Document Center List of Standards on Concrete Structures Including The Repair And Protection Of Concrete Products And Structures
ICS Code 91.080.40
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
ASTM:
- ASTM-A1044 - Standard Specification for Steel Stud Assemblies for Shear Reinforcement of Concrete
- ASTM-C1138M - Standard Test Method for Abrasion Resistance of Concrete (Underwater Method)
- ASTM-C1262 - Standard Test Method for Evaluating the Freeze-Thaw Durability of Dry-Cast Segmental Retaining Wall Units and Related Concrete Units
- ASTM-C1542 - Standard Test Method for Measuring Length of Concrete Cores
- ASTM-C1583 - Standard Test Method for Tensile Strength of Concrete Surfaces and the Bond Strength or Tensile Strength of Concrete Repair and Overlay Materials by Direct Tension (Pull-off Method)
- ASTM-C1602 - Standard Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete
- ASTM-C1603 - Standard Test Method for Measurement of Solids in Water
- ASTM-C1645 - Standard Test Method for Freeze-thaw and De-icing Salt Durability of Solid Concrete Interlocking Paving Units
- ASTM-D4070 - Standard Specification for Adhesive Lubricant for Installation of Preformed Elastomeric Bridge Compression Seals in Concrete Structures
- ASTM-D4258 - Standard Practice for Surface Cleaning Concrete for Coating
- ASTM-D4259 - Standard Practice for Preparation of Concrete by Abrasion Prior to Coating Application
- ASTM-D4260 - Standard Practice for Liquid and Gelled Acid Etching of Concrete
- ASTM-D4261 - Standard Practice for Surface Cleaning Concrete Masonry Units for Coating
- ASTM-D4262 - Standard Test Method for pH of Chemically Cleaned or Etched Concrete Surfaces
- ASTM-D4263 - Standard Practice for Indicating Moisture in Concrete by the Plastic Sheet Method
- ASTM-D5295 - Standard Guide for Preparation of Concrete Surfaces for Adhered (Bonded) Membrane Waterproofing Systems
- ASTM-D6087 - Standard Test Method for Evaluating Asphalt-Covered Concrete Bridge Decks Using Ground Penetrating Radar
- ASTM-D6760 - Standard Test Method for Integrity Testing of Concrete Deep Foundations by Ultrasonic Crosshole Testing
- ASTM-D7088 - Standard Practice for Resistance to Hydrostatic Pressure for Coatings Used in Below Grade Applications Applied to Masonry
- ASTM-D7234 - Standard Test Method for Pull-Off Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers
- ASTM-D7635 - Standard Test Method for Measurement of Thickness of Coatings Over Fabric Reinforcement
- ASTM-D7682 - Standard Test Method for Replication and Measurement of Concrete Surface Profiles Using Replica Putty
- ASTM-D7705 - Standard Test Method for Alkali Resistance of Fiber Reinforced Polymer (FRP) Matrix Composite Bars used in Concrete Construction
- ASTM-D7853 - Standard Test Method for Hydraulic Pullout Resistance of a Geomembrane with Locking Extensions Embedded in Concrete
- ASTM-D7913 - Standard Test Method for Bond Strength of Fiber-Reinforced Polymer Matrix Composite Bars to Concrete by Pullout Testing
- ASTM-D7914 - Standard Test Method for Strength of Fiber Reinforced Polymer (FRP) Bent Bars in Bend Locations
- ASTM-D7949 - Standard Test Methods for Thermal Integrity Profiling of Concrete Deep Foundations (Withdrawn 2023)
- ASTM-E1399 - Standard Test Method for Cyclic Movement and Measuring the Minimum and Maximum Joint Widths of Architectural Joint Systems
- ASTM-E1966 - Standard Test Method for Fire-Resistive Joint Systems
- ASTM-E2170 - Standard Test Method for Determining Anaerobic Biodegradation Potential of Organic Chemicals Under Methanogenic Conditions (Withdrawn 2013)
- ASTM-F2170 - Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
- ASTM-G109 - Standard Test Method for Determining Effects of Chemical Admixtures on Corrosion of Embedded Steel Reinforcement in Concrete Exposed to Chloride Environments
BSI:
- BS-2691 - Steel wire for prestressed concrete
- BS-3617 - Seven-wire steel strand for prestressed concrete
- BS-4449 - Steel for the reinforcement of concrete. Weldable reinforcing steel. Bar, coil and decoiled product. Specification
- BS-4466 - Specification for Scheduling, Dimensioning, Bending and Cutting of Steel Reinforcement
- BS-4482 - Steel wire for the reinforcement of concrete products. Specification
- BS-4483 - Steel fabric for the reinforcement of concrete. Specification
- BS-4486 - Specification for hot rolled and hot rolled and processed high tensile alloy steel bars for the prestressing of concrete
- BS-5896 - High tensile steel wire and strand for the prestressing of concrete. Specification
- BS-6089 - Assessment of in-situ compressive strength in structures and precast concrete components. Complementary guidance to that given in BS EN 13791
- BS-6744 - Stainless steel bars. Reinforcement of concrete. Requirements and test methods
- BS-8110-1 - Structural use of concrete. Code of practice for design and construction
- BS-8110-2 - Structural use of concrete. Code of practice for special circumstances
- BS-8110-3 - Structural use of concrete. Design charts for singly reinforced beams, doubly reinforced beams and rectangular columns
- BS-8539 - Code of practice for the selection and installation of post-installed anchors in concrete and masonry
- BS-8666 - Scheduling, dimensioning, bending and cutting of steel reinforcement for concrete. Specification
- BS-8666-TC - Tracked Changes. Scheduling, dimensioning, bending and cutting of steel reinforcement for concrete. Specification
- BS-EN-12188 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of adhesion steel-to-steel for characterization of structural bonding agents
- BS-EN-12189 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of open time
- BS-EN-12192-1 - Products and systems for the protection and repair of concrete structures. Granulometry analysis
- BS-EN-12192-2 - Products and systems for the protection and repair of concrete structures. Granulometry analysis
- BS-EN-12269-1 - Determination of the bond behaviour between reinforcing steel and autoclaved aerated concrete by the 'beam test'
- BS-EN-12269-2 - Determination of the bond behaviour between reinforcing steel and autoclaved aerated concrete by the beam test
- BS-EN-12614 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of glass transition temperatures of polymers
- BS-EN-12615 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of slant shear strength
- BS-EN-12617-1 - Products and systems for the protection and repair of concrete structures. Test methods
- BS-EN-12617-2 - Products and systems for the protection and repair of concrete structures. Test methods
- BS-EN-12617-3 - Products and systems for the protection and repair of concrete structures. Test methods
- BS-EN-12617-4 - Products and systems for the protection and repair of concrete structures. Test methods
- BS-EN-12618-2 - Products and systems for the protection and repair of concrete structures. Test methods
- BS-EN-12618-3 - Products and systems for the protection and repair of concrete structures. Test methods
- BS-EN-12636 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of adhesion concrete to concrete
- BS-EN-12696 - Cathodic protection of steel in concrete
- BS-EN-13057 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of resistance of capillary absorption
- BS-EN-13294 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of stiffening time
- BS-EN-13381-3 - Test methods for determining the contribution to the fire resistance of structural members
- BS-EN-13391 - Mechanical tests for post-tensioning systems
- BS-EN-13395-1 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of workability
- BS-EN-13395-2 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of workability
- BS-EN-13395-3 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of workability
- BS-EN-13395-4 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of workability
- BS-EN-13412 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of modulus of elasticity in compression
- BS-EN-13579 - Products and systems for the protection and repair of concrete structures. Test methods. Drying test for hydrophobic impregnation
- BS-EN-13580 - Products and systems for the protection and repair of concrete structures. Test methods. Water absorption and resistance to alkali for hydrophobic impregnations
- BS-EN-13581 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of loss of mass of hydrophobic impregnated concrete after freeze-thaw salt stress
- BS-EN-13670 - Execution of concrete structures
- BS-EN-13687-1 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of thermal compatibility
- BS-EN-13687-2 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of thermal compatibility
- BS-EN-13687-3 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of thermal compatibility
- BS-EN-13687-4 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of thermal compatibility
- BS-EN-13687-5 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of thermal compatibility
- BS-EN-13733 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of the durability of structural bonding agents
- BS-EN-13791 - Assessment of in-situ compressive strength in structures and precast concrete components
- BS-EN-13894-2 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of fatigue under dynamic loading
- BS-EN-14038-1 - Electrochemical realkalization and chloride extraction treatments for reinforced concrete
- BS-EN-14038-1-TC - Tracked Changes. Electrochemical realkalization and chloride extraction treatments for reinforced concrete
- BS-EN-14038-2 - Electrochemical realkalization and chloride extraction treatments for reinforced concrete
- BS-EN-14038-2-TC - Tracked Changes. Electrochemical realkalization and chloride extraction treatments for reinforced concrete
- BS-EN-14497 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of the filtration stability
- BS-EN-14498 - Products and systems for the protection and repair of concrete structures. Test methods. Volume and weight changes of injection products after air drying and water storage cycles
- BS-EN-1504-1 - Products and systems for the protection and repair of concrete structures. Definitions, requirements, quality control and evaluation of conformity
- BS-EN-1504-10 - Products and systems for the protection and repair of concrete structures. Definitions, requirements, quality control and evaluation of conformity
- BS-EN-1504-10-TC - Tracked Changes. Products and systems for the protection and repair of concrete structures. Definitions, requirements, quality control and evaluation of conformity
- BS-EN-1504-2 - Products and systems for the protection and repair of concrete structures. Definitions, requirements, quality control and evaluation of conformity
- BS-EN-1504-3 - Products and systems for the protection and repair of concrete structures. Definitions, requirements, quality control and evaluation of conformity
- BS-EN-1504-5 - Products and systems for the protection and repair of concrete structures. Definitions, requirements, quality control and evaluation of conformity
- BS-EN-1504-6 - Products and systems for the protection and repair of concrete structures. Definitions, requirements, quality control and evaluation of conformity
- BS-EN-1504-7 - Products and systems for the protection and repair of concrete structures. Definitions, requirements, quality control and evaluation of conformity
- BS-EN-1504-8 - Products and systems for the protection and repair of concrete structures. Definitions, requirements, quality control and AVCP
- BS-EN-1504-8-TC - Tracked Changes. Products and systems for the protection and repair of concrete structures. Definitions, requirements, quality control and AVCP
- BS-EN-1504-9 - Products and systems for the protection and repair of concrete structures. Definitions, requirements, quality control and evaluation of conformity
- BS-EN-15183 - Products and systems for the protection and repair of concrete structures. Test methods. Corrosion protection test
- BS-EN-15184 - Products and systems for the protection and repair of concrete structures. Test methods. Shear adhesion of coated steel to concrete (pull-out test)
- BS-EN-1766 - Products and systems for the protection and repair of concrete structures. Test methods. Reference concretes for testing
- BS-EN-1766-TC - Tracked Changes. Products and systems for the protection and repair of concrete structures. Test methods. Reference concretes for testing
- BS-EN-1767 - Products and systems for the protection and repair of concrete structures. Test methods. Infrared analysis
- BS-EN-1771 - Products and systems for the protection and repair of concrete structures. Test methods. Determination of injectability and splitting test
- BS-EN-1877-1 - Products and systems for the protection and repair of concrete structures. Test methods. Reactive functions related to epoxy resins
- BS-EN-1877-2 - Products and systems for the protection and repair of concrete structures. Test methods. Reactive functions related to epoxy resins. Determination of amine functions using the total basicity number
- BS-EN-1992-1-1 - Eurocode 2. Design of concrete structures
- BS-EN-1992-1-1(NA) - UK National Annex to Eurocode 2. Design of concrete structures. General rules and rules for buildings
- BS-EN-1992-1-2 - Eurocode 2. Design of concrete structures
- BS-EN-1992-1-2(NA) - UK National Annex to Eurocode 2. Design of concrete structures
- BS-EN-1992-2 - Eurocode 2. Design of concrete structures
- BS-EN-1992-2(NA) - UK National Annex to Eurocode 2. Design of concrete structures
- BS-EN-1992-3 - Eurocode 2. Design of concrete structures
- BS-EN-1992-3(NA) - UK National Annex to Eurocode 2. Design of concrete structures
- BS-EN-1992-4 - Eurocode 2. Design of concrete structures
- BS-EN-1994-1-1 - Eurocode 4. Design of composite steel and concrete structures
- BS-EN-1994-1-1(NA) - UK National Annex to Eurocode 4. Design of composite steel and concrete structures
- BS-EN-1994-1-2 - Eurocode 4. Design of composite steel and concrete structures
- BS-EN-1994-1-2(NA) - UK National Annex to Eurocode 4. Design of composite steel and concrete structures
- BS-EN-1994-2 - Eurocode 4. Design of composite steel and concrete structures
- BS-EN-524-1 - Steel strip sheaths for prestressing tendons. Test methods
- BS-EN-524-2 - Steel strip sheaths for prestressing tendons. Test methods
- BS-EN-524-3 - Steel strip sheaths for prestressing tendons. Test methods
- BS-EN-524-4 - Steel strip sheaths for prestressing tendons. Test methods
- BS-EN-524-5 - Steel strip sheaths for prestressing tendons. Test methods
- BS-EN-524-6 - Steel strip sheaths for prestressing tendons. Test methods
- BS-EN-ISO-12696 - Cathodic protection of steel in concrete
- BS-EN-ISO-12696-TC - Tracked Changes. Cathodic protection of steel in concrete
- BS-ISO-10144 - Steels for the reinforcement and prestressing of concrete. Certification scheme for steel bars and wires
- BS-ISO-13270 - Steel fibres for concrete. Definitions and specifications
- BS-ISO-13315-1 - Environmental management for concrete and concrete structure
- BS-ISO-13315-3 - Environmental management for concrete and concrete structures.Production of concrete constituents and concrete.
- BS-ISO-13315-8 - Environmental management for concrete and concrete structures
- BS-ISO-16836 - Non-destructive testing. Acoustic emission testing. Measurement method for acoustic emission signals in concrete
- BS-ISO-16837 - Non-destructive testing. Acoustic emission testing. Test method for damage qualification of reinforced concrete beams
- BS-ISO-16838 - Non-destructive testing. Acoustic emission testing. Test method for classification of active cracks in concrete structures
- BS-ISO-19338 - Performance and assessment requirements for design standards on structural concrete
- BS-ISO-22040 - Life cycle management of concrete structures
- BS-ISO-22040-2 - Life cycle management of concrete structures
- BS-ISO-5091-1 - Structural intervention of existing concrete structures using cementitious materials
- BS-ISO-5091-2 - Structural intervention of existing concrete structures using cementitious materials
- BS-ISO-5091-3 - Structural intervention of existing concrete structures using cementitious materials
- BS-ISO-5091-4 - Structural intervention of existing concrete structures using cementitious materials
- BS-ISO-6934-4 - Steel for the prestressing of concrete
- BS-ISO-9607-1 - Paints and varnishes. Protective coatings for concrete structures
- CWA-14646 - Requirements for the Installation of Post-Tensioning Kits for Prestressting of Structu
- DD-CEN-14038-1 - Electrochemical realkalization and chloride extraction treatments for reinforced concrete
- DD-CEN-1992-4-1 - Design of fastenings for use in concrete
- DD-CEN-1992-4-2 - Design of fastenings for use in concrete
- DD-CEN-1992-4-3 - Design of fastenings for use in concrete
- DD-CEN-1992-4-4 - Design of fastenings for use in concrete
- DD-CEN-1992-4-5 - Design of fastenings for use in concrete
- DD-ENV-13670-1 - Execution of concrete structures
- DD-ENV-1504-9 - Products and systems for the protection and repair of concrete structures. Definitions, requirements, quality control andevaluation of conformity
- DD-ENV-1992-1-1 - Eurocode 2. Design of concrete structures
- DD-ENV-1992-1-3 - Eurocode 2. Design of concrete structures
- DD-ENV-1992-1-4 - Eurocode 2. Design of concrete structures. General rules. Lightweight aggregate concrete with closed structure (together with United Kingdom National Application Document)
- DD-ENV-1992-1-5 - Eurocode 2. Design of concrete structures. General rules. Structures with unbonded and external prestressing tendons (together with United Kingdom National Application Document)
- DD-ENV-1992-1-6 - Eurocode 2. Design of concrete structures. General rules. Plain concrete structures
- DD-ENV-1992-2 - Eurocode 2: Design of Concrete Structures, Concrete Bridges
- DD-ENV-1992-4 - Eurocode 2. Design of concrete structures
- KIT-182 - Be-En-1992-1-2 & Uk National Annex Kit, Eurocode 2, Design of Concrete Structures, Gen
- KIT-184 - BS-En-1992-1-1 & Uk National Annex Kit, Eurocode 2, Design of Concrete Structures, Gen
- KIT-206 - Design of Concrete Structures
- KIT-208 - Design on Composite Steel & Concrete Structures
- PD-6687 - Background Paper To the Uk National Annexes To BS-En-1992-1
- PD-6687-2 - Recommendations for the design of structures to BS EN 1992-2:2005
- PD-6696-2 - Background paper to BS EN 1994-2 and the UK National Annex to BS EN 1994-2
- PD-CEN-15177 - Testing the freeze-thaw resistance of concrete. Internal structural damage
- PD-CEN-17079 - Design of fastenings for use in concrete. Redundant non-structural systems
- PD-CEN-17080 - Design of fastenings for use in concrete. Anchor channels. Supplementary rules
- PD-CEN-17081 - Design of fastenings for use in concrete. Plastic design of fastenings with headed and post-installed fasteners
- PD-CEN-17086 - Further guidance on the application of EN 13791:2019 and background to the provisions
- PD-CEN-19103 - Eurocode 5. Design of Timber Structures. Structural design of timber-concrete composite structures. Common rules and rules for buildings
- PD-ISO-16475 - General practices for the repair of water-leakage cracks in concrete structures
- PD-ISO-16774-2 - Test methods for repair materials for water-leakage cracks in underground concrete structures
- PD-ISO-16774-3 - Test methods for repair materials for water-leakage cracks in underground concrete structures
- PD-ISO-16774-4 - Test methods for repair materials for water-leakage cracks in underground concrete structures
- PD-ISO-16774-5 - Test methods for repair materials for water-leakage cracks in underground concrete structures
- PD-ISO-16774-6 - Test methods for repair materials for water-leakage cracks in underground concrete structures
ISO:
- ISO-10144 - Steels for the reinforcement and prestressing of concrete - Certification scheme for steel bars and wires
- ISO-10287 - Steel for the reinforcement of concrete -- Determination of strength of joints in welded fabric
- ISO-10544 - Cold-reduced steel wire for the reinforcement of concrete and the manufacture of welded fabric
- ISO-10606 - Steel for the reinforcement of concrete -- Determination of percentage total elongation at maximum force
- ISO-11082 - Certification scheme for welded fabric for the reinforcement of concrete structures
- ISO-13270 - Steel fibres for concrete - Definitions and specifications
- ISO-13315-1 - Environmental management for concrete and concrete structures - Part 1: General principles
- ISO-13315-2 - Environmental management for concrete and concrete structures - Part 2: System boundary and inventory data
- ISO-13315-3 - Environmental management for concrete and concrete structures - Part 3: Production of concrete constituents and concrete
- ISO-13315-4 - Environmental management for concrete and concrete structures - Part 4: Environmental design of concrete structures
- ISO-13315-6 - Environmental management for concrete and concrete structures - Part 6: Use of concrete structures
- ISO-13315-8 - Environmental management for concrete and concrete structures - Part 8: Environmental labels and declarations
- ISO-14484 - Performance guidelines for design of concrete structures using fibre-reinforced polymer (FRP) materials
- ISO-14654 - Epoxy-coated steel for the reinforcement of concrete
- ISO-14655 - Epoxy-coated strand for the prestressing of concrete
- ISO-14656 - Epoxy powder and sealing material for the coating of steel for the reinforcement of concrete
- ISO-14657 - Zinc-coated steel for the reinforcement of concrete
- ISO-15673 - Guidelines for the simplified design of structural reinforced concrete for buildings
- ISO-16204 - Durability - Service life design of concrete structures
- ISO-16475 - General practices for the repair of water-leakage cracks in concrete structures
- ISO-16774-1 - Test methods for repair materials for water-leakage cracks in underground concrete structures - Part 1: Test method for thermal stability
- ISO-16774-2 - Test methods for repair materials for water-leakage cracks in underground concrete structures - Part 2: Test method for chemical resistance
- ISO-16774-3 - Test methods for repair materials for water-leakage cracks in underground concrete structures - Part 3: Test method for water (wash out) resistance
- ISO-16774-4 - Test methods for repair materials for water-leakage cracks in underground concrete structures - Part 4: Test method for adhesion on wet concrete surface
- ISO-16774-5 - Test methods for repair materials for water-leakage cracks in underground concrete structures - Part 5: Test method for watertightness
- ISO-16774-6 - Test methods for repair materials for water-leakage cracks in underground concrete structures - Part 6: Test method for response to the substrate movement
- ISO-16836 - Non-destructive testing - Acoustic emission testing - Measurement method for acoustic emission signals in concrete
- ISO-16837 - Non-destructive testing - Acoustic emission testing - Test method for damage qualification of reinforced concrete beams
- ISO-16838 - Non-destructive testing - Acoustic emission testing - Test method for classification of active cracks in concrete structures
- ISO-18319 - Fibre-reinforced polymer (FRP) reinforcement for concrete structures - Specifications of FRP sheets
- ISO-18319-2 - Fibre reinforced polymer (FRP) reinforcement for concrete structures - Part 2: Specifications of CFRP strips
- ISO-18407 - Simplified design of prestressed concrete tanks for potable water
- ISO-18408 - Simplified structural design for reinforced concrete wall buildings
- ISO-19338 - Performance and assessment requirements for design standards on structural concrete
- ISO-20987 - Simplified design for mechanical connections between precast concrete structural elements in buildings
- ISO-21725-1 - Simplified design of prestressed concrete bridges - Part 1: I-girder bridges
- ISO-21725-2 - Simplified design of prestressed concrete bridges - Part 2: Box-girder bridges
- ISO-22040 - Life cycle management of concrete structures
- ISO-22040-2 - Life cycle management of concrete structures - Part 2: Structural planning and design stage
- ISO-22966 - Execution of concrete structures
- ISO-28841 - Guidelines for simplified seismic assessment and rehabilitation of concrete buildings
- ISO-28842 - Guidelines for simplified design of reinforced concrete bridges
- ISO-5091-1 - Structural intervention of existing concrete structures using cementitious materials - Part 1: General principles
- ISO-5091-2 - Structural intervention of existing concrete structures using cementitious materials - Part 2: Top surface overlaying
- ISO-5091-3 - Structural intervention of existing concrete structures using cementitious materials - Part 3: Bottom-surface (soffit) underlaying
- ISO-5091-4 - Structural intervention of existing concrete structures using cementitious materials - Part 4: Jacketing
- ISO-6934-1 - Steel for the prestressing of concrete - Part 1: General requirements
- ISO-6934-2 - Steel for the prestressing of concrete - Part 2: Cold-drawn wire
- ISO-6934-3 - Steel for the prestressing of concrete - Part 3: Quenched and tempered wire
- ISO-6934-4 - Steel for the prestressing of concrete - Part 4: Strand
- ISO-6934-5 - Steel for the prestressing of concrete - Part 5: Hot-rolled steel bars with or without subsequent processing
- ISO-6935-1 - Steel for the reinforcement of concrete - Part 1: Plain bars
- ISO-6935-2 - Steel for the reinforcement of concrete - Part 2: Ribbed bars
- ISO-6935-3 - Steel for the reinforcement of concrete - Part 3: Welded fabric
- ISO-7728 - Typical horizontal joints between an external wall of prefabricated ordinary concrete components and a concrete floor -- Properties. characteristics and classification criteria
- ISO-7729 - Typical vertical joints between two prefabricated ordinary concrete external wall components -- Properties, characteristics and classification criteria
- ISO-7844 - Grooved vertical joints with connecting bars and concrete infill between large reinforced concrete panels -- Laboratory mechanical tests -- Effect of tangential loading
- ISO-7845 - Horizontal joints between load-bearing walls and concrete floors -- Laboratory mechanical tests -- Effect of vertical loading and of moments transmitted by the floors
Other SDOs:
- BS-EN-17678-2 - Installation of post-tensioning kits for prestressing of structures
- DIN-1045-1 - Concrete, reinforced and prestressed concrete structures - Part 1: Design and construction
- DIN-1045-2/A1 - Concrete, reinforced and prestressed concrete structures - Part 2: Concrete - Specification, properties, production and conformity; Application rules for DIN EN 206-1; Amendment A1
- DIN-1045-3 - Concrete, reinforced and prestressed concrete structures - Part 3: Execution of structures - Application rules for DIN EN 13670
- DIN-1045-3/A1 - Concrete, reinforced and prestressed concrete structures - Part 3: Execution of structures; Amendment A1
- DIN-EN-12614 - Products & Systems for the Protection & Repair of Concrete Structures - Test Methods,
- DIN-EN-12617-2 - Part 2: Shrinkage of Crack Injection Products Based on Polymer Binder: Volumetric Shri
- DIN-EN-12618-2 - Part 2: Determination of the Adhesion of Injection Products, With or Without Thermal C
- DIN-EN-12618-3 - Part 3: Determination of the Adhesion of Injection Products, With or Without Thermal C
- DIN-EN-12637-1 - Part 1: Compatibility With Concrete, Products & Systems for the Protection & Repair O
- DIN-EN-13412 - Products & Systems for the Protection & Repair of Concrete Structures - Test Methods -
- DIN-EN-14117 - Products & Systems for the Protection & Repair of Concrete Structures - Test Methods,
- DIN-EN-14406 - Products & Systems for the Protection & Repair of Concrete Structures - Test Methods,
- DIN-EN-14630 - Products & Systems for the Protection & Repair of Concrete Structures - Test Methods -
- DIN-EN-1504-1 - Part 1: Definitions, Products & Systems for the Protection & Repair of Concrete Struct
- DIN-EN-1504-10 - Part 10: Site Application of Products & Systems & Quality Control of the Works, Produc
- DIN-EN-1504-2 - Part 2: Surface Protection Systems for Concrete, Products & Systems for the Protectio
- DIN-EN-1504-3 - Part 3: Structural & Non-Structural Repair, Products & Systems for the Protection & Re
- DIN-EN-1504-4 - Part 4: Structural Bonding, Products & Systems for the Protection & Repair of Concrete
- DIN-EN-1504-5 - Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 5: Concrete injection; German version EN 1504-5:2013
- DIN-EN-1504-6 - Part 6: Anchoring of Reinforcing Steel Bar, Products & Systems for the Protection & Re
- DIN-EN-1504-7 - Part 7: Reinforcement Corrosion Protection, Products & Systems for the Protection & Re
- DIN-EN-1504-8 - Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and AVCP - Part 8: Quality control and Assessment and verification of the constancy of performance (AVCP); German version EN 1504-8:2016
- DIN-EN-15183 - Products & Systems for the Protection & Repair of Concrete Structures - Test Methods -
- DIN-EN-15184 - Products & Systems for the Proection & Repair of Concrete Structures - Test Methods -
- DIN-EN-1544 - Products & Systems for the Protection & Repair of Concrete Structures - Test Methods -
- DIN-EN-1771 - Products & Systems for the Protection & Repair of Concrete Structures - Test Methods
- DIN-EN-1881 - Products & Systems for the Protection & Repair of Concrete Structures - Test Methods -
- DIN-EN-1992-1-1 - Eurocode 2: Design of concrete structures - Part 1-1: General rules and rules for buildings; German version EN 1992-1-1:2004 + AC:2010
- DIN-EN-1992-1-2 - Part 1-2: General Rules - Structural Fire Design, Eurocode 2: Design of Concrete Struc
- DIN-EN-1992-2 - Part 2: Concrete Bridges - Design & Detailing Rules, Eurocode 2: Design of Concrete St
- DIN-EN-1992-3 - Part 3: Liquid Retaining & Containment Structures, Eurocode 2: Design of Concrete Str
- DIN-EN-1994-1-1 - Part 1-1: General Rules & Rules for Buildings, Eurocode 4: Design of Composite Steel &
- DIN-EN-1994-1-2 - Eurocode 4: Design of composite steel and concrete structures - Part 1-2: General rules - Structural fire design; German version EN 1994-1-2:2005 + AC:2008
- DIN-EN-1994-2 - Part 2: General Rules & Rules for Bridges, Eurocode 4: Design of Composite Steel & Con
- EN-12269-2 - Part 2: Long-Term Test, Determination of the Bond Behaviour Between Reinforcing Steel
- EN-12614 - Products & Systems for the Protection & Repair of Concrete Structures - Test Methods,
- EN-12617-2 - Part 2: Shrinkage of Crack Injection Products Based on Polymer Binder: Volumetric Shri
- EN-12618-2 - Part 2: Determination of the Adhesion of Injection Products, With or Without Thermal C
- EN-12618-3 - Part 3: Determination of the Adhesion of Injection Products, With or Without Thermal C
- EN-12637-1 - Part 1: Compatibility With Concrete, Products & Systems for the Protection & Repair O
- EN-13381-3 - Test methods for determining the contribution to the fire resistance of structural members - Part 3: Applied protection to concrete members
- EN-13412 - Products & Systems for the Protection & Repair of Concrete Structures - Test Methods -
- EN-13670 - Execution of concrete structures
- EN-13687-1 - Part 1: Freeze-Thaw Cycling With De-Icing Salt Immersion, Products & Systems for the P
- EN-13687-2 - Part 2: Thunder-Shower Cycling (Thermal Shock), Products & Systems for the Protection
- EN-13687-3 - Part 3: Thermal Cycling Without De-Icing Salt Impact, Products & Systems for the Prote
- EN-13687-4 - Part 4: Dry Thermal Cycling, Products & Systems for the Protection & Repair of Concret
- EN-13687-5 - Part 5: Resistance To Temperature Shock, Products & Systemsfor the Protection & Repai
- EN-13733 - Products & Systems for the Protection & Repair of Concrete Structures, Test Methods -
- EN-13791 - Assessment of In-Situ Compressive Strength in Structures & Pre-Cast Concrete Component
- EN-14038-1 - Electrochemical realkalization and chloride extraction treatments for reinforced concrete - Part 1: Realkalization
- EN-14406 - Products & Systems for the Protection & Repair of Concrete Structures - Test Methods,
- EN-14497 - Products & Systems for the Protection & Repair of Concrete Structures, Test Methods, D
- EN-14498 - Products & Systems for the Protection & Repair of Concrete Structures - Test Methods,
- EN-1504-1 - Products & Systems for the Protection & Repair of Concrete Structures, Definitions, Re
- EN-1504-10 - Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 10: Site application of products and systems and quality control of the works
- EN-1504-2 - Part 2: Surface Protection Systems for Concrete, Products & Systems for the Protectio
- EN-1504-3 - Part 3: Structural & Non-Structural Repair, Products & Systems for the Protection & Re
- EN-1504-4 - Part 4: Structural Bonding, Products & Systems for the Protection & Repair of Concrete
- EN-1504-5 - Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 5: Concrete injection
- EN-1504-6 - Part 6: Anchoring of Reinforcing Steel Bar, Products & Systems for the Protection & Re
- EN-1504-7 - Part 7: Reinforcement Corrosion Protection, Products & Systems for the Protection & Re
- EN-1504-8 - Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and AVCP - Part 8: Quality control and Assessment and verification of the constancy of performance (AVCP)
- EN-1504-9 - Products & Systems for the Protection & Repair of Concrete Structures, Definitions, Re
- EN-15183 - Products & Systems for the Protection & Repair of Concrete Structures - Test Methods -
- EN-15184 - Products & Systems for the Protection & Repair of Concrete Structures - Test Methods -
- EN-1766 - Products and systems for the protection and repair of concrete structures - Test methods - Reference concretes for testing
- EN-1771 - Products & Systems for the Protection & Repair of Concrete Structures - Test Methods
- EN-1992-1-1 - Eurocode 2: Design of concrete structures - Part 1-1: General rules and rules for buildings
- EN-1992-1-1(NA) - Uk National Annex To Eurocode 2, Design of Concrete Structures, General Rules & Rules
- EN-1992-1-2 - Part 1-2: General Rules - Structural Fire Design, Eurocode 2: Design of Concrete Struc
- EN-1992-1-2(NA) - Uk National Annex To Eurocode 2, Design of Concrete Structures, General Rules, Structu
- EN-1992-2 - Part 2: Concrete Bridges - Design & Detailing Rules, Eurocode 2: Design of Concrete St
- EN-1992-3 - Part 3: Liquid Retaining & Containment Structures, Eurocode 2: Design of Concrete Str
- EN-1992-3(NA) - Uk National Annex To Eurocode 2, Design of Concrete Structures, Liquid Retaining & Con
- EN-1992-4 - Eurocode 2 - Design of concrete structures - Part 4: Design of fastenings for use in concrete
- EN-1994-1-1 - Part 1-1: General Rules & Rules for Buildings, Eurocode 4: Design of Composite Steel &
- EN-1994-1-1(NA) - Uk National Annex To Eurocode 4, Design of Composite Steel & Concrete Structures, Gene
- EN-1994-1-2 - Eurocode 4 - Design of composite steel and concrete structures - Part 1-2: General rules - Structural fire design
- EN-1994-1-2(NA) - Uk National Annex To Eurocode 4, Design of Composite Steel & Concrete Structures, Gene
- EN-1994-2 - Part 2: General Rules & Rules for Bridges, Eurocode 4: Design of Composite Steel & Con
- EN-524-1 - Steel Strip Sheaths for Prestressing Tendons, Test Methods, Determination of Shape &
- EN-524-2 - Steel Strip Sheaths for Prestressing Tendons, Test Methods, Determination of Flexural
- EN-524-3 - Steel Strip Sheats for Prestressing Tendons, Test Methods, To-&-Fro Bending Test
- EN-524-4 - Steel Strip Sheaths for Prestressing Tendons, Test Methods, Determination of Lateral
- EN-524-5 - Steel Strip Sheaths for Prestressing Tendons, Test Methods, Determination of Tensile
- EN-524-6 - Steel Strip Sheaths for Prestressing Tendons, Test Methods, Determination of Leak Tig
- EN-ISO-15630-2 - Part 2: Welded Fabric, Steel for the Reinforcement & Prestressing of Concrete - Test M
- JIS-A-1191 - Test method for tensile properties of fiber reinforced polymer (FRP) sheets for reinforcement of concrete
- SIS-219180 - Steel fabric for concrete reinforcement. Technical conditions of delivery
- SIS-CEN-1992-4-1 - Design of fastenings for use in concrete - Part 4-1: General
- SIS-CEN-1992-4-2 - Design of fastenings for use in concrete - Part 4-2: Headed Fasteners
- SIS-CEN-1992-4-3 - Design of fastenings for use in concrete - Part 4-3: Anchor channels
- SIS-CEN-1992-4-4 - Design of fastenings for use in concrete - Part 4-4: Post-installed fasteners - Mechanical systems
- SIS-CEN-1992-4-5 - Design of fastenings for use in concrete - Part 4-5: Post-installed fasteners - Chemical systems
- SIS-CEN/TR-15177 - Testing the freeze-thaw resistance of concrete - Internal structural damage
- SIS-CEN/TR-17079 - Design of fastenings for use in concrete - Redundant non-structural systems
- SIS-CEN/TR-17080 - Design of fastenings for use in concrete - Anchor channels - Supplementary rules
- SIS-CEN/TR-17081 - Design of fastenings for use in concrete - Plastic design of fastenings with headed and post-installed fasteners
- SIS-CEN/TS-14038-1 - Electrochemical realkalization and chloride extraction treatments for reinforced concrete - Part 1: Realkalization
- SIS-CEN/TS-1992-4-1 - Design of fastenings for use in concrete - Part 4-1: General
- SIS-CEN/TS-1992-4-2 - Design of fastenings for use in concrete - Part 4-2: Headed Fasteners
- SIS-CEN/TS-1992-4-3 - Design of fastenings for use in concrete - Part 4-3: Anchor channels
- SIS-CEN/TS-1992-4-4 - Design of fastenings for use in concrete - Part 4-4: Post-installed fasteners - Mechanical systems
- SIS-CEN/TS-1992-4-5 - Design of fastenings for use in concrete - Part 4-5: Post-installed fasteners - Chemical systems
- SIS-ISO/TR-16475 - Guidelines for the repair of water-leakage cracks in concrete structures
- SS-212551 - Prestressing steels - General requirements
- SS-212552 - Prestressing steels - Wire
- SS-212553 - Prestressing steels - Strand
- SS-212554 - Prestressing steels - Bar
- SS-812310 - Fibre Concrete - Design of Fibre Concrete Structures
- SS-EN-12188 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of adhesion steel-to-steel for characterisation of structural bonding agents
- SS-EN-12189 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of open time
- SS-EN-12192-1 - Products and systems for the protection and repair of concrete structures - Granulometry analysis - Part 1: Test method for dry components of premixed mortar
- SS-EN-12192-2 - Products and systems for the protection and repair of concrete structures - Granulometry analysis - Part 2: Test method for fillers for polymer bonding agents
- SS-EN-12269-1 - Determination of the bond behaviour between reinforcing steel and autoclaved aerated concrete by the "beam test" - Part 1: Short term test
- SS-EN-12269-2 - Determination of the bond behaviour between reinforcing steel and autoclaved aerated concrete by the beam test - Part 2: Long term test
- SS-EN-12614 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of glass transition temperatures of polymers
- SS-EN-12615 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of slant shear strength
- SS-EN-12617-1 - Products and systems for the protection and repair of concrete structures - Test methods - Part 1: Determination of linear shrinkage for polymers and surface protection systems (SPS)
- SS-EN-12617-2 - Products and systems for the protection and repair of concrete structures - Test methods - Part 2: Shrinkage of crack injection products based on polymer binder: volumetric shrinkage
- SS-EN-12617-3 - Products and systems for the protection and repair of concrete structures - Test methods - Part 3: Determination of early age linear shrinkage for structural bonding agents
- SS-EN-12617-4 - Products and systems for the protection and repair of concrete structures - Test methods - Part 4: Determination of shrinkage and expansion
- SS-EN-12618-1 - Products and systems for the protection and repair of concrete structures - Test methods - Part 1: Adhesion and elongation capacity of injection products with limited ductility
- SS-EN-12618-2 - Products and systems for the protection and repair of concrete structures - Test methods - Part 2: Determination of the adhesion of injection products, with or without thermal cycling - Adhesion by tensile bond strength
- SS-EN-12618-3 - Products and systems for the protection and repair of concrete structures - Test methods - Part 3: Determination of the adhesion of injection products, with or without thermal cycling - Slant shear method
- SS-EN-12637-1 - Products and systems for the protection and repair of concrete structures - Test methods - Compatibility of injection products - Part 1: Compatibility with concrete
- SS-EN-12637-3 - Products and systems for the protection and repair of concrete structures - Test methods - Compatibility of injection products - Part 3: Effect of injection products on elastomers
- SS-EN-12696 - Cathodic protection of steel in concrete
- SS-EN-13035-3 - Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 3: Cutting machines
- SS-EN-13057 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of resistance of capillary absorption
- SS-EN-13062 - Products and systems for the protection and repair of concrete structure - Test method - Determination of thixotropy of products for protection of reinforcement
- SS-EN-13294 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of stiffening time
- SS-EN-13295 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of resistance to carbonation
- SS-EN-13381-3 - Test methods for determining the contribution to the fire resistance of structural members - Part 3: Applied protection to concrete members
- SS-EN-13391 - Mechanical tests for post-tensioning systems
- SS-EN-13395-1 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of workability - Part 1: Test for flow of thixotropic mortars
- SS-EN-13395-2 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of workability - Part 2: Test for flow of grout or mortar
- SS-EN-13395-3 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of workability - Part 3: Test for flow of repair concrete
- SS-EN-13395-4 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of workability - Part 4: Application of repair mortar overhead
- SS-EN-13396 - Products and systems for the protection and repair of concrete structures - Test methods - Measurement of chloride ion ingress
- SS-EN-13412 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of modulus of elasticity in compression
- SS-EN-13529 - Products and systems for the protection and repair of concrete structures - Test methods - Resistance to severe chemical attack
- SS-EN-13578 - Products and systems for the protection and repair of concrete structure - Test method - Compatibility on wet concrete
- SS-EN-13579 - Products and systems for the protection and repair of concrete structures - Test methods - Drying test for hydrophobic impregnation
- SS-EN-13580 - Products and systems for the protection and repair of concrete structures - Test Methods - Water absorption and resistance to alkali for hydrophobic impregnations
- SS-EN-13581 - Products and systems for the protection and repair of concrete structures - Test method - Determination of loss of mass of hydrophobic impregnated concrete after freeze-thaw salt stress
- SS-EN-13584 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of creep in compression for repair products
- SS-EN-13670 - Execution of concrete structures
- SS-EN-13687-1 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 1: Freeze-thaw cycling with de-icing salt immersion
- SS-EN-13687-2 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 2: Thunder-shower cycling (thermal shock)
- SS-EN-13687-3 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 3: Thermal cycling without de-icing salt impact
- SS-EN-13687-4 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 4: Dry thermal cycling
- SS-EN-13687-5 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of thermal compatibility - Part 5: Resistance to temperature shock
- SS-EN-13733 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of the durability of structural bonding agents
- SS-EN-13791 - Assessment of in-situ compressive strength in structures and precast concrete components
- SS-EN-13803-2 - Railway applications - Track -Track alignment design parameters - Track gauges 1 435 mm and wider - Part 2: Switches and crossings and comparable alignment design situations with abrupt changes of curvature
- SS-EN-13894-1 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of fatigue under dynamic loading - Part 1: During cure
- SS-EN-13894-2 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of fatigue under dynamic loading - Part 2: After hardening
- SS-EN-14038-1 - Electrochemical realkalization and chloride extraction treatments for reinforced concrete - Part 1: Realkalization
- SS-EN-14068 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of watertightness of injected cracks without movement in concrete
- SS-EN-14246 - Gypsum elements for suspended ceilings - Definitions, requirements and test methods
- SS-EN-14406 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of the expansion ratio and expansion evolution
- SS-EN-14497 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of the filtration stability
- SS-EN-14498 - Products and systems for the protection and repair of concrete structures - Test methods - Volume and weight changes of injection products after air drying and water storage cycles
- SS-EN-14878 - Textiles - Burning behaviour of children's nightwear - Specification
- SS-EN-14992 - Precast concrete products - Wall elements
- SS-EN-1504-1 - Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 1: Definitions
- SS-EN-1504-10 - Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 10: Site application of products and systems and quality control of the works
- SS-EN-1504-2 - Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 2: Surface protection systems for concrete
- SS-EN-1504-3 - Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 3: Structural and non-structural repair
- SS-EN-1504-4 - Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 4: Structural bonding
- SS-EN-1504-5 - Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 5: Concrete injection
- SS-EN-1504-6 - Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 6: Anchoring of reinforcing steel bar
- SS-EN-1504-7 - Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 7: Reinforcement corrosion protection
- SS-EN-1504-8 - Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and AVCP - Part 8: Quality control and Assessment and verification of the constancy of performance (AVCP)
- SS-EN-1504-9 - Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 9: General principles for the use of products and systems
- SS-EN-15091 - Sanitary tapware - Electronic opening and closing sanitary tapware
- SS-EN-15183 - Products and systems for the protection and repair of concrete structures - Test methods - Corrosion protection test
- SS-EN-15184 - Products and systems for the protection and repair of concrete structures - Test methods - Shear adhesion of coated steel to concrete (pull-out test)
- SS-EN-15238 - Soil improvers and growing media - Determination of quantity for materials with particle size greater than 60 mm
- SS-EN-1542 - Products and systems for the protection and repair of concrete structures - Test methods - Measurement of bond strength by pull-off
- SS-EN-1543 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of tensile strenght development for polymers
- SS-EN-1737 - Determination of shear strength of welded joints of reinforced mats or cages for prefabricated components made of autoclaved aerated concrete or lightweight aggregate concrete with open structure
- SS-EN-1738 - Determination of steel stresses in unloaded reinforced components made of autoclaved aerated concrete
- SS-EN-1739 - Determination of shear strength for in-plane forces of joints between prefabricated components of autoclaved aerated concrete or lightweight aggregate concrete with open structure
- SS-EN-1740 - Performance test for prefabricated reinforced components made of autoclaved concrete or ligtweight aggregate concrete with open structure under predominantly longitudinal load (vertical components)
- SS-EN-1741 - Determination of shear strength for out-of-plane forces of joints between prefabricated components made of autoclaved aerated concrete or lightweightaggregate concrete with open structure
- SS-EN-1742 - Determination of shear strength between differentlayers of multilayer components made of autoclaved aerated concrete or lightweight aggregate concrete with open structure
- SS-EN-1766 - Products and systems for the protection and repair of concrete structures - Test methods - Reference concretes for testing
- SS-EN-1767 - Products and systems for protection and repair of concrete structures - Test methods - Infrared analysis
- SS-EN-17678-1 - Installation of post-tensioning kits for prestressing of structures - Part 1: Competence of personnel
- SS-EN-17678-2 - Installation of post-tensioning kits for prestressing of structures - Part 2: Assessment of personnel
- SS-EN-1770 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of the coefficient of thermal expansion
- SS-EN-1771 - Products and systems for the protection and repair of concrete structures - Test methods - Determination of injectability using the sand column test
- SS-EN-1799 - Products and systems for the protection and repair of concrete structures - Test methods - Tests to measure the suitability of structural bonding agents for application to concrete surface
- SS-EN-1877-1 - Products and systems for the protection and repair of concrete structures - Test methods - Reactive functions related to epoxy resins - Part 1: Determination of epoxy equivalent
- SS-EN-1877-2 - Products and systems for the protection and repair of concrete structures - Test methods - Reactive functions related to epoxy resins - Part 2: Determination of amine functions using the total basicity number
- SS-EN-1991-1-7 - Eurocode 1 - Actions on structures - Part 1-7: General actions - Accidental actions
- SS-EN-1992-1-1 - Eurocode 2 - Design of concrete structures - Part 1-1: General rules and rules for buildings, bridges and civil engineering structures
- SS-EN-1992-1-1-AM1 - Eurocode 2: Design of concrete structures - Part 1-1: General rules and rules for buildings
- SS-EN-1992-1-2 - Eurocode 2 - Design of concrete structures Part 1-2: Structural fire design
- SS-EN-1992-1-2-AM1 - Eurocode 2: Design of concrete structures - Part 1-2: General rules - Structural fire design
- SS-EN-1992-2 - Eurocode 2: Design of concrete structures - Part 2: Concrete bridges - Design and detailing rules
- SS-EN-1992-3 - Eurocode 2: Design of concrete structures - Part 3: Liquid retaining and containment structures
- SS-EN-1992-4 - Eurocode 2 - Design of concrete structures - Part 4: Design of fastenings for use in concrete
- SS-EN-1994-1-1 - Eurocode 4: Design of composite steel and concrete structures - Part 1-1: General rules and rules for buildings
- SS-EN-1994-1-2 - Eurocode 4: Design of composite steel and concrete structures - Part 1-2: General rules - Structural fire design
- SS-EN-1994-1-2-AM1 - Eurocode 4 - Design of composite steel and concrete structures - Part 1-2: General rules - Structural fire design
- SS-EN-1994-2 - Eurocode 4 - Design of composite steel and concrete structures - Part 2: General rules and rules for bridges
- SS-EN-523 - Steel strip sheaths for prestressing tendons - Terminology, requirements, quality control
- SS-EN-524-1 - Steel strip sheaths for prestressing tendons - Test methods - Part 1: Determination of shape and dimensions
- SS-EN-524-2 - Steel strip sheaths for prestressing tendons - Test methods - Part 2: Determination of flexural behaviour
- SS-EN-524-3 - Steel strip sheaths for prestressing tendons - Test methods - Part 3: To-and-fro bending test
- SS-EN-524-4 - Steel strip sheaths for prestressing tendons - Test methods - Part 4: Determination of lateral loadresistance
- SS-EN-524-5 - Steel strip sheaths for prestressing tendons - Test methods - Part 5: Determination of tensile loadresistance
- SS-EN-524-6 - Steel strip sheaths for prestressing tendons - Test methods - Part 6: Determination of leaktightness (Determination of water loss)
- SS-EN-861 - Safety of woodworking machines - Surface planing and thicknessing machines
- SS-EN-989 - Determination of the bond behavior between reinforcing bars and autoclaved aerated concrete by the "Push-Out" test
- SS-EN-990 - Test methods for verification of corrosion protection of reinforcement in autoclaved aerated concrete and lightweight aggregate concrete with open structure
- SS-EN-991 - Determination of the dimensions of prefabricated reinforced components made of autoclaved aerated concrete or lightweight aggregate concrete with open structure
- SS-EN-992 - Determination of the dry density of lightweight concrete with open structure
- SS-EN-ISO-12696 - Cathodic protection of steel in concrete (ISO 12696:2022)
- SS-EN-ISO-15630-1 - Steel for the reinforcement and prestressing of concrete - Test methods - Part 1: Reinforcing bars, rods and wire (ISO 15630-1:2019)
- SS-EN-ISO-15630-2 - Steel for the reinforcement and prestressing of concrete - Test methods - Part 2: Welded fabric and lattice girders (ISO 15630-2:2019)
- SS-EN-ISO-15630-3 - Steel for the reinforcement and prestressing of concrete - Test methods - Part 3: Prestressing steel (ISO 15630-3:2019)
- SS-ENV-10080 - Steel for the reinforcement of concrete - Weldable ribbed reinforcing steel B500 - Technical delivery conditions for bars, coils and welded fabric
- SS-ENV-1504-9 - Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 9: General principles for the use of products and systems
- SS-ENV-1992-1-2 - Eurocode 2: Design of concrete structures - Part 1-2: General rules - Structural fire design
- SS-ENV-206 - Concrete - Performance, production, placing and compliance criteria
- SS-ISO-10065 - Steel bars for the reinforcement of concrete - Bend and rebend test
- SS-ISO-10606 - Steel for the reinforcement of concrete - Determination of percentage total elongation at maximum force
- SS-ISO-14484 - Performance guidelines for design of concrete structures using fibre-reinforced polymer (FRP) materials (ISO 14484:2013, IDT)
- SS-ISO-16204 - Durability - Service life design of concrete structures (ISO 16204:2012, IDT)
- SS-ISO-18319 - Fibre-reinforced polymer (FRP) reinforcement for concrete structures - Specifications of FRP sheets (ISO 18319:2015, IDT)
- SS-ISO-48 - Rubber, vulcanized or thermoplastic - Determination of hardness (hardness between 10 IRHD och 100 IRHD) (ISO 48:2010, IDT)
- SS-ISO-5006 - Earth-moving machinery - Operator's field of view - Test method and performance criteria (ISO 5006:2017, IDT)
- UNE-EN-1992-1-1 - Eurocode 2: Design of concrete structures - Part 1-1: General rules and rules for buildings
- UNE-EN-1992-1-1/A1 - Eurocode 2: Design of concrete structures - Part 1-1: General rules and rules for buildings
- UNE-EN-1994-1-2 - Eurocode 4 - Design of composite steel and concrete structures - Part 1-2: General rules - Structural fire design.