMS/COSEM suite
- BS-EN-62056-7-3 - Electricity metering data exchange. The DLMS/COSEM suite
- BS-EN-62056-7-5 - Electricity metering data exchange. The DLMS/COSEM suite
- BS-EN-62056-8-6 - Electricity metering data exchange. The DLMS/COSEM suite
- BS-EN-62058-11 - Electricity metering equipment (a.c.). Acceptance inspection
- BS-EN-62058-21 - Electricity metering equipment (a.c.). Acceptance inspection
- BS-EN-62058-31 - Electricity metering equipment (a.c.). Acceptance inspection
- BS-EN-62110 - Electric and magnetic field levels generated by AC power systems. Measurement procedures with regard to public exposure
- BS-EN-62209-1 - Measurement procedure for the assessment of specific absorption rate of human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices
- BS-EN-62209-1-TC - Tracked Changes. Measurement procedure for the assessment of specific absorption rate of human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices
- BS-EN-62209-2 - Human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices. Human models, instrumentation, and procedures
- BS-EN-62226-1 - Exposure to electric or magnetic fields in the low and intermediate frequency range. Methods for calculating the current density and internal electric field induced in the human body
- BS-EN-62226-3-1 - Exposure to electric or magnetic fields in the low and intermediate frequency range. Methods for calculating the current density and internal electric field induced in the human body
- BS-EN-62233 - Measurement methods for electromagnetic fields of household appliances and similar apparatus with regard to human exposure
- BS-EN-62301 - Household electrical appliances. Measurement of standby power
- BS-EN-62431 - Reflectivity of electromagnetic wave absorbers in millimetre wave frequency. Measurement methods
- BS-EN-62442-1 - Energy performance of lamp controlgear
- BS-EN-62562 - Cavity resonator method to measure the complex permittivity of low-loss dielectric plates
- BS-EN-62586-1 - Power quality measurement in power supply systems
- BS-EN-62586-1-TC - Tracked Changes. Power quality measurement in power supply systems
- BS-EN-62586-2 - Power quality measurement in power supply systems
- BS-EN-62689-1 - Current and voltage sensors or detectors, to be used for fault passage indication purposes
- BS-EN-62689-2 - Current and voltage sensors or detectors, to be used for fault passage indication purposes
- BS-EN-62754 - Computation of waveform parameter uncertainties
- BS-EN-62974-1 - Monitoring and measuring systems used for data collection, gathering and analysis
- BS-EN-IEC-55016-1-4 - Specification for radio disturbance and immunity measuring apparatus and methods
- BS-EN-IEC-60051-3 - Direct acting indicating analogue electrical measuring instruments and their accessories
- BS-EN-IEC-60051-4 - Direct acting indicating analogue electrical measuring instruments and their accessories title
- BS-EN-IEC-60051-5 - Direct acting indicating analogue electrical measuring instruments and their accessories
- BS-EN-IEC-60051-6 - Direct acting indicating analogue electrical measuring instruments and their accessories
- BS-EN-IEC-60051-7 - Direct acting indicating analogue electrical measuring instruments and their accessories
- BS-EN-IEC-60051-8 - Direct acting indicating analogue electrical measuring instruments and their accessories
- BS-EN-IEC-60051-9 - Direct acting indicating analogue electrical measuring instruments and their accessories
- BS-EN-IEC-60404-13 - Magnetic materials
- BS-EN-IEC-60404-13-TC - Tracked Changes. Magnetic materials
- BS-EN-IEC-60404-16 - Magnetic materials
- BS-EN-IEC-60404-3 - Magnetic materials
- BS-EN-IEC-60404-6 - Magnetic materials
- BS-EN-IEC-60404-8-11 - Magnetic materials
- BS-EN-IEC-60477-1 - Laboratory resistors
- BS-EN-IEC-60477-1-TC - Tracked Changes. Laboratory resistors
- BS-EN-IEC-60477-2 - Laboratory resistors
- BS-EN-IEC-60477-2-TC - Tracked Changes. Laboratory resistors
- BS-EN-IEC-61083-3 - Instruments and software used for measurement in high-voltage and high-current tests
- BS-EN-IEC-61326-1 - Electrical equipment for measurement, control and laboratory use. EMC requirements
- BS-EN-IEC-61326-1-TC - Tracked Changes. Electrical equipment for measurement, control and laboratory use. EMC requirements
- BS-EN-IEC-61326-2-1-TC - Tracked Changes. Electrical equipment for measurement, control and laboratory use. EMC requirements
- BS-EN-IEC-61326-2-2 - Electrical equipment for measurement, control and laboratory use. EMC requirements
- BS-EN-IEC-61326-2-2-TC - Tracked Changes. Electrical equipment for measurement, control and laboratory use. EMC requirements
- BS-EN-IEC-61326-2-3 - Electrical equipment for measurement, control and laboratory use. EMC requirements
- BS-EN-IEC-61326-2-3-TC - Tracked Changes. Electrical equipment for measurement, control and laboratory use. EMC requirements
- BS-EN-IEC-61326-2-4 - Electrical equipment for measurement, control and laboratory use. EMC requirements
- BS-EN-IEC-61326-2-4-TC - Tracked Changes. Electrical equipment for measurement, control and laboratory use. EMC requirements
- BS-EN-IEC-61326-2-5 - Electrical equipment for measurement, control and laboratory use. EMC requirements
- BS-EN-IEC-61326-2-5-TC - Tracked Changes. Electrical equipment for measurement, control and laboratory use. EMC requirements
- BS-EN-IEC-61326-2-6-TC - Tracked Changes. Electrical equipment for measurement, control and laboratory use. EMC requirements
- BS-EN-IEC-61557-1 - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-IEC-61557-12 - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-IEC-61557-12-TC - Tracked Changes. Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-IEC-61557-17 - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-IEC-61557-1-TC - Tracked Changes. Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-IEC-61557-2 - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-IEC-61557-2-TC - Tracked Changes. Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-IEC-61557-3 - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-IEC-61557-4 - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures
- BS-EN-IEC-61557-4-TC - Tracked Changes. Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-IEC-61557-5 - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-IEC-61557-5-TC - Tracked Changes. Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-IEC-61557-6 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c.. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-IEC-61557-6-TC - Tracked Changes. Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c.. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-IEC-61557-7 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-IEC-61557-7-TC - Tracked Changes. Electrical safety in low voltage distribution systems up to 1000 V a.c. and 1 500 V d.c. Equipment for testing, measuring or monitoring of protective measures
- BS-EN-IEC-61788-17 - Superconductivity
- BS-EN-IEC-61788-17-TC - Tracked Changes. Superconductivity
- BS-EN-IEC-61788-26 - Superconductivity
- BS-EN-IEC-61788-4 - Superconductivity
- BS-EN-IEC-61788-7 - Superconductivity
- BS-EN-IEC-61869-10 - Instrument transformers
- BS-EN-IEC-61869-11 - Instrument transformers
- BS-EN-IEC-61869-13 - Instrument transformers
- BS-EN-IEC-61869-14 - Instrument transformers
- BS-EN-IEC-61869-15 - Instrument transformers
- BS-EN-IEC-61869-9 - Instrument transformers
- BS-EN-IEC-61869-99 - Instrument transformers
- BS-EN-IEC-62052-11 - Electricity metering equipment. General requirements, tests and test conditions
- BS-EN-IEC-62052-41 - Electricity metering equipment. General requirements, tests and test conditions
- BS-EN-IEC-62053-21 - Electricity metering equipment. Particular requirements
- BS-EN-IEC-62053-22 - Electricity metering equipment. Particular requirements
- BS-EN-IEC-62053-23 - Electricity metering equipment. Particular requirements
- BS-EN-IEC-62053-24 - Electricity metering equipment. Particular requirements
- BS-EN-IEC-62056-3-1 - Electricity metering data exchange. The DLMS/COSEM suite
- BS-EN-IEC-62056-3-1-TC - Tracked Changes. Electricity metering data exchange. The DLMS/COSEM suite
- BS-EN-IEC-62056-6-2 - Electricity metering data exchange. The DLMS/COSEM suite
- BS-EN-IEC-62056-6-2-TC - Tracked Changes. Electricity metering data exchange. The DLMS/COSEM suite
- BS-EN-IEC-62056-8-4 - Electricity metering data exchange. the DLMS/COSEM suite
- BS-EN-IEC-62209-3 - Measurement procedure for the assessment of specific absorption rate of human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices
- BS-EN-IEC-62442-1 - Energy performance of lamp controlgear
- BS-EN-IEC-62442-1-TC - Tracked Changes. Energy performance of lamp controlgear
- BS-EN-IEC-62641 - Conductors for overhead lines. Aluminium and aluminium alloy wires for concentric lay stranded conductors
- BS-EN-IEC/IEEE-62209-1528 - Measurement procedure for the assessment of specific absorption rate of human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices
- BS-EN/IEEE-62704-2 - Determining the peak spatial-average specific absorption rate (SAR) in the human body from wireless communications devices, 30 MHz to 6 GHz
- BS-IEC-60044-8 - Instrument transformers. Electronic current transformers
- BS-IEC-60404-8-5 - Magnetic materials
- BS-IEC-61786-2 - Measurement of DC magnetic, AC magnetic and AC electric fields from 1 Hz to 100 kHz with regard to exposure of human beings
- BS-IEC-62055-41 - Electricity metering. Payment systems
- BS-IEC-62055-41-TC - Tracked Changes. Electricity metering. Payment systems
- BS-IEC-62056-8-5 - Electricity metering data exchange. The DLMS/COSEM suite. Narrow-band OFDM G3-PLC communication profile for neighbourhood networks
- BS-IEC-62233 - Measurement methods for electromagnetic fields of household appliances and similar apparatus with regard to human exposure
- BS-IEC-62792 - Measurement method for the output of electroshock weapons
- BS-IEC/IEEE-62209-1528 - Measurement procedure for the assessment of specific absorption rate of human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices
- BS-IEC/IEEE-62704-1 - Determining the peak spatial-average specific absorption rate (SAR) in the human body from wireless communications devices, 30 MHz to 6 GHz
- BS-IEC/IEEE-62704-2 - Determining the peak spatial-average specific absorption rate (SAR) in the human body from wireless communications devices, 30 MHz to 6 GHz. Specific requirements for finite difference time domain (FDTD) modelling of exposure from vehicle mounted antennas
- BS-IEC/IEEE-62704-3 - Determining the peak spatial-average specific absorption rate (SAR) in the human body from wireless communications devices, 30 MHzto 6 GHz
- BS-IEC/IEEE-62704-4 - Determining the peak spatial-average specific absorption rate (SAR) in the human body from wireless communication devices, 30 MHz to 6 GHz
- BS-IEC/IEEE-63195-1 - Assessment of power density of human exposure to radio frequency fields from wireless devices in close proximity to the head and body (frequency range of 6 GHz to 300 GHz)
- BS-IEC/IEEE-63195-2 - Assessment of power density of human exposure to radio frequency fields from wireless devices in close proximity to the head and body (frequency range of 6 GHz to 300 GHz)
- CWA-16373 - Best practice approach for electromagnetic induction (EMI) measurements of the near surface
- DD-IEC/PAS-60044-5 - Instrument transformers. Capacitor voltage transformers
- DD-IEC/PAS-62260 - Pulse/step return loss from measurement in the frequency domain using the inverse discrete fourier transformation (IDFT)
- DD-IEC/PAS-62338 - Screened balanced cables. Coupling attenuation measurement, triaxial method
- DD-IEC/PAS-62562 - Cavity Resonator Method To Measure the Complex Permittivity of Low-Loss Dielectric Pl
- PD-IEC-61010-3-041 - Safety requirements for electrical equipment for measurement, control, and laboratory use
- PD-IEC-61010-3-042 - Safety requirements for electrical equipment for measurement, control, and laboratory use
- PD-IEC-61869-100 - Instrument transformers
- PD-IEC-61869-102 - Instrument transformers
- PD-IEC-62056-6-9 - Electricity metering data exchange. The DLMS/COSEM suite
- PD-IEC-62056-9-1 - Electricity metering data exchange. The DLMS/COSEM suite
- PD-IEC-62383 - Determination of magnetic loss under magnetic polarization waveforms including higher harmonic components. Measurement, modelling and calculation methods
- PD-IEC-62478 - High voltage test techniques. Measurement of partial discharges by electromagnetic and acoustic methods
- PD-IEC-62689-100 - Current and voltage sensors or detectors, to be used for fault passage indication purposes
- PD-IEC-62764-1 - Measurement procedures of magnetic field levels generated by electronic and electrical equipment in the automotive environment with respect to human exposure
- PD-IEC-62905 - Exposure assessment methods for wireless power transfer systems
- PD-IEC-63167 - Assessment of contact current related to human exposure to electric, magnetic and electromagnetic fields
- PD-IEC-63170 - Measurement procedure for the evaluation of power density related to human exposure to radio frequency fields from wireless communication devices operating between 6 GHz and 100 GHz
- PD-IEC-63213 - Power measurement applications within electrical distribution networks and electrical installations
- PD-IEC-63297 - Sensing devices for non-intrusive load monitoring (NILM) systems
- PD-IEC/PAS-63083 - Specific absorption rate (SAR) measurement procedure for long term evolution (LTE) devices
- PD-IEC/PAS-63151 - Measurement procedure for the assessment of specific absorption rate of human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices. Vector measurement-based systems (Frequency range of 30 MHz to 6 GHz)
IEC:
- IEC-1028 - Electrical measuring instruments - X-Y recorders
- IEC-1028-1 - Amendment No. 1
- IEC-1143-2 - Electrical measuring instruments - X-t recorders - Part 2: Recommended additional test methods
- IEC-1187 - Electrical and electronic measuring equipment - Documentation
- IEC-1580-1 - Methods of measurement for waveguides - Part 1: Decoupling and rotation of the plane of polarization
- IEC-1580-8 - Methods of measurement for waveguides - Part 8: Waveguide power holding capability
- IEC-1580-9 - Methods of measurement for waveguides - Part 9: Reflection coefficient at rectangular waveguide interfaces
- IEC-258 - Direct acting recording electrical measuring instruments and their accessories
- IEC-258-1 - Amendment No. 1
- IEC-428 - Standard cells
- IEC-468 - Method of measurement of resistivity of metallic materials
- IEC-477 - Laboratory resistors. Laboratory d.c. resistors
- IEC-477-2 - Laboratory resistors. Part 2: Laboratory a.c. resistors
- IEC-51-2 - Direct acting indicating analogue electrical measuring instruments and their accessories. Part 2: Special requirements for ammeters and voltmeters
- IEC-51-3 - Direct acting indicating analogue electrical measuring instruments and their accessories. Part 3: Special requirements for wattmeters and varmeters
- IEC-51-3-1 - Amendment No. 1
- IEC-51-4 - Direct acting indicating analogue electrical measuring instruments and their accessories. Part 4: Special requirements for frequency meters
- IEC-51-5 - Direct acting indicating analogue electrical measuring instruments and their accessories. Part 5: Special requirements for phase meters, power factor meters and synchroscopes
- IEC-51-6 - Direct acting indicating analogue electrical measuring instruments and their accessories. Part 6: Special requirements for ohmmeters (impedance meters) and conductance meters
- IEC-51-7 - Direct acting indicating analogue electrical measuring instruments and their accessories. Part 7: Special requirements for multi-function instruments
- IEC-51-8 - Direct acting indicating analogue electrical measuring instruments and their accessories. Part 8: Special requirements for accessories
- IEC-51-9 - Direct acting indicating analogue electrical measuring instruments and their accessories - Part 9: Recommended test methods
- IEC-51-9-1 - Amendment No. 1
- IEC-51-9-2 - Amendment No. 2
- IEC-523 - Direct-current potentiometers
- IEC-523-1 - Amendment No. 1
- IEC-524 - Direct-current resistive volt ratio boxes
- IEC-524-1 - Amendment No. 1
- IEC-564 - D.C. bridges for measuring resistance
- IEC-564-1 - Amendment No. 1
- IEC-60044-1 - Part 1: Current Transformers, Instrument Transformers
- IEC-60044-1-2 - Amendment 2: Instrument Transformers - Part 1: Current Transformers
- IEC-60044-2 - Part 2: Inductive Voltage Transformers, Instrument Transformers
- IEC-60044-2-2 - Amendment 2: Instrument Transformers, Part 2: Inductive Voltage Transformers
- IEC-60044-3 - Part 3: Combined Transformers, Instrument Transformers
- IEC-60044-5 - Part 5: Capacitor Voltage Transformers, Instrument Transformers
- IEC-60044-7 - Instrument transformers - Part 7: Electronic voltage transformers
- IEC-60044-8 - Instrument transformers - Part 8: Electronic current transformers
- IEC-60050-300 - International Electrotechnical Vocabulary - Electrical and electronic measurements and measuring instruments - Part 311: General terms relating to measurements - Part 312: General terms relating to electrical measurements - Part 313: Types of electrical measuring instruments - Part 314: Specific terms according to the type of instrument
- IEC-60050-300-AM1 - Amendment 1 - International Electrotechnical Vocabulary - Electrical and electronic measurements and measuring instruments - Part 312: General terms relating to electrical measurements
- IEC-60050-300-AM2 - Amendment 1 - International electrotechnical vocabulary - Electrical and electronic measurements and measuring instruments - Part 314: Specific terms according to the type of instrument
- IEC-60050-300-AM3 - Amendment 3 - International electrotechnical vocabulary - Electrical and electronic measurements and measuring instruments - Part 314: Specific terms according to the type of instrument
- IEC-60050-300-AM4 - Amendment 4 - International Electrotechnical Vocabulary (IEV) - Part 300: Electrical and electronic measurements and measuring instruments - Part 313: Types of electrical measuring instruments
- IEC-60051-1 - Direct acting indicating analogue electrical measuring instruments and their accessories - Part 1: Definitions and general requirements common to all parts
- IEC-60051-2 - Direct acting indicating analogue electrical measuring instruments and their accessories - Part 2: Special requirements for ammeters and voltmeters
- IEC-60051-3 - Direct acting indicating analogue electrical measuring instruments and their accessories - Part 3: Special requirements for wattmeters and varmeters
- IEC-60051-4 - Direct acting indicating analogue electrical measuring instruments and their accessories title - Part 4: Special requirements for frequency meters
- IEC-60051-5 - Direct acting indicating analogue electrical measuring instruments and their accessories - Part 5: Special requirements for phase meters, power factor meters and synchroscopes
- IEC-60051-6 - Direct acting indicating analogue electrical measuring instruments and their accessories - Part 6: Special requirements for ohmmeters (impedance meters) and conductance meters
- IEC-60051-7 - Direct acting indicating analogue electrical measuring instruments and their accessories - Part 7: Special requirements for multi-function instruments
- IEC-60051-8 - Direct acting indicating analogue electrical measuring instruments and their accessories - Part 8: Special requirements for accessories
- IEC-60060-1 - High-voltage test techniques - Part 1: General definitions and test requirements
- IEC-60060-2 - High-voltage test techniques - Part 2: Measuring systems
- IEC-60060-3 - High-voltage test techniques - Part 3: Definitions and requirements for on-site testing
- IEC-60060 SERIES - High-voltage test techniques - ALL PARTS NEW
- IEC-60060-SERIES - High-voltage test techniques - ALL PARTS
- IEC-60270 - High-voltage test techniques - Partial discharge measurements
- IEC-60270-AM1 - Amendment 1 - High-voltage test techniques - Partial discharge measurements
- IEC-60359 - Electrical and electronic measurement equipment - Expression of performance
- IEC-60404-14 - Magnetic materials - Part 14: Methods of measurement of the magnetic dipole moment of a ferromagnetic material specimen by the withdrawal or rotation method
- IEC-60404-16 - Magnetic materials - Part 16: Methods of measurement of the magnetic properties of Fe-based amorphous strip by means of a single sheet tester
- IEC-60404-17 - Magnetic materials - Part 17: Methods of measurement of the magnetostriction characteristics of grain-oriented electrical steel strip and sheet by means of a single sheet tester and an optical sensor
- IEC-60404-2 - Magnetic materials - Part 2: Methods of measurement of the magnetic properties of electrical steel strip and sheet by means of an Epstein frame
- IEC-60404-2-1 - Amendment 1 - Magnetic materials - Part 2: Methods of measurement of magnetic properties of electrical steel sheet and strip by means of an Epstein frame
- IEC-60404-3 - Magnetic materials - Part 3: Methods of measurement of the magnetic properties of electrical steel strip and sheet by means of a single sheet tester
- IEC-60404-3-1 - Amendment 1
- IEC-60404-3/A2 - Amendment 2 - Magnetic materials - Part 3: Methods of measurement of the magnetic properties of electrical steel strip and sheet by means of a single sheet tester
- IEC-60404-3-RL - Magnetic materials - Part 3: Methods of measurement of the magnetic properties of electrical steel strip and sheet by means of a single sheet tester
- IEC-60404-4 - Magnetic materials - Part 4: Methods of measurement of d.c. magnetic properties of magnetically soft materials
- IEC-60404-4-1 - Amendment 1
- IEC-60404-4-2 - Amendment 2 - Magnetic materials - Part 4: Methods of measurement of d.c. magnetic properties of magnetically soft materials
- IEC-60404-5 - Magnetic materials - Part 5: Permanent magnet (magnetically hard) materials - Methods of measurement of magnetic properties
- IEC-60404-5-1 - Amendment 1 - Magnetic materials - Part 5: Permanent magnet (magnetically hard) materials - Methods of measurement of magnetic properties
- IEC-60404-5-RL - Magnetic materials - Part 5: Permanent magnet (magnetically hard) materials - Methods of measurement of magnetic properties
- IEC-60404-6 - Magnetic materials - Part 6: Methods of measurement of the magnetic properties of magnetically soft metallic and powder materials at frequencies in the range 20 Hz to 100 kHz by the use of ring specimens
- IEC-60404-6-RL - Magnetic materials - Part 6: Methods of measurement of the magnetic properties of magnetically soft metallic and powder materials at frequencies in the range 20 Hz to 100 kHz by the use of ring specimens
- IEC-60404-8-1 - Magnetic materials - Part 8-1: Specifications for individual materials - Magnetically hard materials
- IEC-60404-8-11 - Magnetic materials - Part 8-11: Specifications for individual materials - Fe-based amorphous strip delivered in the semi-processed state
- IEC-60404-8-1-1 - Amendment 1 - Magnetic materials - Part 8-1: Specifications for individual materials - Magnetically hard materials
- IEC-60404-8-2 - Part 8-2: Specifications for Individual Materials - Cold-Rolled Electrical Alloyed Steel S
- IEC-60404-8-3 - Magnetic materials - Part 8-3: Specifications for individual materials - Cold-rolled electrical non-alloyed and alloyed steel sheet and strip delivered in the semi-processed state
- IEC-60404-8-4 - Magnetic materials - Part 8-4: Specifications for individual materials - Cold-rolled non-oriented electrical steel strip and sheet delivered in the fully-processed state
- IEC-60404-8-4-RL - Magnetic materials - Part 8-4: Specifications for individual materials - Cold-rolled non-oriented electrical steel strip and sheet delivered in the fully-processed state
- IEC-60404-8-5 - Magnetic materials - Part 8-5: Specifications for individual materials - Electrical steel strip and sheet with specified mechanical properties and magnetic polarization
- IEC-60469 - Transitions, pulses and related waveforms - Terms, definitions and algorithms
- IEC-60477-1 - Laboratory resistors - Part 1: Laboratory DC resistors
- IEC-60477-2 - Laboratory resistors - Part 2: Laboratory AC resistors
- IEC-60477-2-1 - Amendment No. 1
- IEC-60488-1 - Higher performance protocol for the standard digital interface for programmable instrumentation - Part 1: General
- IEC-60488-2 - Standard digital interface for programmable instrumentation - Part 2: Codes, formats, protocols and common commands
- IEC-60523-2 - Amendment No. 2
- IEC-60524-2 - Amendment No. 2
- IEC-60564-2 - Amendment No. 2
- IEC-60688 - Electrical measuring transducers for converting AC and DC electrical quantities to analogue or digital signals
- IEC-60688-RL - Electrical measuring transducers for converting AC and DC electrical quantities to analogue or digital signals
- IEC-61028-2 - Amendment No. 2
- IEC-61083-1 - Instruments and software used for measurement in high-voltage impulse tests - Part 1: Requirements for instruments
- IEC-61083-2 - Instruments and software used for measurement in high-voltage and high-current tests - Part 2: Requirements for software for tests with impulse voltages and currents
- IEC-61083-3 - Instruments and software used for measurement in high-voltage and high-current tests - Part 3: Requirements for hardware for tests with alternating and direct voltages and currents
- IEC-61143-1 - Electrical measuring instruments - X-t recorders - Part 1: Definitions and requirements
- IEC-61143-1-1 - Amendment No. 1
- IEC-61326-1 - Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 1: General requirements
- IEC-61326-2-1 - Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-1: Particular requirements - Test configurations, operational conditions and performance criteria for sensitive test and measurement equipment for EMC unprotected applications
- IEC-61326-2-1-RL - Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-1: Particular requirements - Test configurations, operational conditions and performance criteria for sensitive test and measurement equipment for EMC unprotected applications
- IEC-61326-2-2 - Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-2: Particular requirements - Test configurations, operational conditions and performance criteria for portable testing, measuring and monitoring equipment used in low-voltage distribution systems
- IEC-61326-2-2-RL - Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-2: Particular requirements - Test configurations, operational conditions and performance criteria for portable testing, measuring and monitoring equipment used in low-voltage distribution systems
- IEC-61326-2-3 - Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-3: Particular requirements - Test configuration, operational conditions and performance criteria for transducers with integrated or remote signal conditioning
- IEC-61326-2-3-RL - Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-3: Particular requirements - Test configuration, operational conditions and performance criteria for transducers with integrated or remote signal conditioning
- IEC-61326-2-4 - Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-4: Particular requirements - Test configurations, operational conditions and performance criteria for insulation monitoring devices according to IEC 61557-8 and for equipment for insulation fault location according to IEC 61557-9
- IEC-61326-2-4-RL - Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-4: Particular requirements - Test configurations, operational conditions and performance criteria for insulation monitoring devices according to IEC 61557-8 and for equipment for insulation fault location according to IEC 61557-9
- IEC-61326-2-5 - Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-5: Particular requirements - Test configurations, operational conditions and performance criteria for field devices with field bus interfaces according to IEC 61784-1
- IEC-61326-2-5-RL - Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-5: Particular requirements - Test configurations, operational conditions and performance criteria for field devices with field bus interfaces according to IEC 61784-1
- IEC-61326-2-6 - Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-6: Particular requirements - In vitro diagnostic (IVD) medical equipment
- IEC-61326-2-6-RL - Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-6: Particular requirements - In vitro diagnostic (IVD) medical equipment
- IEC-61554 - Panel mounted equipment - Electrical measuring instruments - Dimensions for panel mounting
- IEC-61557-1 - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 1: General requirements
- IEC-61557-10 - Electrical safety in low voltage distribution systems up to 1 000 v a.c. and 1 500 v d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 10: Combined measuring equipment for testing, measuring and monitoring of protective measures
- IEC-61557-11 - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 11: Effectiveness of residual current monitors (RCM) in TT, TN and IT systems
- IEC-61557-11-RL - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 11: Effectiveness of residual current monitors (RCM) in TT, TN and IT systems
- IEC-61557-12 - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 12: Power metering and monitoring devices (PMD)
- IEC-61557-12-AM1 - Amendment 1 - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 12: Power metering and monitoring devices (PMD)
- IEC-61557-12-RL - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 12: Power metering and monitoring devices (PMD)
- IEC-61557-13 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 13: Hand-held and hand-manipulated current clamps and sensors for measurement of leakage currents in electrical distribution systems
- IEC-61557-14 - Electrical safety in low voltage distribution systems up to 1 000 V a.c and 1 500 V d.c - Equipment for testing,measuring or monitoring of protective measures - Part 14: Equipment for testing the safety of electrical equipment for machinery
- IEC-61557-15 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 15: Functional safety requirements for insulation monitoring devices in IT systems and equipment for insulation fault location in IT systems
- IEC-61557-16 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c - Equipment for testing, measuring or monitoring of protective measures - Part 16: Equipment for testing the effectiveness of the protective measures of electrical equipment and/or medical electrical equipment
- IEC-61557-17 - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 17: Non-contact AC voltage indicators
- IEC-61557-1-RL - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 1: General requirements
- IEC-61557-2 - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 2: Insulation resistance
- IEC-61557-2-RL - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 2: Insulation resistance
- IEC-61557-3 - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 3: Loop impedance
- IEC-61557-3-RL - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 3: Loop impedance
- IEC-61557-4 - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 4: Resistance of earth connection and equipotential bonding
- IEC-61557-4-RL - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 4: Resistance of earth connection and equipotential bonding
- IEC-61557-5 - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 5: Resistance to earth
- IEC-61557-5-RL - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 5: Resistance to earth
- IEC-61557-6 - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 6: Effectiveness of residual current devices (RCD) in TT, TN and IT systems
- IEC-61557-6-RL - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 6: Effectiveness of residual current devices (RCD) in TT, TN and IT systems
- IEC-61557-7 - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 7: Phase sequence
- IEC-61557-7-RL - Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 7: Phase sequence
- IEC-61557-8 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 8: Insulation monitoring devices for IT systems
- IEC-61566 - Measurement of exposure to radio-frequency electromagnetic fields - Field strength in the frequency range 100 kHz to 1 GHz
- IEC-61580-3 - Methods of measurement for Waveguides - Part 3: Variation of group delay
- IEC-61580-4 - Methods of measurement for waveguides - Part 4: Attenuation of waveguide and waveguide assemblies
- IEC-61786 - Measurement of low-frequency magnetic and electric fields with regard to exposure of human beings - Special requirements for instruments and guidance for measurements
- IEC-61786-1 - Measurement of DC magnetic, AC magnetic and AC electric fields from 1 Hz to 100 kHz with regard to exposure of human beings - Part 1: Requirements for measuring instruments
- IEC-61786-2 - Measurement of DC magnetic, AC magnetic and AC electric fields from 1 Hz to 100 kHz with regard to exposure of human beings - Part 2: Basic standard for measurements
- IEC-61788-16 - Superconductivity - Part 16: Electronic characteristic measurements - Power-dependent surface resistance of superconductors at microwave frequencies
- IEC-61788-17 - Superconductivity - Part 17: Electronic characteristic measurements - Local critical current density and its distribution in large-area superconducting films
- IEC-61788-17-RL - Superconductivity - Part 17: Electronic characteristic measurements - Local critical current density and its distribution in large-area superconducting films
- IEC-61788-26 - Superconductivity - Part 26: Critical current measurement - DC critical current of RE-Ba-Cu-O composite superconductors
- IEC-61788-4 - Superconductivity - Part 4: Residual resistance ratio measurement - Residual resistance ratio of Nb-Ti and Nb3Sn composite superconductors
- IEC-61788-4-RL - Superconductivity - Part 4: Residual resistance ratio measurement - Residual resistance ratio of Nb-Ti and Nb3Sn composite superconductors
- IEC-61788-5 - Superconductivity - Part 5: Matrix to superconductor volume ratio measurement - Copper to superconductor volume ratio of Cu/Nb-Ti composite superconducting wires
- IEC-61788-7 - Superconductivity - Part 7: Electronic characteristic measurements - Surface resistance of high-temperature superconductors at microwave frequencies
- IEC-61788-7-RL - Superconductivity - Part 7: Electronic characteristic measurements - Surface resistance of high-temperature superconductors at microwave frequencies
- IEC-61869-1 - Instrument transformers - Part 1: General requirements
- IEC-61869-10 - Instrument transformers - Part 10: Additional requirements for low-power passive current transformers
- IEC-61869-100 - Instrument transformers - Part 100: Guidance for application of current transformers in power system protection
- IEC-61869-102 - Instrument transformers - Part 102: Ferroresonance oscillations in substations with inductive voltage transformers
- IEC-61869-103 - Instrument transformers - The use of instrument transformers for power quality measurement
- IEC-61869-11 - Instrument transformers - Part 11: Additional requirements for low power passive voltage transformers
- IEC-61869-13 - Instrument transformers - Part 13: Stand-alone merging unit (SAMU)
- IEC-61869-15 - Instrument transformers - Part 15: Additional requirements for voltage transformers for DC applications
- IEC-61869-2 - Instrument transformers - Part 2: Additional requirements for current transformers
- IEC-61869-3 - Instrument transformers - Part 3: Additional requirements for inductive voltage transformers
- IEC-61869-4 - Instrument transformers - Part 4: Additional requirements for combined transformers
- IEC-61869-5 - Instrument transformers - Part 5: Additional requirements for capacitor voltage transformers
- IEC-61869-6 - Instrument transformers - Part 6: Additional general requirements for low-power instrument transformer
- IEC-61869-9 - Instrument transformers - Part 9: Digital interface for instrument transformers
- IEC-61869-99 - Instrument transformers - Part 99: Glossary
- IEC-62004 - Thermal-resistant aluminium alloy wire for overhead line conductor
- IEC-62051-1 - Electricity metering - Data exchange for meter reading, tariff and load control - Glossary of terms - Part 1: Terms related to data exchange with metering equipment using DLMS/COSEM
- IEC-62052-11 - Electricity metering equipment - General requirements, tests and test conditions - Part 11: Metering equipment
- IEC-62052-11-AM1 - Corrigendum 1 - Amendment 1 - Electricity metering equipment (A.C.) - General requirements, tests and test conditions - Part 11: Metering equipment
- IEC-62053-11 - Electricity metering equipment (a.c.) - Particular requirements - Part 11: Electromechanical meters for active energy (classes 0,5, 1 and 2)
- IEC-62053-11-AM1 - Amendment 1 - Electricity metering equipment (a.c.) - Particular requirements - Part 11: Electromechanical meters for active energy (classes 0,5, 1 and 2)
- IEC-62053-21 - Electricity metering equipment - Particular requirements - Part 21: Static meters for AC active energy (classes 0,5, 1 and 2)
- IEC-62053-21-AM1 - Amendment 1 - Electricity metering equipment (a.c.) - Particular requirements - Part 21: Static meters for active energy (classes 1 and 2)
- IEC-62053-22 - Electricity metering equipment - Particular requirements - Part 22: Static meters for AC active energy (classes 0,1S, 0,2S and 0,5S)
- IEC-62053-22-AM1 - Amendment 1 - Electricity metering equipment (a.c.) - Particular requirements - Part 22: Static meters for active energy (classes 0,2 S and 0,5 S)
- IEC-62053-23 - Electricity metering equipment - Particular requirements - Part 23: Static meters for reactive energy (classes 2 and 3)
- IEC-62053-23-AM1 - Amendment 1 - Electricity metering equipment (a.c.) - Particular requirements - Part 23: Static meters for reactive energy (classes 2 and 3)
- IEC-62053-24 - Electricity metering equipment - Particular requirements - Part 24: Static meters for fundamental component reactive energy (classes 0,5S, 1S, 1, 2 and 3)
- IEC-62053-24-AM1 - Amendment 1 - Electricity metering equipment (a.c.) - Particular requirments - Part 24: Static meters for reactive energy at fundamental frequency (classes 0,5 S, 1 S and 1)
- IEC-62053-31 - Electricity metering equipment (a.c.) - Particular requirements - Part 31: Pulse output devices for electromechanical and electronic meters (two wires only)
- IEC-62053-41 - Electricity metering equipment - Particular requirements - Part 41: Static meters for DC energy (classes 0,5 and 1)
- IEC-62053-52 - Electricity metering equipment (AC) - Particular requirements - Part 52: Symbols
- IEC-62055-21 - Electricity metering - Payment systems - Part 21: Framework for standardization
- IEC-62055-41 - Electricity metering - Payment systems - Part 41: Standard transfer specification (STS) - Application layer protocol for one-way token carrier systems
- IEC-62055-41-RL - Electricity metering - Payment systems - Part 41: Standard transfer specification (STS) - Application layer protocol for one-way token carrier systems
- IEC-62055-42 - Electricity metering - Payment systems - Part 42: Transaction Reference Numbers (TRN)
- IEC-62055-52 - Electricity metering - Payment systems - Part 52: Standard transfer specification (STS) - Physical layer protocol for a two-way virtual token carrier for direct local connection
- IEC-62056-1-1 - Electricity metering data exchange - The DLMS/COSEM suite - Part 1-1: Template for DLMS/COSEM communication profile standards
- IEC-62056-21 - Electricity metering - Data exchange for meter reading, tariff and load control - Part 21: Direct local data exchange
- IEC-62056-3-1 - Electricity metering data exchange - The DLMS/COSEM suite - Part 3-1: Use of local area networks on twisted pair with carrier signalling
- IEC-62056-3-1-RL - Electricity metering data exchange - The DLMS/COSEM suite - Part 3-1: Use of local area networks on twisted pair with carrier signalling
- IEC-62056-6-9 - Electricity metering data exchange - The DLMS/COSEM suite - Part 6-9: Mapping between the Common Information Model message profiles (IEC 61968-9) and DLMS/COSEM (IEC 62056) data models and protocols
- IEC-62056-7-3 - Electricity metering data exchange - The DLMS/COSEM suite - Part 7-3: Wired and wireless M-Bus communication profiles for local and neighbourhood networks
- IEC-62056-7-5 - Electricity metering data exchange - The DLMS/COSEM suite - Part 7-5: Local data transmission profiles for Local Networks (LN)
- IEC-62056-8-4 - Electricity metering data exchange - The DLMS/COSEM suite - Part 8-4: Communication profiles for narrow-band OFDM PLC PRIME neighbourhood networks
- IEC-62056-9-1 - Electricity metering data exchange - The DLMS/COSEM suite - Part 9-1: Communication profile using web-services to access a DLMS/COSEM server via a COSEM Access Service (CAS)
- IEC-62110 - Electric and magnetic field levels generated by AC power systems - Measurement procedures with regard to public exposure
- IEC-62226-1 - Exposure to electric or magnetic fields in the low and intermediate frequency range - Methods for calculating the current density and internal electric field induced in the human body - Part 1: General
- IEC-62226-2-1 - Exposure to electric or magnetic fields in the low and intermediate frequency range - Methods for calculating the current density and internal electric field induced in the human body - Part 2-1: Exposure to magnetic fields - 2D models
- IEC-62226-3-1 - Exposure to electric or magnetic fields in the low and intermediate frequency range - Methods for calculating the current density and internal electric field induced in the human body - Part 3-1: Exposure to electric fields - Analytical and 2D numerical models
- IEC-62226-3-1-AM1 - Amendment 1 - Exposure to electric or magnetic fields in the low and intermediate frequency range - Methods for calculating the current density and internal electric field induced in the human body - Part 3-1: Exposure to electric fields - Analytical and 2D numerical models
- IEC-62383 - Determination of magnetic loss under magnetic polarization waveforms including higher harmonic components - Measurement, modelling and calculation methods
- IEC-624 - Expression of the performance of pulse generators
- IEC-62478 - High voltage test techniques - Measurement of partial discharges by electromagnetic and acoustic methods
- IEC-62479 - Assessment of the compliance of low-power electronic and electrical equipment with the basic restrictions related to human exposure to electromagnetic fields (10 MHz to 300 GHz)
- IEC-62586-1 - Power quality measurement in power supply systems - Part 1: Power quality instruments (PQI)
- IEC-62586-2 - Power quality measurement in power supply systems - Part 2: Functional tests and uncertainty requirements
- IEC-62586-2-AM1 - Amendment 1 - Power quality measurement in power supply systems - Part 2: Functional tests and uncertainty requirements
- IEC-62624 - Test methods for measurement of electrical properties of carbon nanotubes
- IEC-62630 - Guidance for evaluating exposure from multiple electromagnetic sources
- IEC-62689-1 - Current and voltage sensors or detectors, to be used for fault passage indication purposes - Part 1: General principles and requirements
- IEC-62689-100 - Current and voltage sensors or detectors, to be used for fault passage indication purposes - Part 100: Requirements and proposals for the IEC 61850 series data model extensions to support fault passage indicators applications
- IEC-62689-2 - Current and voltage sensors or detectors, to be used for fault passage indication purposes - Part 2: System aspects
- IEC-62754 - Computation of waveform parameter uncertainties
- IEC-62764-1 - Measurement procedures of magnetic field levels generated by electronic and electrical equipment in the automotive environment with respect to human exposure - Part 1: Low-frequency magnetic fields
- IEC-62792 - Measurement method for the output of electroshock weapons
- IEC-62905 - Exposure assessment methods for wireless power transfer systems
- IEC-62974-1 - Monitoring and measuring systems used for data collection, gathering and analysis - Part 1: Device requirements
- IEC-63167 - Assessment of contact current related to human exposure to electric, magnetic and electromagnetic fields
- IEC-63170 - Measurement procedure for the evaluation of power density related to human exposure to radio frequency fields from wireless communication devices operating between 6 GHz and 100 GHz
- IEC-63213 - Power measurement applications within electrical distribution networks and electrical installations
- IEC-63297 - Sensing devices for non-intrusive load monitoring (NILM) systems
- IEC-63304 - Methods of measurement of the magnetic properties of permanent magnet (magnetically hard) materials in an open magnetic circuit using a superconducting magnet
- IEC-63377 - Procedures for the assessment of human exposure to electromagnetic fields from radiative wireless power transfer systems . Measurement and computational methods (frequency range of 30 MHz to 300 GHz)
- IEC-63383 - Cybersecurity aspects of devices used for power metering and monitoring, power quality monitoring, data collection and analysis
- IEC-996 - Method for verifying accuracy of tan delta measurements applicable to capacitors
- IEC/IEEE-62209-1528 - Measurement procedure for the assessment of specific absorption rate of human exposure to radio frequency fields from hand-held and body-worn wireless communication devices - Part 1528: Human models, instrumentation and procedures (Frequency range of 4 MHz to 10 GHz)
- IEC/IEEE-62704-1 - Determining the peak spatial-average specific absorption rate (SAR) in the human body from wireless communications devices, 30 MHz to 6 GHz - Part 1: General requirements for using the finite difference time-domain (FDTD) method for SAR calculations
- IEC/IEEE-62704-2 - Determining the peak spatial-average specific absorption rate (SAR) in the human body from wireless communications devices, 30 MHz to 6 GHz - Part 2: Specific requirements for finite difference time domain (FDTD) modelling of exposure from vehicle mounted antennas
- IEC/IEEE-62704-3 - Determining the peak spatial-average specific absorption rate (SAR) in the human body from wireless communications devices, 30 MHz to 6 GHz - Part 3: Specific requirements for using the finite difference time domain (FDTD) method for SAR calculations of mobile phones
- IEC/IEEE-62704-4 - Determining the peak spatial-average specific absorption rate (SAR) in the human body from wireless communication devices, 30 MHz to 6 GHz - Part 4: General requirements for using the finite element method for SAR calculations
- IEC/IEEE-63195-1 - Assessment of power density of human exposure to radio frequency fields from wireless devices in close proximity to the head and body (frequency range of 6 GHz to 300 GHz) - Part 1: Measurement procedure
- IEC/IEEE-63195-2 - Assessment of power density of human exposure to radio frequency fields from wireless devices in close proximity to the head and body (frequency range of 6 GHz to 300 GHz) - Part 2: Computational procedure
- IEC/PAS-60044-5 - Part 5: Capacitor Voltage Transformers - Instrument Transformers
- IEC/PAS-62338 - Screened Balanced Cables - Coupling Attenuation Measurement,Triaxial Method
- IEC/PAS-63083 - Specific absorption rate (SAR) measurement procedure for long term evolution (LTE) devices
- IEC/PAS-63151 - Measurement procedure for the assessment of specific absorption rate ofáhuman exposure to radio frequency fields from hand-held and body-mounted wireless communication devices - Vector measurement-based systems (Frequency range of 30 MHz to 6 GHz)
- IEC/PAS-63184 - Assessment methods of the human exposure to electric and magnetic fields from wireless power transfer systems - Models, instrumentation, measurement and numerical methods and procedures (frequency range of 1 kHz to 30 MHz)
- IEC/PAS-63446 - Conversion method of specific absorption rate to absorbed power density for the assessment of human exposure to radio frequency electromagnetic fields from wireless devices in close proximity to the head and body - Frequency range of 6 GHz to 10 GHz
Other SDOs:
- AS/NZS-5813.1 - Information technology equipment - Energy performance of computers - Methods of measurement of energy performance
- AS/NZS-5813.2 - Information technology equipment - Energy performance of computers - Minimum energy performance standards (MEPS) for computers
- AS/NZS-5814.1 - Information technology equipment - Energy performance of internal power supplies - Methods of measurement of energy performance
- EN-50191 - Erection and operation of electrical test equipment
- EN-50366 - Household & Similar Electrical Appliances, Electromagnetic Fields, Methods for Evaluat
- EN-50383 - Basic standard for the calculation and measurement of electromagnetic field strength and SAR related to human exposure from radio base stations and fixed terminal stations for wireless telecommunication systems (110 MHz - 40 GHz)
- EN-50384 - Product Standard To Demonstrate the Compliance of Radio Base Stations & Fixed Terminal
- EN-50401 - Product standard to demonstrate the compliance of fixed equipment for radio transmission (110 MHz - 40 GHz) intended for use in wireless telecommunication networks with the basic restrictions or the reference levels related to general public exposure to radio frequency electromagnetic fields, when put into service
- EN-50413 - Basic standard on measurement and calculation procedures for human exposure to electric, magnetic and electromagnetic fields (0 Hz - 300 GHz)
- EN-50475 - Basic Standard for the Calculation & the Measurement of Human Exposure To Electromagne
- EN-50476 - Product Standard To Demonstrate the Compliance of Broadcast Station Transmitters With
- EN-50482 - Instrumental Transformers, Three-Phase Inductive Voltage Transformers Having Um Up To
- EN-50492 - Basic standard for the in-situ measurement of electromagnetic field strength related to human exposure in the vicinity of base stations
- EN-50647 - Basic standard for the evaluation of workers' exposure to electric and magnetic fields from equipment and installations for the production, transmission and distribution of electricity
- EN-60051-1 - Direct acting indicating analogue electrical measuring instruments and their accessories - Part 1: Definitions and general requirements common to all parts
- EN-60060-1 - High-voltage test techniques - Part 1: General definitions and test requirements
- EN-60060-2 - High-voltage test techniques - Part 2: Measuring systems
- EN-60060-3 - High Voltage Test Techniques, Definitions & Requirements for On-Site Tests
- EN-60270 - High-voltage test techniques - Partial discharge measurements
- EN-60404-13 - Magnetic Materials, Methods of Measurement of Density, Resistivity & Stacking Factor O
- EN-60404-5 - Magnetic materials - Part 5: Permanent magnet (magnetically hard) materials - Methods of measurement of magnetic properties
- EN-60404-8-1 - Magnetic materials - Part 8-1: Specifications for individual materials - Magnetically hard materials
- EN-60469 - Transitions, pulses and related waveforms - Terms, definitions and algorithms
- EN-60688 - Electrical measuring transducers for converting A.C. and D.C. electrical quantities to analogue or digital signals
- EN-61000-4-30 - Electromagnetic compatibility (EMC) - Part 4-30: Testing and measurement techniques - Power quality measurement methods
- EN-61083-2 - Instruments and software used for measurement in high-voltage and high-current tests - Part 2: Requirements for software for tests with impulse voltages and currents
- EN-61557-1 - Electrical Safety in Low Voltage Distribution Systems Up To 1000 V a.C. & 1500 V D.C.
- EN-61557-10 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 10: Combined measuring equipment for testing, measuring or monitoring of protective measures
- EN-61557-11 - Electrical Safety in Low Voltage Distribution Systems Up To 1000 V a.C. & 1500 V D.C.
- EN-61557-12 - Electrical Safety in Low Voltage Distribution Systems Up To 1000 V a.C. & 1500 V D.C.
- EN-61557-13 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 13: Hand-held and hand-manipulated current clamps and sensors for measurement of leakage currents in electrical distribution systems
- EN-61557-14 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 14: Equipment for testing the safety of electrical equipment of machinery
- EN-61557-15 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 15: Functional safety requirements for insulation monitoring devices in IT systems and equipment for insulation fault location in IT systems
- EN-61557-16 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 16: Equipment for testing the effectiveness of the protective measures of electrical equipment and/or medical electrical equipment
- EN-61557-2 - Electrical Safety in Low Voltage Distribution Systems Up To 1000 V a.C. & 1500 V D.C.
- EN-61557-3 - Electrical Safety in Low Voltage Distribution Systems Up To 1000 V a.C. & 1500 V D.C.
- EN-61557-4 - Electrical Safety in Low Voltage Distribution Systems Up To 1000 V a.C. & 1500 V D.C.
- EN-61557-5 - Electrical Safety in Low Voltage Distribution Systems Up To 1000 V a.C. & 1500 V D.C.
- EN-61557-6 - Electrical Safety in Low Voltage Distribution Systems Up To 1 000 V a.C. & 1 500 V D.
- EN-61557-7 - Electrical Safety in Low Voltage Distribution Systems Up To 1000 V a.C. & 1500 V D.C.
- EN-61557-8 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 8: Insulation monitoring devices for IT systems
- EN-61786-1 - Measurement of DC magnetic, AC magnetic and AC electric fields from 1 Hz to 100 kHz with regard to exposure of human beings - Part 1: Requirements for measuring instruments
- EN-61788-16 - Superconductivity - Part 16: Electronic characteristic measurements - Power-dependent surface resistance of superconductors at microwave frequencies
- EN-61788-17 - Superconductivity - Part 17: Electronic characteristic measurements - Local critical current density and its distribution in large-area superconducting films
- EN-61788-3 - Superconductivity, Critical Current Measurement, Dc Critical Current of AG- &/or Ag Al
- EN-61788-4 - Superconductivity - Part 4: Residual resistance ratio measurement - Residual resistance ratio of Nb-Ti and Nb3Sn composite superconductors
- EN-61788-5 - Superconductivity - Part 5: Matrix to superconductor volume ratio measurement - Copper to superconductor volume ratio of Cu/Nb-Ti composite superconducting wires
- EN-61788-7 - Superconductivity, Electronic Characteristic Measurements, Surface Resistance of Super
- EN-61869-1 - Part 1: General Requirements, Instrument Transformers
- EN-61869-2 - Instrument transformers - Part 2: Additional requirements for current transformers
- EN-61869-3 - Instrument transformers - Part 3: Additional requirements for inductive voltage transformers
- EN-61869-4 - Instrument transformers - Part 4: Additional requirements for combined transformers
- EN-61869-5 - Instrument transformers - Part 5: Additional requirements for capacitor voltage transformers
- EN-61869-6 - Instrument transformers - Part 6: Additional general requirements for low-power instrument transformers
- EN-62052-11 - Electricity metering equipment (AC) - General requirements, tests and test conditions - Part 11: Metering equipment
- EN-62053-11 - Electricity metering equipment (a.c.) - Particular requirements - Part 11: Electromechanical meters for active energy (classes 0,5, 1 and 2)
- EN-62053-21 - Electricity metering equipment (a.c.) - Particular requirements - Part 21: Static meters for active energy (classes 1 and 2)
- EN-62053-22 - Electricity metering equipment (a.c.) - Particular requirements - Part 22: Static meters for active energy (classes 0,2 S and 0,5 S)
- EN-62053-23 - Electricity metering equipment (a.c.) - Particular requirements - Part 23: Static meters for reactive energy (classes 2 and 3)
- EN-62053-24 - Electricity metering equipment (a.c.) - Particular requirements - Part 24: Static meters for reactive energy at fundamental frequency (classes 0,5 S, 1 S and 1)
- EN-62056-7-3 - Electricity metering data exchange - The DLMS/COSEM suite - Part 7-3: Wired and wireless M-Bus communication profiles for local and neighbourhood networks
- EN-62056-7-5 - Electricity metering data exchange - The DLMS/COSEM suite - Part 7-5: Local data transmission profiles for Local Networks (LN)
- EN-62058-11 - Part 11: General Acceptance Inspection Methods, Electricity Metering Equipment (a.C.)
- EN-62058-21 - Part 21: Particular Requirements for Electromechanical Meters for Active Energy (Class
- EN-62058-31 - Part 31: Particular Requirements for Static Meters for Active Energy (Classes 0,2 S, 0
- EN-62110 - Electric & Magnetic Field Levels Generated by Ac Power Systems - Measurement Procedure
- EN-62209-1 - Measurement procedure for the assessment of specific absorption rate of human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices - Part 1: Devices used next to the ear (Frequency range of 300 MHz to 6 GHz)
- EN-62209-2 - Part 2: Procedure To Determine the Specific Absorption Rate (Sar) for Wireless Commun
- EN-62226-3-1 - Exposure to electric or magnetic fields in the low and intermediate frequency range - Methods for calculating the current density and internal electric field induced in the human body - Part 3-1: Exposure to electric fields - Analytical and 2D numerical models
- EN-62233 - Measurement Methods for Electromagnetic Fields of Household Appliances & Similar Appa
- EN-62431 - Reflectivity of Electromagnetic Wave Absorbers in Millimetre Wave Frequency - Measurem
- EN-62479 - Assessment of the compliance of low power electronic and electrical equipment with the basic restrictions related to human exposure to electromagnetic fields (10 MHz to 300 GHz)
- EN-62562 - Cavity resonator method to measure the complex permittivity of low-loss dielectric plates
- EN-62586-1 - Power quality measurement in power supply systems - Part 1: Power quality instruments (PQI)
- EN-62586-2 - Power quality measurement in power supply systems - Part 2: Functional tests and uncertainty requirements
- EN-62689-1 - Current and voltage sensors or detectors, to be used for fault passage indication purposes - Part 1: General principles and requirements
- EN-62689-2 - Current and voltage sensors or detectors, to be used for fault passage indication purposes - Part 2: System aspects
- EN-62754 - Computation of waveform Parameter uncertainties
- EN-62974-1 - Monitoring and measuring systems used for data collection, gathering and analysis - Part 1: Device requirements
- EN-IEC-60051-6 - Direct acting indicating analogue electrical measuring instruments and their accessories - Part 6: Special requirements for ohmmeters (impedance meters) and conductance meters
- EN-IEC-60051-7 - Direct acting indicating analogue electrical measuring instruments and their accessories - Part 7: Special requirements for multi-function instruments
- EN-IEC-60051-8 - Direct acting indicating analogue electrical measuring instruments and their accessories - Part 8: Special requirements for accessories
- EN-IEC-60404-16 - Magnetic materials - Part 16: Methods of measurement of the magnetic properties of Fe-based amorphous strip by means of a single sheet tester
- EN-IEC-60404-6 - Magnetic materials - Part 6: Methods of measurement of the magnetic properties of magnetically soft metallic and powder materials at frequencies in the range 20 Hz to 100 kHz by the use of ring specimens
- EN-IEC-60404-8-11 - Magnetic materials - Part 8-11: Specifications for individual materials - Fe-based amorphous strip delivered in the semi-processed state
- EN-IEC-61869-10 - Instrument transformers - Part 10: Additional requirements for low-power passive current transformers
- EN-IEC-61869-11 - Instrument transformers - Part 11: Additional requirements for low-power passive voltage transformers
- EN-IEC-61869-9 - Instrument transformers - Part 9: Digital interface for instrument transformers (IEC 61869-9:2016)
- EN-IEC-62056-8-4 - Electricity metering data exchange - The DLMS/COSEM suite - Part 8-4: Communication profiles for narrow-band OFDM PLC PRIME neighbourhood networks (IEC 62056-8-4:2018)
- IEC-61869-14 - Instrument transformers - Part 14: Additional requirements for current transformers for DC applications
- JIS-C-0617-8 - Graphical symbols for diagrams -- Part 8: Measuring instruments, lamps and signalling devices
- JIS-C-1102-2 - Direct acting indicating analogue electrical measuring instruments and their accessories Part 2: Special requirements for ammeters and voltmeters
- JIS-C-1102-3 - Direct acting indicating analogue electrical measuring instruments and their accessories Part 3: Special requirements for wattmeters and varmeters
- JIS-C-1102-4 - Direct acting indicating analogue electrical measuring instruments and their accessories Part 4: Special requirements for frequency meters
- JIS-C-1102-5 - Direct acting indicating analogue electrical measuring instruments and their accessories Part 5: Special requirements for phase meters, power factor meters and synchroscopes
- JIS-C-1102-6 - Direct acting indicating analogue electrical measuring instruments and their accessories Part 6: Special requirements for ohmmeters (impedance meters) and conductance meters
- JIS-C-1102-7 - Direct acting indicating analogue electrical measuring instruments and their accessories Part 7: Special requirements for multi-function instruments
- JIS-C-1102-8 - Direct acting indicating analogue electrical measuring instruments and their accessories Part 8: Special requirements for accessories
- JIS-C-1102-9 - Direct acting indicating analogue electrical measuring instruments and their accessories Part 9: Recommended test methods
- JIS-C-1302 - Insulation resistance testers
- JIS-C-1731-1 - Instrument transformetrs for testing purpose and used with general instrument -- Part 1: Current transformers
- JIS-C-1731-2 - Instrument tranformters for testing purpose and used with general instrument -- Part 2: Voltage transformers
- JIS-C-1736 - Instrument transformers for metering service
- JIS-C-2135 - Dry, solid insulating materials -- Resistance test to high-voltage low-current arc discharges
- JIS-H-7305 - Superconductivity -- Part 3: Critical current measurement -- DC critical current of Ag- and/or Ag alloy-sheathed Bi-2212 and Bi-2223 oxide superconductors
- SS-EN-61326-1 - Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 1: General requirements
- SS-EN-61326-2-6 - Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-6: Particular requirements - In vitro diagnostic (IVD) medical equipment