Document Center List of Standards on Vacuum Technology Including Vacuum Pumps
ICS Code 23.160
Return to ICS Index.Up to Level 1:
The following documents are a part of this series:
ASTM:
- ASTM-D4991 - Standard Test Method for Leakage Testing of Empty Rigid Containers by Vacuum Method
- ASTM-E2734 - Standard Specification for Dimensions of Knife-Edge Flanges
- ASTM-E595 - Standard Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environment
- ASTM-E834 - Standard Practice for Determining Vacuum Chamber Gaseous Environment Using a Cold Finger
- ASTM-F2647 - Standard Guide for Approved Methods of Installing a CVS (Central Vacuum System)
BSI:
- BS-5543 - Vacuum technology - graphical symbols
- BS-EN-1012-1 - Compressors and vacuum pumps. Safety requirements
- BS-EN-1012-3 - Compressors and vacuum pumps. Safety requirements
- BS-ISO-14291 - Vacuum gauges. Definitions and specifications for quadrupole mass spectrometers
- BS-ISO-1609 - Vacuum technology. Dimensions of non-knife edge flanges
- BS-ISO-19685 - Vacuum technology. Vacuum gauges. Specifications, calibration and measurement uncertainties for Pirani gauges
- BS-ISO-20146 - Vacuum technology. Vacuum gauges. Specifications, calibration and measurement uncertainties for capacitance diaphragm gauges
- BS-ISO-21358 - Vacuum technology. Right-angle valve. Dimensions and interfaces for pneumatic actuator
- BS-ISO-21358-TC - Tracked Changes. Vacuum technology. Right-angle valve. Dimensions and interfaces for pneumatic actuator
- BS-ISO-21360 - Vacuum technology. Standard methods for measuring vacuum-pump performance. General description
- BS-ISO-21360-1 - Vacuum technology. Standard methods for measuring vacuum-pump performance
- BS-ISO-21360-2 - Vacuum technology. Standard methods for measuring vacuum-pump performance
- BS-ISO-21360-4 - Vacuum technology. Standard methods for measuring vacuum-pump performance
- BS-ISO-21360-6 - Vacuum technology. Standard methods for measuring vacuum-pump performance
- BS-ISO-24477 - Vacuum technology.Vacuum gauges.Specifications, calibration and measurement uncertainties for spinning rotor gauges
- BS-ISO-27892 - Vacuum technology. Turbomolecular pumps. Measurement of rapid shutdown torque
- BS-ISO-27893 - Vacuum technology. Vacuum gauges. Evaluation of the uncertainties of results of calibrations by direct comparison with a reference gauge
- BS-ISO-27894 - Vacuum technology. Vacuum gauges. Specifications for hot cathode ionization gauges
- BS-ISO-27895 - Vacuum technology. Valves. Leak test
- BS-ISO-2861 - Vacuum technology. Dimensions of clamped-type quick-release couplings
- BS-ISO-3529-1 - Vacuum technology. Vocabulary
- BS-ISO-3529-2 - Vacuum technology. Vocabulary
- BS-ISO-3529-3 - Vacuum technology. Vocabulary
- BS-ISO-3567 - Vacuum gauges. Calibration by direct comparison with a reference gauge
- BS-ISO-3669 - Vacuum technology. Dimensions of knife-edge flanges
- BS-ISO-9803-1 - Vacuum technology. Mounting dimensions of pipeline fittings
- BS-ISO-9803-1-TC - Tracked Changes. Vacuum technology. Mounting dimensions of pipeline fittings
- BS-ISO-9803-2 - Vacuum technology. Mounting dimensions of pipeline fittings
- BS-ISO-9803-2-TC - Tracked Changes. Vacuum technology. Mounting dimensions of pipeline fittings
- DD-ISO-3669-2 - Vacuum technology. Bakable flanges
- PD-ISO-20175 - Vacuum technology. Vacuum gauges. Characterization of quadrupole mass spectrometers for partial pressure measurement
- PD-ISO-20177 - Vacuum technology. Vacuum gauges. Procedures to measure and report outgassing rates
- PD-ISO-6737 - Vacuum technology. Vacuum gauges. Characteristics for a stable ionisation vacuum gauge
ISO:
- ISO-14291 - Vacuum gauges - Definitions and specifications for quadrupole mass spectrometers
- ISO-1608-1 - Vapour vacuum pumps -- Measurement of performance characteristics -- Part 1: Measurement of volume rate of flow (pumping speed)
- ISO-1608-2 - Vapour vacuum pumps -- Measurement of performance characteristics -- Part 2: Measurement of critical backing pressure
- ISO-1609 - Vacuum technology - Dimensions of non-knife edge flanges
- ISO-19685 - Vacuum technology - Vacuum gauges - Specifications, calibration and measurement uncertainties for Pirani gauges
- ISO-20146 - Vacuum technology - Vacuum gauges - Specifications, calibration and measurement uncertainties for capacitance diaphragm gauges
- ISO-20175 - Vacuum technology - Vacuum gauges - Characterization of quadrupole mass spectrometers for partial pressure measurement
- ISO-20177 - Vacuum technology - Vacuum gauges - Procedures to measure and report outgassing rates
- ISO-21358 - Vacuum technology - Right-angle valve - Dimensions and interfaces for pneumatic actuator
- ISO-21360 - Vacuum technology - Standard methods for measuring vacuum-pump performance - General description
- ISO-21360-1 - Vacuum technology - Standard methods for measuring vacuum-pump performance - Part 1: General description
- ISO-21360-2 - Vacuum technology - Standard methods for measuring vacuum-pump performance - Part 2: Positive displacement vacuum pumps
- ISO-21360-3 - Vacuum technology - Standard methods for measuring vacuum pump performance - Part 3: Specific parameters for mechanical booster vacuum pumps
- ISO-21360-4 - Vacuum technology - Standard methods for measuring vacuum-pump performance - Part 4: Turbomolecular vacuum pumps
- ISO-21360-5 - Vacuum technology - Standard methods for measuring vacuum-pump performance - Part 5: Non-evaporable getter (NEG) vacuum pumps
- ISO-21360-6 - Vacuum technology - Standard methods for measuring vacuum-pump performance - Part 6: Cryogenic vacuum pumps
- ISO-24477 - Vacuum technology - Vacuum gauges - Specifications, calibration and measurement uncertainties for spinning rotor gauges
- ISO-27892 - Vacuum technology - Turbomolecular pumps - Measurement of rapid shutdown torque
- ISO-27893 - Vacuum technology - Vacuum gauges - Evaluation of the uncertainties of results of calibrations by direct comparison with a reference gauge
- ISO-27894 - Vacuum technology - Vacuum gauges - Specifications for hot cathode ionization gauges
- ISO-27895 - Vacuum technology - Valves - Leak test
- ISO-2861 - Vacuum technology - Dimensions of clamped-type quick-release couplings
- ISO-3529-1 - Vacuum technology - Vocabulary - Part 1: General terms
- ISO-3529-2 - Vacuum technology - Vocabulary - Part 2: Vacuum pumps and related terms
- ISO-3529-3 - Vacuum technology - Vocabulary - Part 3: Total and partial pressure vacuum gauges
- ISO-3530 - Vacuum technology -- Mass-spectrometer-type leak-detector calibration
- ISO-3567 - Vacuum gauges - Calibration by direct comparison with a reference gauge
- ISO-3669 - Vacuum technology - Dimensions of knife-edge flanges
- ISO-3669-2 - Vacuum technology - Bakable flanges - Part 2: Dimensions of knife-edge flanges
- ISO-5302 - Vacuum technology - Turbomolecular pumps - Measurement of performance characteristics
- ISO-6737 - Vacuum technology - Vacuum gauges - Characteristics for a stable ionisation vacuum gauge
- ISO-9803-1 - Vacuum technology - Mounting dimensions of pipeline fittings - Part 1: Non knife-edge flange type
- ISO-9803-2 - Vacuum technology - Mounting dimensions of pipeline fittings - Part 2: Knife-edge flange type
Other SDOs:
- EN-1012-3 - Compressors and vacuum pumps - Safety requirements - Part 3: Process compressors
- JIS-B-2290 - Vacuum technology -- Flange dimensions
- SS-EN-1012-1 - Compressors and vacuum pumps - Safety requirements - Part 1: Air compressors
- SS-EN-1012-2 - Compressors and vacuum pumps - Safety requirements - Part 2: Vacuum pumps
- SS-EN-1012-3 - Compressors and vacuum pumps - Safety requirements - Part 3: Process compressors
- SS-EN-ISO-2151 - Acoustics - Noise test code for compressors and vacuum pumps - Engineering method (Grade 2) (ISO 2151:2004)
- SS-ISO-1607-1 - Positive-displacement vacuum pumps - Measurement of performance characteristics - Part 1: Measurement of volume rate of flow (pumping speed) (ISO 1607-1:1993, IDT)
- SS-ISO-1607-2 - Positive-displacement vacuum pumps - Measurement of performance characteristics - Part 2: Measurement of ultimate pressure
- SS-ISO-8630-3 - Information processing - Data interchange on 130 mm flexible disk cartridges using modified frequency modulation recording at 13262 ftprad, on 80 tracks on each side - Part 3: Track format B for 80 tracks - Teechnical corrigendum 1