Document Center List of Standards on Construction Materials In General
ICS Code 91.100.01
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
ASTM:
- ASTM-C1067 - Standard Practice for Conducting a Ruggedness Evaluation or Screening Program for Test Methods for Construction Materials
- ASTM-C142 - Standard Test Method for Clay Lumps and Friable Particles in Aggregates
- ASTM-C1587 - Standard Practice for Preparation of Field Removed Manufactured Masonry Units and Masonry Specimens for Testing
- ASTM-C1670 - Standard Specification for Adhered Manufactured Stone Masonry Veneer Units
- ASTM-C1794 - Standard Test Methods for Determination of the Water Absorption Coefficient by Partial Immersion
- ASTM-C566 - Standard Test Method for Total Evaporable Moisture Content of Aggregate by Drying
- ASTM-C670 - Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials
- ASTM-C802 - Standard Practice for Conducting an Interlaboratory Test Program to Determine the Precision of Test Methods for Construction Materials
- ASTM-C904 - Standard Terminology Relating to Chemical-Resistant Nonmetallic Materials
- ASTM-D3665 - Standard Practice for Random Sampling of Construction Materials
- ASTM-D5282 - Standard Test Methods for Compatibility of Construction Material with Silicone Fluid Used for Electrical Insulation
- ASTM-D6024 - Standard Test Method for Ball Drop on Controlled Low Strength Material (CLSM) to Determine Suitability for Load Application
- ASTM-D7886 - Standard Practice for Asbestos Exposure Assessments for Repetitive Maintenance and Installation Tasks
- ASTM-E105 - Standard Practice for Probability Sampling of Materials
- ASTM-E119 - Standard Test Methods for Fire Tests of Building Construction and Materials
- ASTM-E1321 - Standard Test Method for Determining Material Ignition and Flame Spread Properties
- ASTM-E136 - Standard Test Method for Assessing Combustibility of Materials Using a Vertical Tube Furnace at 750°C
- ASTM-E1623 - Standard Test Method for Determination of Fire and Thermal Parameters of Materials, Products, and Systems Using an Intermediate Scale Calorimeter (ICAL)
- ASTM-E1861 - Standard Guide for Use of Coal Combustion By-Products in Structural Fills (Withdrawn 2003)
- ASTM-E1991 - Standard Guide for Environmental Life Cycle Assessment (LCA) of Building Materials/Products (Withdrawn 2014)
- ASTM-E2178 - Standard Test Method for Determining Air Leakage Rate and Calculation of Air Permeance of Building Materials
- ASTM-E2768 - Standard Test Method for Extended Duration Surface Burning Characteristics of Building Materials (30 min Tunnel Test)
- ASTM-E3075 - Standard Test Method for Water Immersion and Drying for Evaluation of Flood Damage Resistance
- ASTM-E329 - Standard Specification for Agencies Engaged in Construction Inspection, Testing, or Special Inspection
- ASTM-E632 - Standard Practice for Developing Accelerated Tests to Aid Prediction of the Service Life of Building Components and Materials (Withdrawn 2005)
- ASTM-E84 - Standard Test Method for Surface Burning Characteristics of Building Materials
- ASTM-G162 - Standard Practice for Conducting and Evaluating Laboratory Corrosion Tests in Soils
- ASTM-PS23 - Guide for the Use of Coal Combustion Fly Ash in Structural Fills (Withdrawn 1997)
- ASTM-PS30 - Practice for Sampling Freshly Mixed Controlled Low Strength Material (Withdrawn 1996)
BSI:
- BS-1924 - Methods of test for stabilized soils
- BS-1924-1 - Hydraulically bound and stabilized materials for civil engineering purposes
- BS-1924-1-TC - Tracked Changes. Hydraulically bound and stabilized materials for civil engineering purposes
- BS-1924-2 - Hydraulically bound and stabilized materials for civil engineering purposes
- BS-1924-2-TC - Tracked Changes. Hydraulically bound and stabilized materials for civil engineering purposes
- BS-4940 - Recommendations for the presentation of technical information about products and services in the construction industry
- BS-4940-2 - Technical information on construction products and services
- BS-4940-3 - Technical information on construction products and services. Guide to presentation
- BS-648 - Schedule of weights of building materials
- BS-6543 - Guide to use of industrial by-products and waste materials in building and civil engineering
- BS-9227 - Hydraulically bound materials for civil engineering purposes. Specification for production and installation in pavements
- BS-EN-12524 - Building materials and products. Hygrothermal properties. Tabulated design values
- BS-EN-12664 - Thermal performance of building materials and products. Determination of thermal resistance by means of guarded hot plate and heat flow meter methods. Dry and moist products of medium and low thermal resistance
- BS-EN-12667 - Thermal performance of building materials and products. Determination of thermal resistance by means of guarded hot plate and heat flow meter methods. Products of high and medium thermal resistance
- BS-EN-13009 - Hygrothermal performance of building materials and products. Determination of hygric expansion coefficient
- BS-EN-13238 - Reaction to fire tests for building products. Conditioning procedures and general rules for selection of substrates
- BS-EN-13823 - Reaction to fire tests for building products. Building products excluding floorings exposed to the thermal attack by a single burning item
- BS-EN-16516 - Construction products: Assessment of release of dangerous substances. Determination of emissions into indoor air
- BS-EN-16687 - Construction products. Assessment of release of dangerous substances. Terminology
- BS-EN-17087 - Construction products: Assessment of release of dangerous substances - Preparation of test portions from the laboratory sample for testing of release and analysis of content
- BS-EN-17637 - Construction products: Assessment of release of dangerous substances. Dose assessment of emitted gamma radiation
- BS-EN-1946-4 - Measurements by hot box methods
- BS-EN-1946-5 - Thermal performance of building products and components. Specific criteria for the assessment of laboratories measuring heat transfer properties
- BS-EN-ISO-12570 - Hygrothermal performance of building materials and products. Determination of moisture content by drying at elevated temperature
- BS-EN-ISO-12571 - Hygrothermal performance of building materials and products - Determination of hygroscopic sorption properties
- BS-EN-ISO-12571-TC - Tracked Changes. Hygrothermal performance of building materials and products. Determination of hygroscopic sorption properties
- BS-EN-ISO-12572 - Hygrothermal performance of building materials and products. Determination of water vapour transmission properties. Cup method
- BS-EN-ISO-12572-TC - Tracked Changes. Hygrothermal performance of building materials and products. Determination of water vapour transmission properties. Cup method
- BS-EN-ISO-15148 - Hygrothermal performance of building materials and products. Determination of water absorption coefficient by partial immersion
- BS-EN-ISO-1716 - Reaction to fire tests for products. Determination of the gross heat of combustion (calorific value)
- BS-EN-ISO-1716-TC - Tracked Changes. Reaction to fire tests for products. Determination of the gross heat of combustion (calorific value)
- BS-ISO-23327 - Hygrothermal performance of building materials and products. Determination of moisture adsorption/desorption properties in response to periodic temperature variation
- BS-ISO-24353 - Hygrothermal performance of building materials and products. Determination of moisture adsorption/desorption properties in response to humidity variation
- BS-ISO/TR-14697 - Fire Tests, Guidance on the Choice of Substrates for Building Products
- PD-6695-2 - Recommendations for the design of bridges to BS EN 1993
- PD-CEN-14613 - Thermal performance of building materials and components. Principles for the determination of thermal properties of moist materials andcomponent s
- PD-CEN-15855 - Construction products. Assessment of release of dangerous substances. Barriers to trade
- PD-CEN-15858 - Construction products. Assessment of the release of regulated dangerous substances from construction products based on the WT, WFT/FT procedures
- PD-CEN-15985 - Thermal insulating products. Factory made products of expanded polystyrene (EPS). Voluntary certification of the raw material
- PD-CEN-16045 - Construction products. Assessment of release of dangerous substances. Content of regulated dangerous substances. Selection of analytical methods
- PD-CEN-16098 - Construction products. Assessment of release of dangerous substances. Concept of horizontal testing procedures in support of requirements under the CPD
- PD-CEN-16435 - Liquid petroleum products. Oxygenates blending in line with actual EN 228 requirements
- PD-CEN-16496 - Construction Products. Assessment of release of dangerous substances. Use of harmonised horizontal assessment methods
- PD-CEN-16516 - Construction products. Assessment of release of dangerous substances. Determination of emissions into indoor air
- PD-CEN-16637-1 - Construction products. Assessment of release of dangerous substances
- PD-CEN-16637-1-TC - Tracked Changes. Construction products. Assessment of release of dangerous substances
- PD-CEN-16637-2 - Construction products. Assessment of release of dangerous substances
- PD-CEN-16637-3 - Construction products. Assessment of release of dangerous substances
- PD-CEN-16797-1 - Construction products: Assessment of release of dangerous substances. Guidance on the statistical assessment of declared values
- PD-CEN-16797-2 - Construction products: Assessment of release of dangerous substances. Guidance on the statistical assessment of declared values
- PD-CEN-17105 - Construction products. Assessment of release of dangerous substances. Guidance on the use of ecotoxicity tests applied to construction products
- PD-CEN-17113 - Construction products. Assessment of release of dangerous substances. Radiation from construction products. Dose assessment of emitted gamma radiation
- PD-CEN-17195 - Construction products: Assessment of release of dangerous substances. Analysis of inorganic substances in eluates
- PD-CEN-17196 - Construction products: Assessment of release of dangerous substances. Digestion by aqua regia for subsequent analysis of inorganic substances
- PD-CEN-17197 - Construction products. Assessment of release of dangerous substances. Analysis of inorganic substances in digests and eluates. Analysis by Inductively Coupled Plasma. Optical Emission Spectrometry (ICP-OES)
- PD-CEN-17200 - Construction products. Assessment of release of dangerous substances. Analysis of inorganic substances in digests and eluates. Analysis by Inductively Coupled Plasma. Mass Spectrometry (ICP-MS)
- PD-CEN-17201 - Construction products. Assessment of release of dangerous substances. Content of inorganic substances. Methods for analysis of aqua regia digests
- PD-CEN-17216 - Construction products. Assessment of release of dangerous substances. Determination of activity concentrations of radium-226, thorium-232 and potassium-40 in construction products using semiconductor gamma-ray spectrometry
- PD-CEN-17331 - Construction products: Assessment of release of dangerous substances. Content of organic substances. Methods for extraction and analysis
- PD-CEN-17332 - Construction products: Assessment of release of dangerous substances. Analysis of organic substances in eluates
- TH-42097 - Construction Products. a Guide To the Requirements of the European Directive and To Ce Marking
ISO:
- ISO-12570 - Hygrothermal performance of building materials and products - Determination of moisture content by drying at elevated temperature
- ISO-12570-AM1 - - Amendment 1
- ISO-12570-AM2 - - Amendment 2
- ISO-12571 - Hygrothermal performance of building materials and products - Determination of hygroscopic sorption properties
- ISO-15148 - Hygrothermal performance of building materials and products - Determination of water absorption coefficient by partial immersion
- ISO-15148-AM1 - - Amendment 1
- ISO-1716 - Reaction to fire tests for products - Determination of the gross heat of combustion (calorific value)
- ISO-23327 - Hygrothermal performance of building materials and products - Determination of moisture adsorption/desorption properties in response to periodic temperature variation
- ISO-24353 - Hygrothermal performance of building materials and products - Determination of moisture adsorption/desorption properties in response to humidity variation
- ISO-24353-AM1 - - Amendment 1
Other SDOs:
- CEN-16637-1 - Construction products - Assessment of release of dangerous substances - Part 1: Guidance for the determination of leaching tests and additional testing steps
- CEN-17195 - Construction products: Assessment of release of dangerous substances - Analysis of inorganic substances in eluates
- CEN-17196 - Construction products: Assessment of release of dangerous substances - Digestion by aqua regia for subsequent analysis of inorganic substances
- CEN-17197 - Construction products: Assessment of release of dangerous substances - Analysis of inorganic substances in digests and eluates - Analysis by Inductively Coupled Plasma - Optical Emission Spectrometry (ICP-OES)
- CEN-17200 - Construction products: Assessment of release of dangerous substances - Analysis of inorganic substances in digests and eluates - Analysis by Inductively Coupled Plasma - Mass Spectrometry (ICP-MS)
- CEN-17201 - Construction products: Assessment of release of dangerous substances - Analysis of inorganic substances in digests and eluates - Analysis by Inductively Coupled Plasma - Mass Spectrometry (ICP-MS)
- CEN-17216 - Construction products - Assessment of release of dangerous substances - Determination of activity concentrations of radium-226, thorium-232 and potassium-40 in construction products using semiconductor gamma-ray spectrometry
- DIN-EN-13238 - Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates; German version EN 13238:2010
- DIN-EN-13823 - Reaction to fire tests for building products - Building products excluding floorings exposed to the thermal attack by a single burning item; German version EN 13823:2010+A1:2014
- DIN-EN-ISO-1182 - Reaction To Fire Tests for Products - Non-Combustibility Test
- DIN-EN-ISO-11925-2 - Part 2: Single-Flame Source Test, Reaction To Fire Tests - Ignitability of Products Su
- DIN-EN-ISO-12572 - Hygrothermal performance of building materials and products - Determination of water vapour transmission properties - Cup method
- DIN-EN-ISO-15148 - Hygrothermal performance of building materials and products - Determination of water absorption coefficient by partial immersion
- DIN-EN-ISO-1716 - Reaction To Fire Tests for Products - Determination of the Gross Heat of Combustion (C
- EN-13238 - Reaction To Fire Tests for Building Products - Conditioning Procedures & General Rule
- EN-13823 - Reaction to fire tests for building products - Building products excluding floorings exposed to the thermal attack by a single burning item
- EN-16516 - Construction products: Assessment of release of dangerous substances - Determination of emissions into indoor air
- EN-16687 - Construction products - Assessment of release of dangerous substances - Terminology
- EN-17087 - Construction products: Assessment of release of dangerous substances - Preparation of test portions from the laboratory sample for testing of release and analysis of content
- EN-ISO-12570 - Hygrothermal performance of building materials and products - Determination of moisture content by drying at elevated temperature - Amendment 1 (ISO 12570:2000/Amd 1:2013)
- EN-ISO-12571 - Hygrothermal performance of building materials and products - Determination of hygroscopic sorption properties (ISO 12571:2013)
- EN-ISO-1716 - Reaction To Fire Tests for Products - Determination of the Gross Heat of Combustion (C
- JIS-A-1145 - Method of test for alkali-silica reactivity of aggregates by chemical method
- JIS-A-1408 - Test methods of bending and impact for building boards
- JIS-A-1470-1 - Determination of water vapour adsorption/desorption properties for building materials -- Part 1: Response to humidity variation
- JIS-A-1470-2 - Determination of water vapour adsorption/desorption properties for building materials -- Part 2 : Response to temperature variation
- JIS-A-1475 - Method of test for hygroscopic sorption properties of building materials
- JIS-G-3140 - Higher yield strength steel plates for bridges
- SIS-CEN-17196 - Construction products: Assessment of release of dangerous substances - Digestion by aqua regia for subsequent analysis of inorganic substances
- SIS-CEN-17216 - Construction products - Assessment of release of dangerous substances - Determination of activity concentrations of radium-226, thorium-232 and potassium-40 in construction products using semiconductor gamma-ray spectrometry
- SIS-CEN/TR-15855 - Construction products - Assessment of release of dangerous substances - Barriers to trade
- SIS-CEN/TR-15858 - Construction products - Assessment of the release of regulated dangerous substances from construction products based on the WT, WFT/FT procedures
- SIS-CEN/TR-16045 - Construction products - Assessment of release of dangerous substances - Content of regulated dangerous substances - Selection of analytical methods
- SIS-CEN/TR-16098 - Construction products - Assessment of release of dangerous substances - Concept of horizontal testing procedures in support of requirements under the CPD
- SIS-CEN/TR-16220 - Construction products - Assessment of release of dangerous substances - Complement to sampling
- SIS-CEN/TR-16797-1 - Construction products: Assessment of release of dangerous substances - Guidance on the statistical assessment of declared values - Part 1: Principles and rules of application
- SIS-CEN/TR-16797-2 - Construction products: Assessment of release of dangerous substances - Guidance on the statistical assessment of declared values - Part 2: Technical and statistical background
- SIS-CEN/TR-17105 - Construction products - Assessment of release of dangerous substances - Guidance on the use of ecotoxicity tests applied to construction products
- SIS-CEN/TS-16516 - Construction products - Assessment of release of dangerous substances - Determination of emissions into indoor air
- SIS-CEN/TS-16637-1 - Construction products - Assessment of release of dangerous substances - Part 1: Guidance for the determination of leaching tests and additional testing steps
- SIS-CEN/TS-16637-2 - Construction products - Assessment of release of dangerous substances - Part 2: Horizontal dynamic surface leaching test
- SIS-CEN/TS-16637-3 - Construction products - Assessment of release of dangerous substances - Part 3: Horizontal up-flow percolation test
- SIS-CEN/TS-17331 - Construction products: Assessment of release of dangerous substances - Content of organic substances - Methods for extraction and analysis
- SIS-CEN/TS-17332 - Construction products: Assessment of release of dangerous substances - Analysis of organic substances in eluates
- SIS-TS-41 - Building materials Laboratory method for assessment of the lowest hygrothermal conditions required for mould growth
- SS-EN-12524 - Building materials and products - Hygrothermal properties - Tabulated design values
- SS-EN-12664 - Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Dry and moist products of medium and low thermal resistance
- SS-EN-12667 - Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Products of high and medium thermal resistance
- SS-EN-13009 - Hygrothermal performance of building materials and products - Determination of hygric expansion coefficient
- SS-EN-13238 - Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates
- SS-EN-13823 - Reaction to fire tests for building products - Building products excluding floorings exposed to the thermal attack by a single burning item
- SS-EN-16516 - Construction products: Assessment of release of dangerous substances - Determination of emissions into indoor air
- SS-EN-16516-AM1 - Construction products: Assessment of release of dangerous substances - Determination of emissions into indoor air
- SS-EN-16687 - Construction products - Assessment of release of dangerous substances - Terminology
- SS-EN-17087 - Construction products: Assessment of release of dangerous substances - Preparation of test portions from the laboratory sample for testing of release and analysis of content
- SS-EN-17637 - Construction products: Assessment of release of dangerous substances - Dose assessment of emitted gamma radiation
- SS-EN-1946-1 - Thermal performance of building and components - Specific criteria for the assessment of laboratories measuring heat transfer properties - Part 1: Common criteria
- SS-EN-1946-2 - Thermal performance of building products and components - Specific criteria for the assessment of laboratories measuring heat transfer properties - Part 2: Measurements by guarded hot plate method
- SS-EN-1946-3 - Thermal performance of building products and components - Specific criteria for the assessment of laboratories measuring heat transfer properties - Part 3: Measurements by heat flow meter method
- SS-EN-1946-4 - Thermal performance of building products and components - Specific criteria for the assessment of laboratories measuring heat transfer properties - Part 4: Measurements by hot box methods
- SS-EN-1946-5 - Thermal performance of building products and components - Specific criteria for the assessment of laboratories measuring heat transfer properties - Part 5: Measurements by pipe test methods
- SS-EN-ISO-10426-1 - Petroleum and natural gas industries - Cements and materials for well cementing - Part 1: Specification (ISO 10426-1:2009)
- SS-EN-ISO-10426-1-AM1 - Petroleum and natural gas industries - Cements and materials for well cementing - Part 1: Specification (ISO 10426-1:2000/Amd 1:2002)
- SS-EN-ISO-10456 - Building materials and products - Hygrothermal properties -Tabulated design values and procedures for determining declared and design thermal values (ISO 10456:2007)
- SS-EN-ISO-1182 - Reaction to fire tests for products - Non-combustibility test (ISO/DIS 1182:2019)
- SS-EN-ISO-12570 - Hygrothermal performance of building materials and products - Determination of moisture content by drying at elevated temperature (ISO 12570:2000)
- SS-EN-ISO-12570-AM1 - Hygrothermal performance of building materials and products - Determination of moisture content by drying at elevated temperature - Amendment 1 (ISO 12570:2000/Amd 1:2013)
- SS-EN-ISO-12570-AM2 - Hygrothermal performance of building materials and products - Determination of moisture content by drying at elevated temperature (ISO 12570:2000/Amd 2:2018)
- SS-EN-ISO-12571 - Hygrothermal performance of building materials and products - Determination of hygroscopic sorption properties (ISO 12571:2021)
- SS-EN-ISO-15148 - Hygrothermal performance of building materials and products - Determination of water absorption coefficient by partial immersion (ISO 15148:2002)
- SS-EN-ISO-15148-AM1 - Hygrothermal performance of building materials and products - Determination of water absorption coefficient by partial immersion - Amendment 1 (ISO 15148:2002/Amd 1:2016)
- SS-EN-ISO-1716 - Reaction to fire tests for products - Determination of the gross heat of combustion (calorific value) (ISO 1716:2018)
- SS-EN-ISO-9346 - Hygrothermal performance of buildings and building materials - Physical quantities for mass transfer - Vocabulary (ISO 9346:2007)
- SS-ISO-17572-3 - Intelligent transport systems (ITS) - Location referencing for geographic databases - Part 3: Dynamic location references (dynamic profile) (ISO 17572-3:2008, IDT)
- UNE-EN-ISO-15148 - Hygrothermal performance of building materials and products - Determination of water absorption coefficient by partial immersion
- UNE-EN-ISO-15148/A1 - Hygrothermal performance of building materials and products - Determination of water absorption coefficient by partial immersion - Amendment 1