Document Center List of Standards on Magnetic Components
ICS Code 29.100.10
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
ASTM:
- ASTM-A1009 - Standard Specification for Soft Magnetic MnZn Ferrite Core Materials for Transformer and Inductor Applications
- ASTM-A1013 - Standard Test Method for High-Frequency (10 kHz-1 MHz) Core Loss of Soft Magnetic Core Components at Controlled Temperatures Using the Voltmeter-Ammeter-Wattmeter Method
- ASTM-A1070 - Standard Specification for Cast and Sintered Alnico Permanent Magnets
- ASTM-A1101 - Standard Specification for Sintered and Fully Dense Neodymium Iron Boron (NdFeB) Permanent Magnets
- ASTM-A1102 - Standard Specification for Sintered Samarium Cobalt (SmCo) Permanent Magnets
- ASTM-A346 - Standard Test Method for Alternating-Current Magnetic Performance of Laminated Core Specimens Using the Dieterly Bridge Method (Withdrawn 1998)
- ASTM-A596 - Standard Test Method for Direct-Current Magnetic Properties of Materials Using the Ballistic Method and Ring Specimens
- ASTM-A598 - Standard Test Method for Magnetic Properties of Magnetic Amplifier Cores
- ASTM-A697 - Standard Test Method for Alternating Current Magnetic Properties of Laminated Core Specimen Using Voltmeter-Ammeter-Wattmeter Methods
- ASTM-A901 - Standard Specification for Amorphous Magnetic Core Alloys, Semi-Processed Types
- ASTM-B715 - Standard Specification for Sintered Copper Structural Parts for Electrical Conductivity Applications
BSI:
- BS-4727-1-GROUP-07 - Glossary of electrotechnical, power, telecommunication, electronics, lighting and colour terms. Terms common to power, telecommunications and electronics
- BS-5336 - Specification. Cores made of ferromagnetic oxides for use in high flux density transformers
- BS-6368 - Specification for axial lead cores made of magnetic oxides or iron powder
- BS-6554-1 - Part 1: Specification for Dimensions, Mechanical Characteristics & Electrical Testing
- BS-6786 - Guide to the specification of limits for physical imperfections of parts made from magnetic oxides
- BS-9925-0 - Harmonized system of quality assessment for electronic components. Inductor and transformer cores for telecommunications. Generic specification
- BS-9925-01.0 - Harmonized system of quality assessment for electronic components. Inductor and transformer cores for telecommunications
- BS-9925-01.01 - Harmonized system of quality assessment for electronic components. Inductor and transformer cores for telecommunications
- BS-9925-02.0 - Harmonized system of quality assessment for electronic components. Inductor and transformer cores for telecommunications
- BS-9925-02.01, 02.02 - Harmonized system of quality assessment for electronic components. Inductor and transformer cores for telecommunications
- BS-9925-03.0 - Harmonized system of quality assessment for electronic components. Inductor and transformer cores for telecommunications
- BS-9925-03.01 - Harmonized system of quality assessment for electronic components. Inductor and transformer cores for telecommunications
- BS-EN-125401 - Harmonized system of quality assessment for electronic components. Blank detail specification. Adjusters used with magnetic oxide (ferrite) cores for use in inductors and tuned transformers
- BS-EN-60133 - Dimensions of pot-cores made of magnetic oxides and associated parts
- BS-EN-60205 - Calculation of the effective parameters of magnetic piece parts
- BS-EN-60401-1 - Terms and nomenclature for cores made of magnetically soft ferrites
- BS-EN-60401-2 - Terms and nomenclature for cores made of magnetically soft ferrite
- BS-EN-60401-3 - Terms and nomenclature for cores made of magnetically soft ferrites
- BS-EN-60424-1 - Ferrite cores. Guidelines on the limits of surface irregularities
- BS-EN-60424-2 - Ferrite cores. Guidelines on the limits of surface irregularities
- BS-EN-60424-3 - Ferrite cores. Guidelines on the limits of surface irregularities
- BS-EN-60424-4 - Ferrite cores. Guidelines on the limits of surface irregularities
- BS-EN-60424-5 - Ferrite cores. Guide on the limits of surface irregularities
- BS-EN-60424-8 - Ferrite cores. Guidelines on the limits of surface irregularities
- BS-EN-60431 - Dimensions of Square Cores (RM-Cores) Made of Magnetic Oxides & Associated Parts, Specific
- BS-EN-60556 - Gyromagnetic materials intended for application at microwave frequencies. Measuring methods for properties
- BS-EN-60740-1 - Laminations for transformers and inductors
- BS-EN-61185 - Ferrite cores (ETD-cores) intended for use in power supply applications. Dimensions
- BS-EN-61332 - Soft ferrite material classification
- BS-EN-61596 - Magnetic oxide EP-cores and associated parts for use in inductors and transformers. Dimensions
- BS-EN-61605 - Fixed inductors for use in electronic and telecommunication equipment. Marking codes
- BS-EN-61843 - Measuring method for the level of intermodulation products generated in a gyromagnetic device
- BS-EN-61860 - Dimension of low-profile cores made of magnetic oxides
- BS-EN-62024-1 - High frequency inductive components. Electrical characteristics and measuring methods. Nanohenry range chip inductor
- BS-EN-62024-2 - High frequency inductive components. Electrical characteristics and measuring methods
- BS-EN-62025-1 - High frequency inductive components. Non-electrical characteristics and measuring methods
- BS-EN-62025-2 - High frequency inductive components. Non-electrical characteristics and measuring methods
- BS-EN-62044-1 - Cores made of soft magnetic materials. Measuring methods
- BS-EN-62044-2 - Cores made of soft magnetic materials. Measuring methods
- BS-EN-62044-3 - Cores made of soft magnetic materials. Measuring methods
- BS-EN-62211 - Inductive components. Reliability management
- BS-EN-62317-1 - Ferrite cores. Dimensions
- BS-EN-62317-11 - Ferrite cores. Dimensions
- BS-EN-62317-12 - Ferrite cores. Dimensions
- BS-EN-62317-13 - Ferrite cores. Dimensions
- BS-EN-62317-2 - Ferrite cores. Dimensions
- BS-EN-62317-4 - Ferrite cores. Dimensions
- BS-EN-62317-5 - Ferrite cores. Dimensions
- BS-EN-62317-6 - Ferrite cores. Dimensions
- BS-EN-62317-7 - Ferrite cores. Dimensions
- BS-EN-62317-8 - Ferrite cores. Dimensions
- BS-EN-62317-9 - Ferrite cores. Dimensions
- BS-EN-62323 - Dimensions of half pot-cores made of ferrite for inductive proximity switches
- BS-EN-62333-1 - Noise suppression sheet for digital devices and equipment
- BS-EN-62333-2 - Noise suppression sheet for digital devices and equipment
- BS-EN-62333-3 - Noise suppression sheet for digital devices and equipment
- BS-EN-62358 - Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS-EN-62674-1 - High frequency inductive components. Fixed surface mount inductors for use in electronic and telecommunication equipment
- BS-EN-IEC-60401-1 - Terms and nomenclature for cores made of magnetically soft ferrites
- BS-EN-IEC-60904-7 - Photovoltaic devices
- BS-EN-IEC-60938-1 - Fixed inductors for electromagnetic interference suppression
- BS-EN-IEC-60938-2-1 - Fixed inductors for electromagnetic interference suppression
- BS-EN-IEC-60938-2-1-TC - Tracked Changes. Fixed inductors for electromagnetic interference suppression
- BS-EN-IEC-61007 - Transformers and inductors for use in electronic and telecommunication equipment. Measuring methods and test procedures
- BS-EN-IEC-61333 - Marking on ferrite cores
- BS-EN-IEC-61631 - Test method for the mechanical strength of cores made of magnetic oxides
- BS-EN-IEC-62024-1 - High frequency inductive components. Electrical characteristics and measuring methods
- BS-EN-IEC-62024-2 - High frequency inductive components. Electrical characteristics and measuring methods
- BS-EN-IEC-62025-2 - High frequency inductive components. Non-electrical characteristics and measuring methods
- BS-EN-IEC-62044-3 - Cores made of soft magnetic materials. Measuring methods
- BS-EN-IEC-62044-3-TC - Tracked Changes. Cores made of soft magnetic materials. Measuring methods
- BS-EN-IEC-63093-1 - Ferrite cores. Guidelines on dimensions and the limits of surface irregularities
- BS-EN-IEC-63093-10 - Ferrite cores. Guidelines on dimensions and the limits of surface irregularities
- BS-EN-IEC-63093-11 - Ferrite cores. Guidelines on dimensions and the limits of surface irregularities
- BS-EN-IEC-63093-12 - Ferrite cores. Guidelines on dimensions and the limits of surface irregularities
- BS-EN-IEC-63093-13 - Ferrite cores. Guidelines on dimensions and the limits of surface irregularities
- BS-EN-IEC-63093-14 - Ferrite cores. Guidelines on dimensions and the limits of surface irregularities
- BS-EN-IEC-63093-2 - Ferrite cores. Guidelines on dimensions and the limits of surface irregularities
- BS-EN-IEC-63093-3 - Ferrite cores. Guidelines on dimensions and the limits of surface irregularities
- BS-EN-IEC-63093-4 - Ferrite cores. Guidelines on dimensions and the limits of surface irregularities
- BS-EN-IEC-63093-5 - Ferrite cores. Guidelines on dimensions and the limits of surface irregularities
- BS-EN-IEC-63093-6 - Ferrite cores. Guidelines on dimensions and the limits of surface irregularities
- BS-EN-IEC-63093-7 - Ferrite cores. Guidelines on dimensions and the limits of surface irregularities
- BS-EN-IEC-63093-8 - Ferrite cores. Guidelines on dimensions and the limits of surface irregularities
- BS-EN-IEC-63182-1 - Magnetic powder cores. Guidelines on dimensions and the limits of surface irregularities
- BS-EN-IEC-63182-2 - Magnetic powder cores. Guidelines on dimensions and the limits of surface irregularities
- BS-EN-IEC-63182-3 - Magnetic powder cores. Guidelines on dimensions and the limits of surface irregularities
- BS-EN-IEC-63182-4 - Magnetic powder cores. Guidelines on dimensions and the limits of surface irregularities
- BS-EN-IEC-63182-5 - Magnetic powder cores. Guidelines on dimensions and the limits of surface irregularities
- BS-EN-IEC-63299 - Classification of magnetic powder cores
- BS-EN-IEC-63300 - Test methods for electrical and magnetic properties of magnetic powder cores
- PD-IEC-63090 - Dimensional tolerances of ferrite cores
- PD-IEC-63307 - Measurement methods of the complex relative permeability and permittivity of noise suppression sheet
IEC:
- IEC-1007 - Transformers and inductors for use in electronic and telecommunication equipment - Measuring methods and test procedures
- IEC-1021-1 - Laminated core packages for transformers and inductors used in telecommunication and electronic equipment - Part 1: Dimensions
- IEC-1021-2 - Laminated core packages for transformers and inductors for use in telecommunication and electronic equipment - Part 2: Electrical characteristics for cores using YEE2 laminations
- IEC-1247 - PM-cores made of magnetic oxides and associated parts - Dimensions
- IEC-1248-1 - Transformers and inductors for use in electronic and telecommunication equipment - Part 1: Generic specification
- IEC-1248-2 - Transformers and inductors for use in electronic and telecommunication equipment - Part 2: Sectional specification for signal transformers on the basis of the capability approval procedure
- IEC-1248-3 - Transformers and inductors for use in electronic and telecommunication equipment - Part 3: Sectional specification for power transformers on the basis of the capability approval procedure
- IEC-1248-4 - Transformers and inductors for use in electronic and telecommunication equipment - Part 4: Sectional specification for power transformers for switched mode power supplies (SMPS) on the basis of the capability approval procedure
- IEC-1248-5 - Transformers and inductors for use in electronic and telecommunication equipment - Part 5: Sectional specification for pulse transformers on the basis of the capability approval procedure
- IEC-1248-6 - Transformers and inductors for use in electronic and telecommunication equipment - Part 6: Sectional specification for inductors on the basis of the capability approval procedure
- IEC-1596 - Magnetic oxide EP-cores and associated parts for use in inductors and transformers - Dimensions
- IEC-1797-1 - Transformers and inductors for use in telecommunication and electronic equipment - Main dimensions of coil formers - Part 1: Coil formers for laminated cores
- IEC-329 - Strip-wound cut cores of grain oriented silicon-iron alloy, used for electronic and telecommunication equipment
- IEC-392 - Guide for the drafting of specifications for microwave ferrites
- IEC-60133 - Dimension of Pot-Cores Made of Magnetic Oxides & Associatedparts
- IEC-60205 - Calculation of the effective parameters of magnetic piece parts
- IEC-60205/A1 - Amendment 1 - Calculation of the effective parameters of magnetic piece parts
- IEC-60401-1 - Terms and nomenclature for cores made of magnetically soft ferrites - Part 1: Terms used for physical irregularities and reference of dimensions
- IEC-60401-1-RL - Terms and nomenclature for cores made of magnetically soft ferrites - Part 1: Terms used for physical irregularities and reference of dimensions
- IEC-60401-2 - Terms and nomenclature for cores made of magnetically soft ferrites - Part 2: Reference of dimensions
- IEC-60401-3 - Terms and nomenclature for cores made of magnetically soft ferrites - Part 3: Guidelines on the format of data appearing in manufacturers catalogues of transformer and inductor cores
- IEC-60424-1 - Ferrite cores - Guidelines on the limits of surface irregularities - Part 1: General specification
- IEC-60424-2 - Ferrite cores - Guidelines on the limits of surface irregularities - Part 2: RM-cores
- IEC-60424-3 - Ferrite cores - Guidelines on the limits of surface irregularities - Part 3: ETD-cores, EER-cores, EC-cores and E-cores
- IEC-60424-4 - Ferrite cores - Guidelines on the limits of surface irregularities - Part 4: Ring-cores
- IEC-60424-5 - Ferrite cores - Guide on the limits of surface irregularities - Part 5: Planar-cores
- IEC-60424-8 - Ferrite cores - Guidelines on the limits of surface irregularities - Part 8: PQ-cores
- IEC-60556 - Gyromagnetic materials intended for application at microwave frequencies - Measuring methods for properties
- IEC-60556-2 - Amendment 2 for IEC-556, Measuring Methods for Properties of Gyromagnetic Materials In
- IEC-60556-AM1 - Amendment 1 - Gyromagnetic materials intended for application at microwave frequencies - Measuring methods for properties
- IEC-60635-1 - Amendment No. 1
- IEC-60670 - General Requirements for Enclosures for Accessories for Household & Similar Fixed Electric
- IEC-60740-1 - Laminations for transformers and inductors - Part 1: Mechanical and electrical characteristics
- IEC-60938-1 - Fixed inductors for electromagnetic interference suppression - Part 1: Generic specification
- IEC-60938-1-1 - Amendment 1 - Fixed inductors for electromagnetic interference suppression - Part 1: Generic specification
- IEC-60938-2 - Fixed inductors for electromagnetic interference suppression - Part 2: Sectional specification on power line chokes
- IEC-60938-2-1 - Fixed inductors for electromagnetic interference suppression - Part 2-1: Blank detail specification - Inductors for which safety tests are required
- IEC-60938-2-2 - Fixed inductors for electromagnetic interference suppression - Part 2-2: Blank detail specification - Inductors for which safety tests are required (only)
- IEC-60938-2-AM 1 - Amendment 1 - Fixed inductors for electromagnetic interference suppression - Part 2: Sectional specification
- IEC-61007 - Transformers and inductors for use in electronic and telecommunication equipment - Measuring methods and test procedures
- IEC-61185 - Ferrite cores (ETD-cores) intended for use in power supply applications - Dimensions
- IEC-61246 - Magnetic Oxide Cores (E-Cores) of Rectangular Cross-Section & Associated Parts - Dime
- IEC-61246-1 - Amendment 1: Magnetic Oxide Cores (E-Cores) of Rectangular Cross-Section and Associated Part
- IEC-61248-7 - Transformers and inductors for use in electronic and telecommunication equipment - Part 7: Sectional specification for high-frequency inductors and intermediate frequency transformers on the basis of the capability approval procedure
- IEC-61332 - Soft ferrite material classification
- IEC-61604 - Dimensions of uncoated ring cores of magnetic oxides
- IEC-61605 - Fixed inductors for use in electronic and telecommunication equipment - Marking codes
- IEC-61631 - Test method for the mechanical strength of cores made of magnetic oxides
- IEC-61631-RL - Test method for the mechanical strength of cores made of magnetic oxides
- IEC-61830 - Microwave Ferrite Components - Measuring Methods for Major Properties
- IEC-61843 - Measuring method for the level of intermodulation products generated in a gyromagnetic device
- IEC-61860 - Dimensions of Low-Profile Cores Made of Magnetic Oxides
- IEC-62024-1 - High frequency inductive components - Electrical characteristics and measuring methods - Part 1: Nanohenry range chip inductor
- IEC-62024-1-RL - High frequency inductive components - Electrical characteristics and measuring methods - Part 1: Nanohenry range chip inductor
- IEC-62024-2 - High frequency inductive components - Electrical characteristics and measuring methods - Part 2: Rated current of inductors for DC-to-DC converters
- IEC-62024-2-RL - High frequency inductive components - Electrical characteristics and measuring methods - Part 2: Rated current of inductors for DC-to-DC converters
- IEC-62025-1 - Part 1: Fixed, Surface Mounted Inductors for Use in Electronic & Telecommunication Equipme
- IEC-62025-2 - High frequency inductive components - Non-electrical characteristics and measuring methods - Part 2: Test methods for non-electrical characteristics
- IEC-62025-2-RL - High frequency inductive components - Non-electrical characteristics and measuring methods - Part 2: Test methods for non-electrical characteristics
- IEC-62044-1 - Cores made of soft magnetic materials - Measuring methods - Part 1: Generic specification
- IEC-62044-2 - Cores made of soft magnetic materials - Measuring methods - Part 2: Magnetic properties at low excitation level
- IEC-62044-3 - Cores made of soft magnetic materials - Measuring methods - Part 3: Magnetic properties at high excitation level
- IEC-62044-3-RL - Cores made of soft magnetic materials - Measuring methods - Part 3: Magnetic properties at high excitation level
- IEC-62211 - Inductive components - Reliability management
- IEC-62317-1 - Ferrite cores - Dimensions - Part 1: General specification
- IEC-62317-11 - Ferrite cores - Dimensions - Part 11: EC-cores for use in power supply applications
- IEC-62317-12 - Ferrite cores - Dimensions - Part 12: Ring cores
- IEC-62317-13 - Ferrite cores - Dimensions - Part 13: PQ-cores for use in power supply applications
- IEC-62317-14 - Ferrite cores - Dimensions - Part 14: EFD-cores for use in power supply applications
- IEC-62317-2 - Ferrite cores - Dimensions - Part 2: Pot-cores for use in telecommunications, power supply, and filter applications
- IEC-62317-4 - Corrigendum 1 - Ferrite cores - Dimensions - Part 4: RM-cores and associated parts
- IEC-62317-5 - Ferrite cores - Dimensions - Part 5: EP-cores and associated parts for use in inductors and transformers
- IEC-62317-6 - Ferrite cores - Dimensions - Part 6: ETD-cores for use in power supplies
- IEC-62317-7 - Ferrite cores - Dimensions - Part 7: EER-cores
- IEC-62317-8 - Ferrite cores - Dimensions - Part 8: E-cores
- IEC-62317-9 - Ferrite cores - Dimensions - Part 9: Planar cores
- IEC-62317-9-1 - Amendment 1 - Ferrite cores - Dimensions - Part 9: Planar cores
- IEC-62323 - Dimensions of half pot-cores made of ferrite for inductive proximity switches
- IEC-62333-1 - Noise suppression sheet for digital devices and equipment - Part 1: Definitions and general properties
- IEC-62333-2 - Noise suppression sheet for digital devices and equipment - Part 2: Measuring methods
- IEC-62333-2-AM1 - Amendment 1 - Noise suppression sheet for digital devices and equipment - Part 2: Measuring methods
- IEC-62333-3 - Noise suppression sheet for digital devices and equipment - Part 3: Characterization of parameters of noise suppression sheet
- IEC-62358 - Ferrite cores - Standard inductance factor for gapped cores and its tolerance
- IEC-62398 - Ferrite cores - Technology approval schedule (TAS)
- IEC-62674-1 - High frequency inductive components - Part 1: Fixed surface mount inductors for use in electronic and telecommunication equipment
- IEC-63090 - Dimensional tolerances of ferrite cores
- IEC-63093-1 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 1: General specification
- IEC-63093-10 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 10: PM-cores and associated parts
- IEC-63093-11 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 11: EC-cores for use in power supply applications
- IEC-63093-12 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 12: Ring-cores
- IEC-63093-13 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 13: PQ-cores
- IEC-63093-14 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 14: EFD-cores
- IEC-63093-2 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 2: Pot-cores for use in telecommunications, power supply, and filter applications
- IEC-63093-3 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 3: Half pot-cores made of ferrite for inductive proximity switches
- IEC-63093-4 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 4: RM-cores
- IEC-63093-5 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 5: EP-cores and associated parts for use in inductors and transformers
- IEC-63093-6 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 6: ETD-cores for use in power supplies
- IEC-63093-7 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 7: EER-cores
- IEC-63093-8 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 8: E-cores
- IEC-63093-9 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 9: Planar cores
- IEC-63182-1 - Magnetic powder cores - Guidelines on dimensions and the limits of surface irregularities - Part 1: General specification
- IEC-63182-2 - Magnetic powder cores - Guidelines on dimensions and the limits of surface irregularities - Part 2: Ring-cores
- IEC-63182-3 - Magnetic powder cores - Guidelines on dimensions and the limits of surface irregularities - Part 3: E-cores
- IEC-63182-4 - Magnetic powder cores - Guidelines on dimensions and the limits of surface irregularities - Part 4: Block-cores
- IEC-63182-5 - Magnetic powder cores - Guidelines on dimensions and the limits of surface irregularities - Part 5: Cylinder-cores
- IEC-63299 - Classification of magnetic powder cores
- IEC-63300 - Test methods for electrical and magnetic properties of magnetic powder cores
- IEC-63307 - Measurement methods of the complex relative permeability and permittivity of noise suppression sheet
- IEC-635 - Toroidal strip-wound cores made of magnetically soft material
- IEC-647 - Dimensions for magnetic oxide cores intended for use in power supplies (EC-cores)
- IEC-732 - Measuring methods for cylinder cores, tube cores and screw cores of magnetic oxides
- IEC-740-2 - Laminations for transformers and inductors for use in telecommunication and electronic equipment - Part 2: Specification for the minimum permeabilities of laminations made of soft magnetic metallic materials
- IEC-852-1 - Outline dimensions of transformers and inductors for use in telecommunication and electronic equipment. Part 1: Transformers and inductors using YEI-1 laminations
- IEC-852-2 - Outline dimensions of transformers and inductors for use in telecommunication and electronic equipment - Part 2: Transformers and inductors using YEx-2 laminations for printed wiring board mounting
- IEC-852-2-ENGLISH/FR - Outline dimensions of transformers and inductors for use in telecommunication and electronic equipment - Part 2: Transformers and inductors using YEx-2 laminations for printed wiring board mounting
- IEC-852-3 - Outline dimensions of transformers and inductors for use in telecommunication and electronic equipment - Part 3: Transformers and inductors using YUI-1 laminations
- IEC-852-4 - Outline dimensions of transformers and inductors for use in telecommunication and electronic equipment - Part 4: Transformers and inductors using YUI-2 laminations
- IEC-852-5 - Outline dimensions of transformers and inductors for use in telecommunication and electronic equipment - Part 5: Transformers and inductors using the series Q of C-cores
- IEC/PAS-62323 - Dimensions of Half Pot Cores Made Magnetic Oxides for Inductive Proximity Switches
Other SDOs:
- BS-EN-IEC-63093-9 - Ferrite cores. Guidelines on dimensions and the limits of surface irregularities
- EN-125401 - Harmonized System of Quality Assessment for Electronic Components, Blank Detail Specif
- EN-60205 - Calculation of the effective parameters of magnetic piece parts
- EN-60401-3 - Terms and nomenclature for cores made of magnetically soft ferrites - Part 3: Guidelines on the format of data appearing in manufacturers catalogues of transformer and inductor cores
- EN-60424-1 - Ferrite cores - Guidelines on the limits of surface irregularities - Part 1: General specification
- EN-60424-2 - Ferrite cores - Guidelines on the limits of surface irregularities - Part 2: RM-cores
- EN-60424-3 - Ferrite cores - Guidelines on the limits of surface irregularities - Part 3: ETD-cores, EER-cores, EC-cores and E-cores
- EN-60424-4 - Ferrite cores - Guidelines on the limits of surface irregularities - Part 4: Ring-cores
- EN-60424-5 - Part 5: Planar-Cores, Ferrite Cores - Guide on the Limits of Surface Irregularities
- EN-60424-8 - Ferrite cores - Guidelines on the limits of surface irregularities - Part 8: PQ-cores
- EN-60556 - Gyromagnetic materials intended for application at microwave frequencies - Measuring methods for properties
- EN-61332 - Soft ferrite material classification
- EN-61596 - Magnetic OXIDEEP-Cores & Associated Parts for Use in Inductors & Transformers, Dimens
- EN-61605 - Fixed inductors for use in electronic and telecommunication equipment - Marking codes
- EN-61843 - Measuring Method for the Level of Intermodulation Products Generated in a Gyromagnetic
- EN-62024-1 - High Frequency Inductive Components, Electrical Characteristics & Measuring Methods, N
- EN-62024-2 - Part 2: Rated Current of Inductors for Dc To Dc Converters, High Frequency Inductive
- EN-62025-1 - High Frequency Inductive Components, Non-Electrical Characteristics & Measuring Method
- EN-62211 - Inductive components - Reliability management
- EN-62317-1 - Ferrite Cores, Dimensions, General Specification
- EN-62317-11 - Ferrite cores - Dimensions - Part 11: EC-cores for use in power supply applications
- EN-62317-12 - Ferrite cores - Dimensions - Part 12: Ring cores
- EN-62317-13 - Ferrite cores - Dimensions - Part 13: PQ-cores for use in power supply applications
- EN-62317-2 - Part 2: Pot-Cores for Use in Telecommunications, Power Supply, & Filter Applications (
- EN-62317-4 - Ferrite Cores, Dimensions, RM-Cores & Associated Parts
- EN-62317-5 - Ferrite cores - Dimensions - Part 5: EP-cores and associated parts for use in inductors and transformers
- EN-62317-6 - Ferrite cores - Dimensions - Part 6: ETD-cores for use in power supplies
- EN-62317-8 - Ferrite Cores, Dimensions, E-Cores
- EN-62317-9 - Ferrite Cores, Dimensions, Planar Cores
- EN-62323 - Dimensions of Half Pot-Cores Made of Ferrite for Inductive Proximity Switches
- EN-62333-2 - Noise suppression sheet for digital devices and equipment - Part 2: Measuring method
- EN-62333-3 - Part 3: Characterization of Parameters of Noise Suppression Sheet, Noise Suppression
- EN-62358 - Ferrite cores - Standard inductance factor for gapped cores and its tolerance
- EN-62674-1 - High frequency inductive components - Part 1: Fixed surface mount inductors for use in electronic and telecommunication equipment
- EN-IEC-62024-1 - High frequency inductive components - Electrical characteristics and measuring methods - Part 1: Nanohenry range chip inductor
- EN-IEC-63093-11 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 11: EC-cores for use in power supply applications
- EN-IEC-63093-12 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 12: Ring-cores (IEC 63093-12:2019)
- EN-IEC-63093-13 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 13: PQ-cores (IEC 63093-13:2019)
- EN-IEC-63093-14 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 14: EFD-cores (IEC 63093-14:2019)
- EN-IEC-63093-4 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 4: RM-cores (IEC 63093-4:2019)
- EN-IEC-63093-5 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 5: EP-cores and associated parts for use in inductors and transformers
- EN-IEC-63093-6 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 6: ETD-cores for use in power supplies
- EN-IEC-63093-7 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 7: EER-cores
- EN-IEC-63093-8 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 8: E-cores
- JIS-C-5064 - Fixed inductors for use in electronic and telecommunication equipment -- Marking codes