Document Center List of Standards on Rubber And Plastics Products Moulding Or Extrusion Products Should Be Classified According To Specific Products Transmission Belts, See 21.220.10 Conveyor Belts, See 53.040.20 Rubber And Plastics Coated Fabrics, See 59.080.40 Footwear, See 61.060 Tyres, See 83.160
ICS Code 83.140
Return to ICS Index.Up to Level 1:
Down to Level 3:
- 83.140.01 (Rubber and plastics products in general)
- 83.140.10 (Films and sheets Including plates)
- 83.140.20 (Laminated sheets)
- 83.140.30 (Plastics pipes and fittings for non fluid use Plastics pipes, fittings and valves for general use, see 23.040.20, 23.040.45 and 23.060)
- 83.140.40 (Hoses Hoses for general use, see 23.040.70)
- 83.140.50 (Seals Seals for general use, see 21.140 and 23.040.80)
- 83.140.99 (Other rubber and plastics products)
The following documents are a part of this series:
BSI:
Other SDOs:
- SS-EN-12229 - Surfaces for sports areas - Procedure for the preparation of synthetic turf and needle-punch test pieces
- SS-EN-1734 - Rubber- or plastics coated fabrics - Determination of resistance to water penetration - Low pressure method
- SS-EN-1735 - Rubber- or plastics coated fabrics - Determination of flexibility
- SS-EN-1847 - Flexible sheets for waterproofing - Plastics and rubber sheets for roof waterproofing - Methods for exposure to liquid chemicals, including water
- SS-EN-2155-7 - Aerospace series - Test methods for transparent materials for aircraft glazing - Part 7: Determination of optical deviation
- SS-EN-438-1 - High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 1: Introduction and general information
- SS-EN-438-2 - High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 2: Determination of properties
- SS-EN-477 - Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of the resistance to impact of profiles by falling mass
- SS-EN-478 - Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of the appearance after exposure at 150 °C
- SS-EN-479 - Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of heat reversion
- SS-EN-ISO-11963 - Plastics - Polycarbonate sheets - Types, dimensions and characteristics (ISO 11963:2019)
- SS-EN-ISO-12017 - Plastics - Poly(methyl methacrylate) double- and triple-skin sheets - Test methods (ISO 12017:2021)
- SS-EN-ISO-14631 - Extruded sheets of impact-modified polystyrene (PS-I) - Requirements and test methods (ISO 14631:2021)
- SS-EN-ISO-15013 - Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods (ISO 15013:2022)
- SS-EN-ISO-2231 - Rubber- or plastics-coated fabrics - Standard atmospheres for conditioning and testing (ISO 2231:1989)
- SS-EN-ISO-4674-1 - Rubber- or plastics-coated fabrics - Determination of tear resistance - Part 1: Constant rate of tear methods (ISO 4674-1:2016)
- SS-EN-ISO-527-3 - Plastics - Determination of tensile properties - Part 3: Test conditions for films and sheets (ISO 527-3:2018)
- SS-ENV-1186-1 - Materials and articles in contact with foodstuffs- Plastics - Part 1: Guide to the selection of conditions and test methods for overall migration
- SS-ENV-1186-10 - Materials and articles in contact with foodstuffs- Plastics - Part 10: Test method for overall migration into olive oil (modified method for use in case where incompete extraction of olive oil occurs)
- SS-ENV-1186-2 - Materials and articles in contact with foodstuffs- Plastics - Part 2:Test method for overall migration into olive oil by total immersion
- SS-ENV-1186-3 - Materials and articels in contact with foodstuffs- Plastics - Part 3: Test methods for overall migration into aqueous simulants by total immersion
- SS-ENV-1186-4 - Materials and articles in contact with foodstuffs- Plastics - Part 4: Test methods for overall migration into olive oil by cell
- SS-ENV-1186-5 - Materials and articles in contact with foodstuffs- Plastics - Part 5: Test methods for overall migration into aqueous food simulant by cell
- SS-ENV-1186-6 - Materials and articles in contact with foodstuffs- Plastics - Part 6: Test methods for overall migration into olive oil using a pouch
- SS-ENV-1186-7 - Materials and articles in contact with foodstuffs- Plastics - Part 7: Test methods for overall migration into aqueous simulant using a pouch
- SS-ENV-1186-8 - Materials and articles in contact with foodstuffs- Plastics - Part 8: Test methods for overall migration into olive oil by article filling
- SS-ENV-1186-9 - Materiels and articles in contact with foodstuffs- Plastics - Part 9: Test methods for overall migration into aqueous food simulant by article filling
- SS-ISO-1167 - Plastic pipes for the transport of fluids - Determination of the resistance to internal pressure
- SS-ISO-4586-1 - High-pressure decorative laminates - Sheets made from thermosetting resins - Part 1: Classification and specifications (ISO 4586-1:2004, IDT)
- SS-ISO-4586-2 - High-pressure decorative laminates - Sheets made from thermosetting resins - Part 2: Determination of properties (ISO 4586-2:2004, IDT)
- SS-ISO-7267-3 - Rubber-covered rollers - Determination of apparent hardness - Part 3: Pusey and Jones method (ISO 7267-3:2017, IDT)
- SS-ISO-7313 - Aircraft - High temperature convoluted hose assemblies in polytetrafluoroethylene (PTFE)
- SS-ISO-8233 - Thermoplastic valves - Torque - Test method
- SS-ISO-8829 - Aerospace - Polytetrafluoroethylene (PTFE) hose assemblies - Test methods