Document Center List of Standards on Aluminium And Aluminium Alloys
ICS Code 77.120.10
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
ASTM:
- ASTM-A846 - Standard Specification for Aluminum Scrap for Use in Deoxidation and Alloying of Steel (Withdrawn 2005)
- ASTM-B209M - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric) (Withdrawn 2021)
- ASTM-B308M - Specification for Aluminum-Alloy 6061-T6 Standard Structural Shapes, Rolled or Extruded (Metric) (Withdrawn 1990)
- ASTM-B313M - Specification for Aluminum and Aluminum-Alloy Round Welded Tubes (Metric) (Withdrawn 1990)
- ASTM-B317 - Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor)
- ASTM-B327 - Standard Specification for Master Alloys Used in Making Zinc Die Casting Alloys
- ASTM-B37 - Standard Specification for Aluminum for Use in Iron and Steel Manufacture
- ASTM-B491M - Specification for Aluminum and Aluminum-Alloy Extruded Round Tubes for General Purpose Applications (Metric) (Withdrawn 1990)
- ASTM-B594 - Standard Practice for Ultrasonic Inspection of Aluminum-Alloy Wrought Products
- ASTM-B645 - Standard Practice for Linear-Elastic Plane–Strain Fracture Toughness Testing of Aluminum Alloys
- ASTM-B646 - Standard Practice for Fracture Toughness Testing of Aluminum Alloys
- ASTM-B647 - Standard Test Method for Indentation Hardness of Aluminum Alloys by Means of a Webster Hardness Gage
- ASTM-B648 - Standard Test Method for Indentation Hardness of Aluminum Alloys by Means of a Barcol Impressor
- ASTM-B666M - Practice for Indentification Marking of Aluminum Products (Metric) (Withdrawn 1992)
- ASTM-B724 - Standard Test Method for Indentation Hardness of Aluminum Alloys by Means of a Newage, Portable, Non-Caliper-Type Instrument (Withdrawn 2013)
- ASTM-B807 - Standard Practice for Extrusion Press Solution Heat Treatment for Aluminum Alloys
- ASTM-B921 - Standard Specification for Non-hexavalent Chromium Conversion Coatings on Aluminum and Aluminum Alloys
- ASTM-B926 - Standard Method for Pinhole Determination in Aluminum and Aluminum Alloy Plain Foil by Means of a Light Table
- ASTM-B93M - Specification for Magnesium Alloys Ingot Form for Sand Castings, Permanent Mold Castings, and Die Castings (Metric) (Withdrawn 1990)
- ASTM-B945 - Standard Practice for Aluminum Alloy Extrusions Press Cooled from an Elevated Temperature Shaping Process for Production of T1, T2, T5 and T10–Type Tempers
- ASTM-B989 - Standard Specification for High Fluidity (HF) Zinc-Aluminum Alloy in Ingot Form for Thin Wall Die Castings
- ASTM-B998 - Standard Guide for Hot Isostatic Pressing (HIP) of Aluminum Alloy Castings
- ASTM-D4340 - Standard Test Method for Corrosion of Cast Aluminum Alloys in Engine Coolants Under Heat-Rejecting Conditions
- ASTM-D962 - Standard Specification for Aluminum Powder and Paste Pigments for Paints
- ASTM-E1251 - Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry
- ASTM-E127 - Standard Practice for Fabrication and Control of Aluminum Alloy Ultrasonic Standard Reference Blocks
- ASTM-E1339 - Guide for Identification of Aluminum Alloys and Parts in Computerized Material Property Databases (Withdrawn 1997)
- ASTM-E1793 - Standard Practice for Preparation of Aluminum Alloy for Bonding in Foam and Beam Type Transportable Shelters
- ASTM-E1826 - Standard Specification for Low Volatile Organic Compound (VOC) Corrosion-Inhibiting Adhesive Primer for Aluminum Alloys to Be Adhesively Bonded in Honeycomb Shelter Panels
- ASTM-E227 - Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique (Withdrawn 2002)
- ASTM-E2792 - Standard Test Method for Determination of Hydrogen in Aluminum and Aluminum Alloys by Inert Gas Fusion
- ASTM-E3061 - Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance Based)
- ASTM-E607 - Standard Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere
- ASTM-F3318 - Standard for Additive Manufacturing – Finished Part Properties – Specification for AlSi10Mg with Powder Bed Fusion – Laser Beam
- ASTM-G103 - Standard Practice for Evaluating Stress-Corrosion Cracking Resistance of Low Copper 7XXX Series Al-Zn-Mg-Cu Alloys in Boiling 6 % Sodium Chloride Solution
- ASTM-G110 - Standard Practice for Evaluating Intergranular Corrosion Resistance of Heat Treatable Aluminum Alloys by Immersion in Sodium Chloride + Hydrogen Peroxide Solution
- ASTM-G112 - Standard Guide for Conducting Exfoliation Corrosion Tests in Aluminum Alloys
- ASTM-G34 - Standard Test Method for Exfoliation Corrosion Susceptibility in 2XXX and 7XXX Series Aluminum Alloys (EXCO Test)
- ASTM-G47 - Standard Test Method for Determining Susceptibility to Stress-Corrosion Cracking of 2XXX and 7XXX Aluminum Alloy Products
- ASTM-G64 - Standard Classification of Resistance to Stress-Corrosion Cracking of Heat-Treatable Aluminum Alloys
- ASTM-G66 - Standard Test Method for Visual Assessment of Exfoliation Corrosion Susceptibility of 5XXX Series Aluminum Alloys (ASSET Test)
- ASTM-G67 - Standard Test Method for Determining the Susceptibility to Intergranular Corrosion of 5XXX Series Aluminum Alloys by Mass Loss After Exposure to Nitric Acid (NAMLT Test)
- ASTM-G69 - Standard Test Method for Measurement of Corrosion Potentials of Aluminum Alloys
BSI:
- BS-1470 - Specification for Wrought Aluminium & Aluminium Alloys for General Engineering Purpose
- BS-1728-12 - Methods for the analysis of aluminium and aluminium alloys
- BS-1728-14 - Methods for the analysis of aluminium and aluminium alloys
- BS-1728-15 - Methods for the analysis of aluminium and aluminium alloys
- BS-1728-16 - Methods for the analysis of aluminium and aluminium alloys
- BS-1728-17 - Methods for the analysis of aluminium and aluminium alloys
- BS-1728-18 - Methods for the analysis of aluminium and aluminium alloys
- BS-1728-19 - Methods for the analysis of aluminium and aluminium alloys
- BS-1728-20 - Methods for the analysis of aluminium and aluminium alloys
- BS-1728-21 - Methods for the analysis of aluminium and aluminium alloys
- BS-1728-22 - Methods for the analysis of aluminium and aluminium alloys
- BS-1728-23 - Methods for the analysis of aluminium and aluminium alloys
- BS-1728-24 - Methods for the analysis of aluminium and aluminium alloys
- BS-1728-25 - Methods for the analysis of aluminium and aluminium alloys. Titanium (spectrophotometric chromotropic acid method)
- BS-1728-5 - Methods for the analysis of aluminium and aluminium alloys
- BS-1728-6 - Methods for the analysis of aluminium and aluminium alloys
- BS-1728-8 - Methods for the analysis of aluminium and aluminium alloys
- BS-1728-9 - Methods for the analysis of aluminium and aluminium alloys
- BS-4140-23 - Methods of test for aluminium oxide
- BS-EN-12258-1 - Aluminium and aluminium alloys. Terms and definitions
- BS-EN-12373-1 - Aluminium and aluminium alloys. Anodizing. Method for specifying decorative and protective anodic oxidation coatings on aluminium
- BS-EN-12373-11 - Aluminium and aluminium alloys. Anodizing
- BS-EN-12373-12 - Aluminium and aluminium alloys. Anodizing
- BS-EN-12373-13 - Aluminium and aluminium alloys. Anodizing. Measurement of reflectance characteristics of aluminium surfaces using a goniophotometer or an abridged goniophotometer
- BS-EN-12373-14 - Aluminium and aluminium alloys. Anodizing. Visual determination of image clarity of anodic oxidation coatings. Chart scale method
- BS-EN-12373-15 - Aluminium and aluminium alloys. Anodizing. Assessment of resistance of anodic oxidation coatings to cracking by deformation
- BS-EN-12373-16 - Aluminium and aluminium alloys. Anodizing
- BS-EN-12373-17 - Aluminium and aluminium alloys. Anodizing. Determination of electric breakdown potential
- BS-EN-12373-18 - Aluminium and aluminium alloys. Anodizing. Rating system for the evaluation of pitting corrosion. Chart method
- BS-EN-12373-19 - Aluminium and aluminium alloys. Anodizing. Rating system for the evaluation of pitting corrosion. Grid method
- BS-EN-12373-2 - Aluminium and aluminium alloys. Anodizing. Determination of mass per unit area (surface density) of anodic oxidation coatings. Gravimetric method
- BS-EN-12373-5 - Aluminium and aluminium alloys. Anodizing. Assessment of quality of sealed anodic oxidation coatings by measurement of admittance
- BS-EN-12373-6 - Aluminium and aluminium alloys. Anodizing. Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution without prior acid treatment
- BS-EN-12373-7 - Aluminium and aluminium alloys. Anodizing. Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution with prior acid treatment
- BS-EN-12373-8 - luminium and aluminium alloys. Anodizing. Determination of the comparative fastness to ultra-violet light and heat of coloured anodic oxidation coatings
- BS-EN-12373-9 - Aluminium and aluminium alloys. Anodizing. Measurement of wear resistance and wear index of anodic oxidation coatings using an abrasive wheel wear test apparatus
- BS-EN-12392 - Aluminium and aluminium alloys. Wrought products and cast products. Special requirements for products intended for the production of pressure equipment
- BS-EN-13920-1 - Aluminium and aluminium alloys. Scrap
- BS-EN-13920-10 - Aluminium and aluminium alloys. Scrap
- BS-EN-13920-11 - Aluminium and aluminium alloys. Scrap
- BS-EN-13920-12 - Aluminium and aluminium alloys. Scrap
- BS-EN-13920-13 - Aluminium and aluminium alloys. Scrap
- BS-EN-13920-14 - Aluminium and aluminium alloys. Scrap
- BS-EN-13920-15 - Aluminium and aluminium alloys. Scrap
- BS-EN-13920-2 - Aluminium and aluminium alloys. Scrap
- BS-EN-13920-3 - Aluminium and aluminium alloys. Scrap
- BS-EN-13920-4 - Aluminium and aluminium alloys. Scrap
- BS-EN-13920-5 - Aluminium and aluminium alloys. Scrap
- BS-EN-13920-6 - Aluminium and aluminium alloys. Scrap
- BS-EN-13920-7 - Aluminium and aluminium alloys. Scrap
- BS-EN-13920-8 - Aluminium and aluminium alloys. Scrap
- BS-EN-13920-9 - Aluminium and aluminium alloys. Scrap
- BS-EN-14361 - Aluminium and aluminium alloys. Chemical analysis. Sampling from metal melts
- BS-EN-14726 - Aluminium and aluminium alloys. Determination of the chemical composition of aluminium and aluminium alloys by spark optical emission spectrometry
- BS-EN-515 - Aluminium and aluminium alloys. Wrought products. Temper designations
- BS-EN-573-3 - Aluminium and aluminium alloys. Chemical composition and form of wrought products
- BS-EN-573-4 - Aluminium and aluminium alloys. Chemical composition and form of wrought products
- BS-EN-573-5 - Aluminium and aluminium alloys. Chemical composition and form of wrought products
- BS-EN-575 - Aluminium and aluminium alloys. Master alloys produced by melting. Specifications
- BS-EN-602 - Aluminium and aluminium alloys. Wrought products. Chemical composition of semi-finished products used for the fabrication of articles for use in contact with foodstuff
- BS-EN-683-2-TC - Tracked Changes. Aluminium and aluminium alloys. Finstock
- BS-EN-ISO-2085 - Anodizing of aluminium and its alloys. Check for continuity of thin anodic oxidation coatings. Copper sulfate test
- BS-EN-ISO-2085-TC - Tracked Changes. Anodizing of aluminium and its alloys. Check for continuity of thin anodic oxidation coatings. Copper sulfate test
- BS-EN-ISO-6581 - Anodizing of aluminium and its alloys. Determination of the comparative fastness to ultraviolet light and heat of coloured anodic oxidation coatings
- BS-EN-ISO-6581-TC - Tracked Changes. Anodizing of aluminium and its alloys. Determination of the comparative fastness to ultraviolet light and heat of coloured anodic oxidation coatings
- BS-EN-ISO-8993 - Anodizing of aluminium and its alloys. Rating system for the evaluation of pitting corrosion. Chart method
- BS-ISO-17615 - Aluminium and aluminium alloys. Alloyed ingots for remelting. Specifications
- BS-ISO-2107 - Aluminium and aluminium alloys. Wrought products. Temper designations
- BS-ISO-6279 - Plain bearings. Aluminium alloys for solid bearings
- BS-ISO-6279-TC - Tracked Changes. Plain bearings. Aluminium alloys for solid bearings
- PD-CEN-16748 - Aluminium and aluminium alloys. Mechanical potential of Al-Si alloys for high pressure, low pressure and gravity die casting
- PD-CEN-16749 - Aluminium and aluminium alloys. Classification of Defects and Imperfections in High Pressure, Low Pressure and Gravity Die Cast Products
ISO:
- ISO-1118 - Aluminium and aluminium alloys - Determination of titanium - Spectrophotometric chromotropic acid method
- ISO-115 - Unalloyed aluminium ingots for remelting - Classification and composition
- ISO-17615 - Aluminium and aluminium alloys - Alloyed ingots for remelting - Specifications
- ISO-1784 - Aluminium alloys - Determination of zinc - EDTA titrimetric method
- ISO-20203 - Carbonaceous materials used in the production of aluminium - Calcined coke - Determination of crystallite size of calcined petroleum coke by X-ray diffraction
- ISO-2107 - Aluminium and aluminium alloys - Wrought products - Temper designations
- ISO-2297 - Chemical analysis of aluminium and its alloys - Complexometric determination of magnesium
- ISO-3256 - Aluminium and aluminium alloys - Determination of magnesium - Atomic absorption spectrophotometric method
- ISO-3978 - Aluminium and aluminium alloys - Determination of chromium - Spectrophotometric method using diphenylcarbazide, after extraction
- ISO-3979 - Aluminium and aluminium alloys - Determination of nickel - Spectrophotometric method using dimethylglyoxime
- ISO-3980 - Aluminium and aluminium alloys - Determination of copper - Atomic absorption spectrophotometric method
- ISO-3981 - Aluminium and aluminium alloys - Determination of nickel - Atomic absorption spectrophotometric method
- ISO-4192 - Aluminium and aluminium alloys - Determination of lead content - Flame atomic absorption spectrometric method
- ISO-4193 - Aluminium and aluminium alloys - Determination of chromium content - Flame atomic absorption spectrometric method
- ISO-5194 - Aluminium and aluminium alloys - Determination of zinc content - Flame atomic absorption spectrometric method
- ISO-6827 - Aluminium and aluminium alloys - Determination of titanium content - Diantipyrylmethane photometric method
- ISO-793 - Aluminium and aluminium alloys - Determination of iron - Orthophenanthroline photometric method
- ISO-795 - Aluminium and aluminium alloys - Determination of copper content - Oxalyldihydrazide photometric method
- ISO-796 - Aluminium alloys - Determination of copper - Electrolytic method
- ISO-797 - Aluminium and aluminium alloys - Determination of silicon - Gravimetric method
- ISO-808 - Aluminium and aluminium alloys - Determination of silicon - Spectrophotometric method with the reduced silicomolybdic complex
- ISO-886 - Aluminium and aluminium alloys - Determination of manganese - Photometric method (Manganese content between 0,005 and 1,5 %)
Other SDOs:
- DIN-EN-14242 - Aluminium & Aluminium Alloys - Chemical Analysis, Inductively Coupled Plasma Optical E
- DIN-EN-14361 - Aluminium & Aluminium Alloys - Chemical Analysis, Sampling From Metal Melts
- DIN-EN-14726 - Aluminium & Aluminium Alloys - Chemical Analysis - Guideline for Spark Optical Emissio
- DIN-EN-573-1 - Part 1: Numerical Designation System, Aluminium & Aluminium Alloys - Chemical Composi
- DIN-EN-573-3 - Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products; German version EN 573-3:2013
- DIN-EN-573-4 - Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 4: Forms of products; German version EN 573-4:2004
- EN-12258-1 - Aluminium and aluminium alloys - Terms and definitions - Part 1: General terms
- EN-12373-1 - Part 1: Method for Specifying Decorative & Protective Anodicoxidation Coatings on Alum
- EN-12373-11 - Part 11: Measurement of Specular Reflectance & Specular Gloss of Anodic Oxidation Coat
- EN-12373-12 - Part 12: Measurement of Reflectance Characteristics of Aluminium Sufaces Using Intergr
- EN-12373-13 - Part 13: Measurement of Reflectance Characteristics of Aluminium Surfaces Using a Goni
- EN-12373-14 - Part 14: Visual Determination of Image Clarity of Anodic Oxidation Coatings - Chartsca
- EN-12373-15 - Part 15: Assessment of Resistance of Anodic Oxidation Coatings To Cracking by Deformat
- EN-12373-16 - Part 16: Check for Continuity of Thin Anodic Oxidation Coatings - Aluminium & Aluminiu
- EN-12373-17 - Part 17: Determination of Electric Breakdown Potential, Aluminium & Aluminium Alloys -
- EN-12373-18 - Part 18: Rating System for the Evaluation of Pitting Corrosion - Chart Method, Alumini
- EN-12373-19 - Part 19: Rating System for the Evaluation of Pitting Corrosion - Grid Method, Aluminiu
- EN-12373-2 - Part 2: Determination of Mass per Unit Area (Surface Density) of Anodic Oxidation Coat
- EN-12373-4 - Aluminium & Aluminium Alloys, Anodizing, Estimation of Loss of Absorptive Power of An
- EN-12373-6 - Assessment of Quality of Sealed Anodic Oxidation Coatings by Measurement of the Loss O
- EN-12373-7 - Part 7: Assessment of Quality of Sealed Anodic Oxidation Coatings by Measurement of Th
- EN-12373-8 - Aluminium & Aluminium Alloys, Determination of the Comparative Fastness To Ultra-Viole
- EN-12373-9 - Measurement of Wear Resistance & Wear Index of Anodic Oxidation Coatings Using an Abra
- EN-14242 - Aluminium & Aluminium Alloys - Chemical Analysis, Inductively Coupled Plasma Optical E
- EN-14361 - Aluminium & Aluminium Alloys - Chemical Analysis, Sampling From Metal Melts
- EN-14726 - Aluminium & Aluminium Alloys - Chemical Analysis - Guideline for Spark Optical Emissio
- EN-515 - Aluminium and aluminium alloys - Wrought products - Temper designations
- EN-573-3 - Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products
- EN-573-4 - Part 4: Forms of Products, Aluminium & Aluminium Alloys - Chemical Composition & Form
- EN-573-5 - Part 5: Codification of Standardized Wrought Products, Aluminium & Aluminium Alloys -
- EN-575 - Aluminium & Aluminium Alloys, Master Alloys Produced by Melting, Specifications
- EN-ISO-2085 - Anodizing of Aluminium & Its Alloys - Check for Continuity of Thin Anodic Oxidation Co
- EN-ISO-6581 - Anodizing of Aluminium & Its Alloys - Determination of the Comparative Fastness To Ult
- EN-ISO-8993 - Anodizing of Aluminium & Its Alloys - Rating System for the Evaluation of Pitting Cor
- JIS-G-2402 - Aluminium dross for iron and steel making
- JIS-H-0541 - Method of alkaline salt corrosion testing for magnesium and magnesium alloys
- JIS-H-1352 - Methods for determination of silicon in aluminium and aluminium alloys
- JIS-H-1364 - Methods for determination of bismuth in aluminium and aluminium alloys
- JIS-H-2102 - Aluminium ingots for remelting
- JIS-H-2118 - Aluminium alloy ingots for die castings
- JIS-H-2211 - Aluminium alloy ingots for castings
- JIS-H-8684 - Anodizing of aluminium and its alloys -- Assessment of resistance of anodic oxidation coatings to cracking by deformation
- JIS-H-8711 - Test methods for stress corrosion cracking on aluminium alloys
- MNC-40 - Wrought aluminium and aluminium alloys - Summary
- MNC-41 - Aluminium and aluminium alloys - Slabs. Billets. Ingots. Castings - Summary
- SIS-CEN/TR-16748 - Aluminium and aluminium alloys - Mechanical potential of Al-Si alloys for high pressure, low pressure and gravity die casting
- SIS-CEN/TR-16749 - Aluminium and aluminium alloys - Classification of Defects and Imperfections in High Pressure, Low Pressure and Gravity Die Cast Products
- SS-EN-12258-1 - Aluminium and aluminium alloys - Terms and definitions - Part 1: General terms
- SS-EN-12258-2 - Aluminium and aluminium alloys - Terms and definitions - Part 2: Chemical analysis
- SS-EN-12258-3 - Aluminium and aluminium alloys - Terms and definitions - Part 3: Scrap
- SS-EN-12258-4 - Aluminium and aluminium alloys - Terms and definitions - Part 4: Residues of the aluminium industry
- SS-EN-12373-1 - Aluminium and aluminium alloys - Anodizing - Part 1: Method for specifying decorative and protective anodic oxidation coatings on aluminium
- SS-EN-12373-10 - Aluminium and aluminium alloys - Anodizing - Part 10: Measurement of mean specific abraison resistance of anodic oxidation coatings using an abrasive jet test apparatus
- SS-EN-12373-11 - Aluminium and aluminium alloys - Anodizing - Part 11: Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20º, 45º, 60º or 85º
- SS-EN-12373-12 - Aluminium and aluminium alloys - Anodizing - Part 12: Measurement of reflectance characteristics of aluminium surfaces using integrating-sphere instruments
- SS-EN-12373-13 - Aluminium and aluminium alloys - Anodizing - Part 13: Measurement of reflectance characteristics of aluminium surfaces using a goniophotometer or an abridged goniophotometer
- SS-EN-12373-14 - Aluminium and aluminium alloys - Anodizing - Part 14: Visual determination of image clarity of anodic oxidation coatings - Chart scale method
- SS-EN-12373-15 - Aluminium and aluminium alloys - Anodizing - Part 15: Assessment of resistance of anodic oxidation coatings to cracking by deformation
- SS-EN-12373-16 - Aluminium and aluminium alloys - Anodizing - Part 16: Check for continuity of thin anodic oxidation coatings - Copper sulfate test
- SS-EN-12373-17 - Aluminium and aluminium alloys - Anodizing - Part 17: Determination of electric breakdown potential
- SS-EN-12373-18 - Aluminium and aluminium alloys - Anodizing - Part 18: Rating system for the evaluation of pitting corrosion - Chart method
- SS-EN-12373-19 - Aluminium and aluminium alloys - Anodizing - Part 19: Rating system for the evaluation of pitting corrosion - Grid method
- SS-EN-12373-2 - Aluminium and aluminium alloys - Anodizing - Part 2: Determination of mass per unit area (surface density) of anodic oxidation coatings - Gravimetric method
- SS-EN-12373-3 - Aluminium and aluminium alloys - Anodizing - Part 3: Determination of thickness of anodic oxidation coatings - Non-destructive measurement by split-beam microscope
- SS-EN-12373-4 - Aluminium and aluminium alloys - Anodizing - Part 4: Estimation of loss of absorptive power of anodic oxidation coatings after sealing by dye spot test with prior acid treatment
- SS-EN-12373-5 - Aluminium and aluminium alloys - Anodizing - Part 5: Assessment of quality of sealed anodic oxidation coatings by measurement of admittance
- SS-EN-12373-6 - Aluminium and aluminium alloys - Anodizing - Part 6: Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution without prior acid treatment
- SS-EN-12373-7 - Aluminium and aluminium alloys - Anodizing - Part 7: Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution with prior acid treatment
- SS-EN-12373-8 - Aluminium and aluminium alloys - Anodizing - Part 8: Determination of the comparative fastness to ultra-violet light and heat of coloured anodic oxidation coatings
- SS-EN-12373-9 - Aluminium and aluminium alloys - Anodizing - Part 9: Measurement of wear resistance and wear index of anodic oxidation coatings using an abrasive wheel wear test apparatus
- SS-EN-12392 - Aluminium and aluminium alloys - Wrought products and cast products - Special requirements for products intended for the production of pressure equipment
- SS-EN-1386 - Aluminium and aluminium alloys - Tread plate - Specifications
- SS-EN-13920-1 - Aluminium and aluminium alloys - Scrap - Part 1: General requirements, sampling and tests
- SS-EN-13920-10 - Aluminium and aluminium alloys - Scrap - Part 10: Scrap consisting of used aluminium beverage cans
- SS-EN-13920-11 - Aluminium and aluminium alloys - Scrap - Part 11: Scrap consisting of aluminium-copper radiators
- SS-EN-13920-12 - Aluminium and aluminium alloys - Scrap - Part 12: Turnings consisting of one single alloy
- SS-EN-13920-13 - Aluminium and aluminium alloys - Part 13: Mixed turnings consisting of two or more alloys
- SS-EN-13920-14 - Aluminium and aluminium alloys - Scrap - Part 14: Scrap from post-consumer aluminium packagings
- SS-EN-13920-15 - Aluminium and aluminium alloys - Scrap - Part 15: Decoated aluminium scrap from post-consumer aluminium packagings
- SS-EN-13920-16 - Aluminium and aluminium alloys - Scrap - Part 16: Scrap consisting of skimmings, drosses, spills and metallics
- SS-EN-13920-2 - Aluminium and aluminium alloys - Scrap - Part 2: Unalloyed aluminium scrap
- SS-EN-13920-3 - Aluminium and aluminium alloys - Scrap - Part 3: Wire and cable scrap
- SS-EN-13920-4 - Aluminium and aluminium alloys - Scrap - Part 4: Scrap consisting of one single wrought alloy
- SS-EN-13920-5 - Aluminium and aluminium alloys - Scrap - Part 5: Scrap consisting of two or more wrought alloys of the same series
- SS-EN-13920-6 - Aluminium and aluminium alloys - Scrap - Part 6: Scrap consisting of two or more wrought alloys
- SS-EN-13920-7 - Aluminium and aluminium alloys - Scrap - Part 7: Scrap consisting of castings
- SS-EN-13920-8 - Aluminium and aluminium alloys - Scrap - Part 8: Scrap consisting of non-ferrous materials from shredding processes destined to aluminium separation processes
- SS-EN-13920-9 - Aluminium and aluminium alloys - Scrap - Part 9: Scrap from aluminium separation processes of non-ferrous shredded materials
- SS-EN-14121 - Aluminium and aluminium alloys - Sheet, strip and plate for electrotechnical applications
- SS-EN-14242 - Aluminium and aluminium alloys - Chemical analysis - Inductively coupled plasma optical emission spectrometric analysis
- SS-EN-14361 - Aluminium and aluminium alloys - Chemical analysis - Sampling from metal melts
- SS-EN-14726 - Aluminium and aluminium alloys - Determination of the chemical composition of aluminium and aluminium alloys by spark optical emission spectrometry
- SS-EN-1669 - Aluminium and aluminium alloys - Test methods - Earing test for sheet and strip
- SS-EN-1676 - Aluminium and aluminium alloys - Alloyed ingots for remelting - Specifications
- SS-EN-1706 - Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties
- SS-EN-2284 - Aerospace series - Sulphuric acid anodizing of aluminium and wroughtaluminium alloys
- SS-EN-23134-1 - Light metals and their alloys - Terms and definitions - Part 1: Materials
- SS-EN-23134-2 - Light metals and their alloys - Terms and definitions - Part 2: Unwrought products
- SS-EN-23134-3 - Light metals and their alloys - Terms and definitions - Part 3: Wrought products
- SS-EN-23134-4 - Light metals and their alloys - Terms and definitions - Part 4: Castings
- SS-EN-2536 - Aerospace series - Hard anodizing of aluminium alloys
- SS-EN-485-1 - Aluminium and aluminium alloys - Sheet, strip and plate - Part 1: Technical conditions for inspection and delivery
- SS-EN-485-2 - Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties
- SS-EN-485-3 - Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form for hot-rolled products
- SS-EN-485-4 - Aluminium and aluminium alloys - Sheet, strip andplate - Part 4: Tolerances on shape and dimensions for cold-rolled products
- SS-EN-486 - Aluminium and aluminium alloys - Extrusion ingots - Specifications
- SS-EN-487 - Aluminium and aluminium alloys - Rolling ingots - Specifications
- SS-EN-515 - Aluminium and aluminium alloys - Wrought products - Temper designations
- SS-EN-546-1 - Aluminium and aluminium alloys - Foil - Part 1: Technical conditions for inspection and delivery
- SS-EN-546-2 - Aluminium and aluminium alloys - Foil - Part 2: Mechanical properties
- SS-EN-546-3 - Aluminium and aluminium alloys - Foil - Part 3: Tolerances on dimensions
- SS-EN-546-4 - Aluminium and aluminium alloys - Foil - Part 4: Special property requirements
- SS-EN-570 - Aluminium and aluminium alloys - Impact extrusion slugs obtained from wrought products - Specification
- SS-EN-573-1 - Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 1: Numerical designation system
- SS-EN-573-2 - Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 2: Chemical symbol based designation system
- SS-EN-573-3 - Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products
- SS-EN-573-4 - Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 4: Forms of products
- SS-EN-573-5 - Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 5: Codification of standardized wrought products
- SS-EN-575 - Aluminium and aluminium alloys - Master alloys produced by melting - Specifications
- SS-EN-576 - Aluminium and aluminium alloys - Unalloyed aluminium ingots for remelting - Specifications
- SS-EN-577 - Aluminium and aluminium alloys - Liquid metal - Specifications
- SS-EN-586-2 - Aluminium and aluminium alloys - Forgings - Part 2: Mechanical properties and additional property requirements
- SS-EN-601 - Aluminium and aluminium alloys - Castings - Chemical composition of castings for use in contact with foodstuff
- SS-EN-602 - Aluminium and aluminium alloys - Wrought products - Chemical composition of semi-finished products used for the fabrication of articles for use in contact with foodstuff
- SS-EN-603-1 - Aluminium and aluminium alloys - Wrought forging stock - Part 1: Technical conditions for inspection and delivery
- SS-EN-603-2 - Aluminium and aluminium alloys - Wrought forging stock - Part 2: Mechanical properties
- SS-EN-603-3 - Aluminium and aluminium alloys - Wrought forging stock - Part 3: Tolerances on dimensions and form
- SS-EN-604-1 - Aluminium and aluminium alloys - Cast forging stock - Part 1: Technical conditions for inspection and delivery
- SS-EN-604-2 - Aluminium and aluminium alloys - Cast forging stock - Part 2: Tolerances on dimensions and form
- SS-EN-683-1 - Aluminium and aluminium alloys - Finstock - Part 1: Technical conditions for inspection and delivery
- SS-EN-683-2 - Aluminium and aluminium alloys - Finstock - Part 2: Mechanical properties
- SS-EN-683-3 - Aluminium and aluminium alloys - Finstock - Part 3: Tolerances on dimensions and form
- SS-EN-754-1 - Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 1: Technical conditions for inspection and delivery
- SS-EN-754-2 - Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties
- SS-EN-754-3 - Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 3: Round bars, tolerances on dimensions and form
- SS-EN-754-4 - Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 4: Square bars, tolerances on dimensions and form
- SS-EN-754-5 - Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 5: Rectangular bars, tolerances on dimensions and form
- SS-EN-754-6 - Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 6: Hexagonal bars, tolerances on dimensions and form
- SS-EN-754-7 - Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 7: Seamless tubes, tolerances on dimensions and form
- SS-EN-754-8 - Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 8: Porthole tubes, tolerances on dimensions and form
- SS-EN-755-1 - Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 1: Technical conditions for inspection and delivery
- SS-EN-755-2 - Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 2: Mechanical properties
- SS-EN-755-3 - Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 3: Round bars, tolerances on dimensions and form
- SS-EN-755-4 - Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 4: Square bars, tolerances on dimensions and form
- SS-EN-755-5 - Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 5: Rectangular bars, tolerances on dimensions and form
- SS-EN-755-6 - Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 6: Hexagonal bars, tolerances on dimensions and form
- SS-EN-755-7 - Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 7: Seamless tubes, tolerances on dimensions and form
- SS-EN-755-8 - Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 8: Porthole tubes, tolerances on dimensions and form
- SS-EN-755-9 - Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 9: Profiles, tolerances on dimensions and form
- SS-EN-851 - Aluminium and aluminium alloys - Circle and circle stock for the production of culinary utensils - Specifications
- SS-EN-941 - Aluminium and aluminium alloys - Circle and circle stock for the production of general applications - Specifications
- SS-EN-ISO-10215 - Anodizing of aluminium and its alloys - Visual determination of image clarity of anodic oxidation coatings - Chart scale method (ISO 10215:2018)
- SS-EN-ISO-15496 - Textiles - Measurement of water vapour permeability of textiles for the purpose of quality control (ISO 15496:2018)
- SS-EN-ISO-2085 - Anodizing of aluminium and its alloys - Check for continuity of thin anodic oxidation coatings - Copper sulfate test (ISO 2085:2018)
- SS-EN-ISO-2106 - Anodizing of aluminium and its alloys - Determination of mass per unit area (surface density) of anodic oxidation coatings - Gravimetric method (ISO 2106:2019)
- SS-EN-ISO-2128 - Anodizing of aluminium and its alloys - Determination of thickness of anodic oxidation coatings - Non-destructive measurement by split-beam microscope (ISO 2128:2010)
- SS-EN-ISO-2143 - Anodizing of aluminium and its alloys - Estimation of loss of absorptive power of anodic oxidation coatings after sealing - Dye-spot test with prior acid treatment (ISO 2143:2010)
- SS-EN-ISO-2376 - Anodizing of aluminium and its alloys - Determination of breakdown voltage and withstand voltage (ISO 2376:2019)
- SS-EN-ISO-2931 - Anodizing of aluminium and its alloys - Assessment of quality of sealed anodic oxidation coatings by measurement of admittance (ISO 2931:2017)
- SS-EN-ISO-3210 - Anodizing of aluminium and its alloys - Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in acid solution(s) (ISO 3210:2017)
- SS-EN-ISO-3211 - Anodizing of aluminium and its alloys - Assessment of resistance of anodic oxidation coatings to cracking by deformation (ISO 3211:2018)
- SS-EN-ISO-6581 - Anodizing of aluminium and its alloys - Determination of the comparative fastness to ultraviolet light and heat of coloured anodic oxidation coatings (ISO 6581:2018)
- SS-EN-ISO-6719 - Anodizing of aluminium and its alloys - Measurement of reflectance characteristics of aluminium surfaces using integrating-sphere instruments (ISO 6719:2010)
- SS-EN-ISO-7599 - Anodizing of aluminium and its alloys - Method for specifying decorative and protective anodic oxidation coatings on aluminium (ISO 7599:2018)
- SS-EN-ISO-7668 - Anodizing of aluminium and its alloys - Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20°, 45°, 60° or 85° (ISO 7668:2021)
- SS-EN-ISO-7759 - Anodizing of aluminium and its alloys - Measurement of reflectance characteristics of aluminium surfaces using a goniophotometer or an abridged goniophotometer (ISO 7759:2010)
- SS-EN-ISO-8251 - Anodizing of aluminium and its alloys - Measurement of abrasion resistance of anodic oxidation coatings (ISO 8251:2018)
- SS-EN-ISO-8434-1 - Metallic tube connections for fluid power and general use - Part 1: 24° cone connectors (ISO 8434-1:2018)
- SS-EN-ISO-8434-4 - Metallic tube connections for fluid power and general use - Part 4: 24o cone connectors with O-ring weld-on nipples (ISO 8434-4:1995)
- SS-EN-ISO-8993 - Anodizing of aluminium and its alloys - Rating system for the evaluation of pitting corrosion - Chart method (ISO 8993:2018)
- SS-EN-ISO-9974-2 - Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 2: Stud ends with elastomeric sealing (type E) (ISO 9974-2:1996)
- SS-EN-ISO-9974-3 - Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 3: Stud ends with metal-or-metal sealing (type B) (ISO 9974-3:1996)
- SS-ENV-1967 - Structural adhesives - Evaluation of the effectiveness of surface treatment techniques for aluminium using a wet peel test in association with the floating roller method
- SS-ISO-10546 - Chemical conversion coatings - Rinsed and non-rinsed chromate conversion coatings on aluminium and alloys
- SS-ISO-2106 - Anodizing of aluminium and its alloys - Determination of mass per unit area (surface density) of anodic oxide coatings - Gravimetric method
- SS-ISO-2128 - Anodizing of aluminium and its alloys - Determination of thickness of anodic oxide coatings - Non-destructive measurement by split-beam microscope
- SS-ISO-2135 - Anodizing of aluminium and its alloys - Accelerated test of light fastness of coloured anodic oxidecoatings using artificial light
- SS-ISO-2143 - Anodizing of aluminium and its alloys - Estimation of loss of absorptive power of anodic oxide coatings after sealing - Dye spot test with prior acidtreatment
- SS-ISO-2376 - Anodization (anodic oxidation) of aluminium and its alloys - Insulation check by measurement of breakdown potential
- SS-ISO-2931 - Anodizing of aluminium and its alloys - Assessment of quality of sealed anodic oxide coatings by measurement of admittance or impedance
- SS-ISO-3210 - Anodizing of aluminium and its alloys - Assessment of quality of sealed anodic coatings by measurement of the loss of mass after immersion in phosphoric-chromic acid solution
- SS-ISO-5190 - Anodizing of aluminium and its alloys - Evaluation of uniformity of appearance of architectural anodic finishes - Determination of diffuse reflectance and specular gloss
- SS-ISO-6279 - Plain bearings - Aluminium alloys for solid bearings (ISO 6279:2006, IDT)
- SS-ISO-6581 - Anodizing of aluminium and its alloys - Determination of the fastness to ultra violet light to coloured anodic oxide coatings
- SS-ISO-6719 - Anodized aluminium and its alloys - Measurements of reflectance characteristics of aluminium surfaces using integrating-sphere instruments
- SS-ISO-7583 - Anodizing of aluminium and its alloys - Vocabulary
- SS-ISO-7599 - Anodizing of aluminium and its alloys - General specifications for anodic oxide coatings on aluminium
- SS-ISO-7668 - Anodized aluminium and aluminium alloys - Measurements of specular reflectance and specular gloss at angles of 20 degrees, 45 degrees, 60 degrees or 85 degrees
- SS-ISO-7669 - Anodized aluminium and its alloys - Measurements of total reflectivity using a photoelectric reflectometer
- SS-ISO-7759 - Anodizing of aluminium and its alloys - Measurements of reflectivity characteristics of aluminium surfaces using abridged goniophotometer or goniophotometer
- SS-ISO-8076 - Aerospace process - Anodic treatment of aluminiumalloys - Chromic acid process 40 V DC, undyed coating
- SS-ISO-8077 - Aerospace process - Anodic treatment of aluminiumalloys - Chromic acid process 20 V DC, undyed coating
- SS-ISO-8078 - Aerospace process - Anodic treatment of aluminium alloys - Sulfuric acid process, undyed coating
- SS-ISO-8079 - Aerospace process - Anodic treatment of aluminiumalloys - Sulfuric acid process, dyed coating
- SS-ISO-8080 - Aerospace - Anodic treatment of titanium and titanium alloys - Sulfuric acid process
- SS-ISO-8081 - Aerospace process - Chemical conversion coating for aluminium alloys - General purpose
- SS-ISO-8251 - Anodized aluminium and aluminium alloys - Measurements of wear resistance and wear index of anodic oxidation coatings with an abrasive wheel wear test apparatus
- SS-ISO-8252 - Anodized aluminium and aluminium alloys - Measurements of mean specific abrasion resistance of anodic oxidation coatings with an abrasive jet test apparatus
- UNE-38114 - Wrought aluminium and aluminium alloys. 1000 series. Al. Alloy EN AW-1050 A/EN AW-Al 99,5
- UNE-38115 - Wrought aluminium and aluminium alloys. 1000 series. Al. Alloy EN AW-1200/EN AW-Al 99,0.
- UNE-38117 - Wrought aluminium and aluminium alloys. 1000 series. Al. Alloy EN AW-1070 A/EN AW-Al 99,7.
- UNE-38312 - Wrought aluminium and aluminium alloys. 2000 series. AlCu. Alloy EN AW-2017A, EN AW-AlCu4MgSi(A).
- UNE-38313 - Wrought aluminium and aluminium alloys. 2000 series. AlCu. Alloy EN AW-2014/EN AW-AlCu4SiMg.
- UNE-38314 - Wrought aluminium and aluminium alloys. 2000 series. AlCu. Alloy EN AW-2024, EN AW-AlCu4Mg1.
- UNE-38336 - Wrought aluminium and aluminium alloys. 5000 series. AlMg. Alloy EN AW-5052/EN AW-AlMg2,5
- UNE-38339 - Wrought aluminium and aluminium alloys. 5000 series. AlMg. Alloy EN AW-5754/EN AW-AlMg3.
- UNE-38340 - Wrought aluminium and aluminium alloys. 5000 series. AlMg. Alloy EN AW-5083/EN AW-AlMg4,5Mn0,7
- UNE-38342 - Wrought aluminium and aluminium alloys. 6000 series. AlMgSi. Alloy EN AW-6061/EN AW-AlMg1SiCu.