Document Center List of Standards on Water Supply Systems Including Water Meters In Buildings External Water Conveyance Systems, See 93.025
ICS Code 91.140.60
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
ASTM:
- ASTM-C1802 - Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures
- ASTM-E2984 - Standard Practice for Acoustic Emission Examination of High Pressure, Low Carbon, Forged Piping using Controlled Hydrostatic Pressurization
- ASTM-F2769 - Standard Specification for Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems
- ASTM-F3182 - Standard Practice for the Application of Spray-Applied Polymeric Liners Inside Pipelines for Potable Water
BSI:
- BIP-2177 - Hot and Cold Water Supply. 3rd edition
- BS-1010-2 - Specification for draw-off taps and stopvalves for water services (screw-down pattern). Draw-off taps and above-ground stopvalves
- BS-1212-1 - Float operated valves
- BS-1212-2 - Float operated valves
- BS-1212-3 - Float operated valves
- BS-1212-4 - Float operated valves
- BS-1212-4-TC - Tracked Changes. Float operated valves
- BS-1566-1 - Copper indirect cylinders for domestic purposes
- BS-1566-2 - Copper indirect cylinders for domestic purposes
- BS-1968 - Specification for floats for ballvalves (copper)
- BS-2456 - Specification for floats (plastics) for float operated valves for cold water services
- BS-2580 - Specification for underground plug cocks for cold water services
- BS-2879 - Specification for draining taps (screw-down pattern)
- BS-3198 - Specification for copper hot water storage combination units for domestic purposes
- BS-3284 - Specification for Polythene Pipe (Type 50) for Cold Water Services
- BS-3505 - Specification for unplasticized polyvinyl chloride (PVC-U) pressure pipes for cold potable water
- BS-417-2 - Specification for galvanized low carbon steel cisterns, cistern lids, tanks and cylinders
- BS-4213 - Cisterns for domestic use. Cold water storage and combined feed and expansion (thermoplastic) cisterns up to 500 l. Specification
- BS-4346-1 - Joints and fittings for use with unplasticized PVC pressure pipes. Injection moulded unplasticized PVC fittings for solvent welding for use with pressure pipes, including potable water supply
- BS-534 - Steel Pipes, Joints & Specials for Water & Sewage, Specification For
- BS-5388 - Specification for spray taps
- BS-5412-1 - Specification for the performance of draw-off taps with metal bodies for water services. Dimensional and design characteristics
- BS-5412-2 - Specification for the performance of draw-off taps with metal bodies for water services. Water tightness and pressure resistance characteristics
- BS-5412-3 - Specification for the performance of draw-off taps with metal bodies for water services. Hydraulic characteristics
- BS-5412-4 - Specification for the performance of draw-off taps with metal bodies for water services. Mechanical and endurance characteristics
- BS-5412-5 - Specification for the performance of draw-off taps with metal bodies for water services. Physio-chemical characteristics: materials, coatings
- BS-5433 - Specification for underground stopvalves for water services
- BS-5480 - Specification for glass reinforced plastics (GRP) pipes, joints and fittings for use for water supply or sewerage
- BS-5615 - Specification for insulating jackets for domestic hot water storage cylinders
- BS-5779 - Specification for spray mixing taps
- BS-5834-1 - Surface boxes, guards and underground chambers for the purposes of utilities
- BS-5834-1-TC - Tracked Changes. Surface boxes, guards and underground chambers for the purposes of utilities
- BS-5834-2 - Surface boxes, guards and underground chambers for the purposes of utilities
- BS-5834-4 - Surface boxes, guards and underground chambers for the purposes of utilities
- BS-5955-8 - Plastics pipework (thermoplastics materials)
- BS-6144 - Specification for expansion vessels using an internal diaphragm, for unvented hot water supply systems
- BS-6282-3 - Specification for In-Line Anti-Vacuum Valves of Nominal Sizeup To and Including DN 42F
- BS-6283-2 - Safety and control devices for use in hot water systems
- BS-6283-4 - Specification for Drop-Tight Pressure Reducing Valves of Nominal Size Up To and Includ
- BS-6572 - Blue Polyethylene Pipes Up To Nominal Size 63 for Below Ground Use for Potable Water, Brit
- BS-6675 - Specification for servicing valves (copper alloy) for water services
- BS-6700 - Design, installation, testing and maintenance of services supplying water for domestic use within buildings and their curtilages Specification
- BS-6759-1 - Safety valves. Specification for safety valves for steam and hot water
- BS-7181 - Specification for storage cisterns up to 500 L actual capacity for water supply for domestic purposes
- BS-7206 - Specification for Unvented Hot Water Storage Units and Packages
- BS-7291-1 - Thermoplastics pipe and tting systems for hot and cold water for domestic purposes and heating installations in buildings
- BS-7291-2 - Thermoplastics pipe and ?tting systems for hot and cold water for domestic purposes and heating installations in buildings
- BS-7291-3 - Thermoplastics pipe and ?tting systems for hot and cold water for domestic purposes and heating installations in buildings
- BS-7291-4 - Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings. Specification for chlorinated polyvinyl chloride (PVC-C) pipes and associated fittings and solvent cement
- BS-7350 - Specification for double regulating globe valves and flow measurement devices for heating and chilled water systems
- BS-853-1 - Specification for vessels for use in heating systems
- BS-8554 - Code of practice for the sampling and monitoring of hot and cold water services in buildings
- BS-8558 - Guide to the design, installation, testing and maintenance of services supplying water for domestic use within buildings and their curtilages. Complementary guidance to BS EN 806
- BS-8614 - Water meters. Additional requirements for meters with polymer main casings
- BS-8680 - Water quality. Water safety plans. Code of practice
- BS-8680 EXPERT COMM - Expert Commentary for BS 8680:2020. Water quality. Water safety plans. Code of practice
- BS-879 - Specification for water well casing
- BS-879-1 - Water well casing. Specification for steel tubes for casing
- BS-879-2 - Water well casing
- BS-EN-10312 - Welded stainless steel tubes for the conveyance of aqueous liquids inclu ding water for human consumption. Technical delivery conditions
- BS-EN-1074-1 - Valves for water supply. Fitness for purpose requirements and appropriate verification tests
- BS-EN-1074-2 - Valves for water supply. Fitness for purpose requirements and appropriate verification tests
- BS-EN-1074-3 - Valves for water supply. Fitness for purpose requirements and appropriate verification tests
- BS-EN-1074-4 - Valves for water supply. Fitness for purpose requirements and appropriate verification tests
- BS-EN-1213 - Building valves. Copper alloy stopvalves for potable water supply in buildings. Tests and requirements
- BS-EN-12201-1 - Plastics piping systems for water supply, and for drains and sewers under pressure. Polyethylene (PE)
- BS-EN-12201-2 - Plastics piping systems for water supply, and for drains and sewers under pressure. Polyethylene (PE)
- BS-EN-12201-3 - Plastics piping systems for water supply, and for drains and sewers under pressure. Polyethylene (PE)
- BS-EN-12201-4 - Plastics piping systems for water supply, and for drains and sewers under pressure. Polyethylene (PE)
- BS-EN-12201-5 - Plastics piping systems for water supply, and for drains and sewers under pressure. Polyethylene (PE)
- BS-EN-12201-5-TC - Tracked Changes. Plastics piping systems for water supply, and for drains and sewers under pressure. Polyethylene (PE)
- BS-EN-12502-3 - Protection of metallic materials against corrosion. Guidance on the assessment of corrosion likelihood in water distribution and storage systems
- BS-EN-12502-4 - Protection of metallic materials against corrosion. Guidance on the assessment of corrosion likelihood in water distribution and storage systems
- BS-EN-12729 - Devices to prevent pollution by backflow of potable water. Controllable backflow preventer with reduced pressure zone. Family B. Type A
- BS-EN-13076 - Devices to prevent pollution by backflow of potable water. Unrestricted air gap. Family A. Type A
- BS-EN-13077 - Devices to prevent pollution by backflow of potable water. Air gap with non-circular overflow (unrestricted). Family A. Type B
- BS-EN-13079 - Devices to prevent pollution by backflow of potable water. Air gap with injector. Family A. Type D
- BS-EN-13443-1 - Water conditioning equipment inside buildings. Mechanical filters
- BS-EN-13443-2 - Water conditioning equipment inside buildings. Mechanical filters
- BS-EN-13618 - Flexible hose assemblies in drinking water installations. Functional requirements and test methods
- BS-EN-13618-TC - Tracked Changes. Flexible hose assemblies in drinking water installations. Functional requirements and test methods
- BS-EN-14095 - Water conditioning equipment inside buildings. Electrolytic treatment with aluminium anodes. Requirements for performance, safety and testing
- BS-EN-14154-1 - Water meters. General requirements
- BS-EN-14154-2 - Water meters
- BS-EN-14154-3 - Water meters. Test methods and equipment
- BS-EN-14154-4 - Water meters
- BS-EN-14367 - Non controllable backflow preventer with different pressure zones. Family C, type A
- BS-EN-1444 - Fibre-cement pipelines. Guide for laying and on-site work practices
- BS-EN-1452-1 - Plastics piping systems for water supply. Unplasticized poly (vinyl chloride) (PVC-U). General
- BS-EN-1452-2 - Plastics piping systems for water supply. Unplasticized poly (vinyl chloride) (PVC-U). Pipes
- BS-EN-1452-3 - Plastics piping systems for water supply. Unplasticized poly (vinyl chloride) (PVC-U). Fittings
- BS-EN-1452-4 - Plastics piping systems for water supply. Unplasticized poly(vinyl chloride) (PVC-U)
- BS-EN-1452-5 - Plastics piping systems for water supply. Unplasticized poly (vinyl chloride) (PVC-U). Fitness for purpose of the system
- BS-EN-14622 - Devices to prevent pollution by backflow of potable water. Air gap with circular overflow (restricted). Family A, type F
- BS-EN-14623 - Devices to prevent pollution by backflow of potable water. Air gaps with minimum circular overflow (verified by test or measurement). Family A, type G
- BS-EN-14652 - Water conditioning equipment inside buildings. Membrane separation devices. Requirements for performance, safety and testing
- BS-EN-14743 - Water conditioning equipment inside buildings. Softeners. Requirements for performance, safety and testing
- BS-EN-14812 - Water conditioning equipment inside buildings. Chemical dosing systems. Pre-set dosing systems. Requirements for performance, safety and testing
- BS-EN-1487 - Building valves. Hydraulic safety groups. Tests and requirements
- BS-EN-1488 - Building valves. Expansion groups. Tests and requirements
- BS-EN-1488-TC - Tracked Changes. Building valves. Expansion groups. Tests and requirements
- BS-EN-1489 - Building valves. Pressure safety valves. Tests and requirements
- BS-EN-14897 - Water conditioning equipment inside buildings. Devices using mercury low-pressure ultraviolet radiators. Requirements for performance, safety and testing
- BS-EN-14898 - Water conditioning equipment inside buildings. Active media filters. Requirements for performance, safety and testing
- BS-EN-1490 - Building valves. Combined temperature and pressure relief valves. Tests and requirements
- BS-EN-1491 - Building valves. Expansion valves. Tests and requirements
- BS-EN-1491-TC - Tracked Changes. Building valves. Expansion valves. Tests and requirements
- BS-EN-1508 - Water supply. Requirements for systems and components for the storage of water
- BS-EN-15092 - Building valves. Inline hot water supply tempering valves. Tests and requirements
- BS-EN-15096 - Devices to prevent pollution by backflow of potable water. Hose Union anti-vacuum valves. DN 15 to DN 25 inclusive Family H, type B and type D. General technical specification
- BS-EN-15161 - Water conditioning equipment inside buildings. Installation, operation, maintenance and repair
- BS-EN-15219 - Water conditioning equipment inside buildings. Nitrate removal devices. Requirements for performance, safety and testing
- BS-EN-1567 - Building valves. Water pressure reducing valves and combination water reducing valves. Requirements and tests.
- BS-EN-15848 - Water conditioning equipment inside buildings. Adjustable chemical dosing systems. Requirements for performance, safety and testing
- BS-EN-1717 - Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow
- BS-EN-17800 - Life cycle cost (LCC) and life cycle assessment (LCA) for CO2 emissions in ductile iron pipe systems
- BS-EN-17821 - Building valves. Frost resistant taps for outdoor use (FRT). General technical specification
- BS-EN-488 - District heating pipes. Bonded single pipe systems for directly buried hot water networks. Factory made steel valve assembly for steel service pipes, polyurethane thermal insulation and a casing of polyethylene
- BS-EN-489 - District heating pipes. Preinsulated bonded pipe systems for directly buried hot water networks. Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene
- BS-EN-489-1 - District heating pipes. Bonded single and twin pipe systems for buried hot water networks
- BS-EN-60335-2-67 - Household and similar electrical appliances. Safety
- BS-EN-61770-TC - Electric appliances connected to the water mains. Avoidance of backsiphonage and failure of hose-sets
- BS-EN-751-3-TC - Tracked Changes. Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water
- BS-EN-805 - Water supply. Requirements for systems and components outside buildings
- BS-EN-806-1 - Specifications for installations inside buildings conveying water for human consumption
- BS-EN-806-2 - Specifications for installations inside buildings conveying water for human consumption
- BS-EN-806-3 - Specifications for installations inside buildings conveying water for human consumption
- BS-EN-806-4 - Specifications for installations inside buildings conveying water for human consumption
- BS-EN-806-5 - Specifications for installations inside buildings conveying water for human consumption
- BS-EN-ISO-11177 - Vitreous and porcelain enamels. Inside and outside enamelled valves and pressure pipe fittings for untreated and potable water supply. Quality requirements and testing
- BS-EN-ISO-13056 - Plastics piping systems. Pressure systems for hot and cold water. Test method for leaktightness under vacuum
- BS-EN-ISO-13845 - Plastics piping systems. Elastomeric-sealing-ring-type socket joints for use with thermoplastic pressure pipes. Test method for leaktightness under internal pressure and with angular deflection
- BS-EN-ISO-13845-TC - Tracked Changes. Plastics piping systems. Elastomeric-sealing-ring-type socket joints for use with thermoplastic pressure pipes. Test method for leaktightness under internal pressure and with angular deflection
- BS-EN-ISO-1452-1 - Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC U)
- BS-EN-ISO-1452-2 - Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC U)
- BS-EN-ISO-1452-3 - Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC-U)
- BS-EN-ISO-1452-4 - Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC U)
- BS-EN-ISO-1452-5 - Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC U)
- BS-EN-ISO-15874-1 - Plastics piping systems for hot and cold water installations. Polypropylene (PP)
- BS-EN-ISO-15874-2 - Plastics piping systems for hot and cold water installations. Polypropylene (PP)
- BS-EN-ISO-15874-3 - Plastics piping systems for hot and cold water installations. Polypropylene (PP)
- BS-EN-ISO-15874-5 - Plastics piping systems for hot and cold water installations. Polypropylene (PP)
- BS-EN-ISO-15875-1 - Plastics piping systems for hot and cold water installations. Crosslinked polyethylene (PE-X)
- BS-EN-ISO-15875-2 - Plastics piping systems for hot and cold water installations. Crosslinked polyethylene (PE-X)
- BS-EN-ISO-15875-5 - Plastics piping systems for hot and cold water installations. Crosslinked polyethylene (PE-X)
- BS-EN-ISO-15876-1 - Plastics piping systems for hot and cold water installations. Polybutene (PB)
- BS-EN-ISO-15876-2 - Plastics piping systems for hot and cold water installations. Polybutene (PB)
- BS-EN-ISO-15876-3 - Plastics piping systems for hot and cold water installations. Polybutene (PB)
- BS-EN-ISO-15876-3-TC - Tracked Changes. Plastics piping systems for hot and cold water installations. Polybutene (PB)
- BS-EN-ISO-15876-5 - Plastics piping systems for hot and cold water installations. Polybutene (PB)
- BS-EN-ISO-15876-5-TC - Tracked Changes. Plastics piping systems for hot and cold water installations. Polybutene (PB)
- BS-EN-ISO-15877-1 - Plastics piping systems for hot and cold water installations. Chlorinated poly(vinyl chloride) (PVC-C)
- BS-EN-ISO-15877-2 - Plastics piping systems for hot and cold water installations. Chlorinated poly(vinyl chloride) (PVC-C)
- BS-EN-ISO-15877-3 - Plastics piping systems for hot and cold water installations. Chlorinated poly(vinyl chloride) (PVC-C)
- BS-EN-ISO-15877-5 - Plastics piping systems for hot and cold water installations. Chlorinated poly(vinyl chloride) (PVC-C)
- BS-EN-ISO-21003-1 - Multilayer piping systems for hot and cold water installations inside buildings
- BS-EN-ISO-21003-2 - Multilayer piping systems for hot and cold water installations inside buildings
- BS-EN-ISO-21003-3 - Multilayer piping systems for hot and cold water installations inside buildings
- BS-EN-ISO-21003-5 - Multilayer piping systems for hot and cold water installations inside buildings
- BS-EN-ISO-22391-1 - Plastics piping systems for hot and cold water installations. Polyethylene of raised temperature resistance (PE-RT)
- BS-EN-ISO-22391-2 - Plastics piping systems for hot and cold water installations. Polyethylene of raised temperature resistance (PE-RT)
- BS-EN-ISO-22391-3 - Plastics piping systems for hot and cold water installations. Polyethylene of raised temperature resistance (PE-RT)
- BS-EN-ISO-22391-5 - Plastics piping systems for hot and cold water installations. Polyethylene of raised temperature resistance (PE-RT)
- BS-EN-ISO-3822-1 - Acoustics. Laboratory tests on noise emission from appliances and equipment used in water supply installations
- BS-EN-ISO-3822-3 - Acoustics. Laboratory tests on noise emission from appliances and equipment used in water supply installations
- BS-EN-ISO-3822-4 - Acoustics. Laboratory tests on noise emission from appliances and equipment used in water supply installations
- BS-EN-ISO-4064-1 - Water meters for cold potable water and hot water
- BS-EN-ISO-4064-1-TC - Tracked Changes. Water meters for cold potable water and hot water
- BS-EN-ISO-4064-2 - Water meters for cold potable water and hot water
- BS-EN-ISO-4064-2-TC - Tracked Changes. Water meters for cold potable water and hot water
- BS-EN-ISO-4064-3 - Water meters for cold potable water and hot water
- BS-EN-ISO-4064-4 - Water meters for cold potable water and hot water
- BS-EN-ISO-4064-5 - Water meters for cold potable water and hot water
- BS-EN-ISO-4064-5-TC - Tracked Changes. Water meters for cold potable water and hot water
- BS-EN-ISO-8795 - Plastics piping systems for the transport of water intended for human consumption. Migration assessment. Determination of migration values of plastics pipes and fittings and their joints
- BS-ISO-10508 - Plastics piping systems for hot and cold water installations. Guidance for classification and design
- BS-ISO-10639 - Plastics piping systems for pressure and non-pressure water supply. Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
- BS-ISO-16422 - Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure. Specifications
- BS-ISO-21053 - Life cycle analysis and recycling of ductile iron pipes for water applications
- BS-ISO-23711 - Elastomeric seals. Requirements for materials for pipe joint seals used in water and drainage applications. Thermoplastic elastomers
- BS-ISO-2531 - Ductile iron pipes, fittings, accessories and their joints for water applications
- BS-ISO-4064-2 - Measurement of water flow in closed conduits. Meters for cold potable water
- BS-ISO-4427-1 - Plastics piping systems for water supply and for drainage and sewerage under pressure. Polyethylene (PE)
- BS-ISO-4427-2 - Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE)
- BS-ISO-4427-3 - Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE)
- BS-ISO-4427-5 - Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE)
- BS-ISO-4633 - Rubber seals. Joint rings for water supply, drainage and sewerage pipelines. Specification for materials
- DD-CEN-12201-7 - Plastics piping systems for water supply. Polyethylene (PE)
- DD-CEN-14632 - Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure. Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP). Guidance for the assessment of conformity
- DD-CEN-ISO-15874-7 - Plastics piping systems for hot and cold water installations. Polypropylene (PP)
- DD-CEN-ISO-15875-7 - Plastics piping systems for hot and cold water installations. Crosslinked polyethylene (PE-X)
- DD-CEN-ISO-15876-7 - Plastics piping systems for hot and cold water installations. Polybutylene (PB)
- DD-CEN-ISO-15877-7 - Plastics piping systems for hot and cold water installations. Chlorinated poly(vinyl chloride) (PVC-C)
- DD-CEN-ISO-22391-7 - Plastics piping systems for hot and cold water installations. Polyethylene of raised temperature resistance (PE-RT)
- DD-ENV-12108 - Plastics piping systems. Guidance for the installation inside buildings of pressure systems for hot and cold water intended for human consumption
- DD-ENV-1452-6 - Plastics piping systems for water supply. Unplasticized poly(vinyl chloride) (PVC-U)
- DD-ENV-1452-7 - Guidance for the Assessment of Conformity
- HB-10178 - Hot and Cold Water Supply
- PD-855468 - Guide to the flushing and disinfection of services supplying water for domestic use within buildings and their curtilages
- PD-CEN-12108 - Plastics piping systems. Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption
- PD-CEN-12201-7 - Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE)
- PD-CEN-1452-7 - Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC-U)
- PD-CEN-14632 - Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Guidance for the assessment of conformity
- PD-CEN-14632-TC - Tracked Changes. Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Guidance for the assessment of conformity
- PD-CEN-14807 - Plastics piping systems. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Guidance for the structural analysis of buried GRP-UP pipelines
- PD-CEN-ISO-15874-7 - Plastics piping systems for hot and cold water installations. Polypropylene (PP)
- PD-CEN-ISO-15875-7 - Plastics piping systems for hot and cold water installations. Crosslinked polyethylene (PE-X)
- PD-CEN-ISO-21003-7 - Multilayer piping systems for hot and cold water installations inside buildings
- PD-CEN-ISO-22391-7 - Plastics piping systems for hot and cold water installations. Polyethylene of raised temperature resistance (PE-RT)
- PD-CEN-ISO-27165 - Thermoplastics piping systems. Guidance for definitions of wall constructions for pipes
- PD-ISO-16422-3 - Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure
- PD-ISO-24520 - Service activities relating to drinking water supply systems and wastewater systems. Crisis management. Good practice for technical aspects
- PD-ISO-4191 - Plastics piping systems for water supply. Unplasticized poly(vinyl chloride)(PVC-U) and oriented PVC-U (PVC-O). Guidance for installation
- PD-ISO-4340 - Water aggressiveness evaluation and optimized lining choice
IEC:
- IEC-61770 - Electric appliances connected to the water mains - Avoidance of backsiphonage and failure of hose-sets
- IEC-61770-1 - Amendment 1 - Electric appliances connected to the water mains - Avoidance of backsiphonage and failure of hose-sets
- IEC-61770-2 - Amendment 2: Electric Appliances Connected To the Water Mains - Avoidance of Backsipho
ISO:
- ISO-10385-1 - Measurement of water flow in closed conduits -- Meters for hot water -- Part 1: Specifications
- ISO-10508 - Plastics piping systems for hot and cold water installations - Guidance for classification and design
- ISO-10508-AM1 - - Amendment 1
- ISO-10639 - Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
- ISO-10639-AM1 - Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin - Amendment 1
- ISO-11177 - Vitreous and porcelain enamels - Inside and outside enamelled valves and pressure pipe fittings for untreated and potable water supply - Quality requirements and testing
- ISO-13056 - Plastics piping systems - Pressure systems for hot and cold water - Test method for leaktightness under vacuum
- ISO-13844 - Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with plastic pipes - Test method for leaktightness under negative pressure, angular deflection and deformation
- ISO-13845 - Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with thermoplastic pressure pipes - Test method for leaktightness under internal pressure and with angular deflection
- ISO-14236 - Plastics pipes and fittings - Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems
- ISO-1452-1 - Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: General
- ISO-1452-2 - Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Pipes
- ISO-1452-3 - Plastics Piping Systems for Water Supply and for Buried and Above-Ground Drainage and Sewerage Under Pressure - Unplasticized Poly(Vinyl Chloride) (PVC-U) - Part 3: Fittings
- ISO-1452-4 - Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves
- ISO-1452-5 - Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 5: Fitness for purpose of the system
- ISO-15874-1 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General
- ISO-15874-1-1 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: GeneralAmendment 1
- ISO-15874-1-AM1 - - Amendment 1: Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General - Amendment 1: Impact test
- ISO-15874-2 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes
- ISO-15874-2-1 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: PipesAmendment 1
- ISO-15874-2-AM1 - - Amendment 1
- ISO-15874-2-AM2 - - Amendment 2: Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes - Amendment 2: Impact test
- ISO-15874-3 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings
- ISO-15874-3-AM1 - - Amendment 1
- ISO-15874-3-AM2 - - Amendment 2: Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings - Amendment 2
- ISO-15874-5 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 5: Fitness for purpose of the system
- ISO-15874-5-AM1 - - Amendment 1
- ISO-15874-7 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 7: Guidance for the assessment of conformity
- ISO-15875-1 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 1: General
- ISO-15875-1-1 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 1: General - Amendment 1
- ISO-15875-2 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 2: Pipes
- ISO-15875-2-1 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 2: Pipes - Amendment 1
- ISO-15875-2-AM2 - - Amendment 2
- ISO-15875-3 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings
- ISO-15875-3-AM1 - - Amendment 1
- ISO-15875-3-AM2 - - Amendment 2: Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings - Amendment 2
- ISO-15875-5 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 5: Fitness for purpose of the system
- ISO-15875-5-AM1 - - Amendment 1
- ISO-15875-7 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 7: Guidance for the assessment of conformity
- ISO-15876-1 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 1: General
- ISO-15876-1-1 - Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 1: General - Amendment 1
- ISO-15876-2 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 2: Pipes
- ISO-15876-2-1 - Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 2: Pipes - Amendment 1
- ISO-15876-2-AM1 - - Amendment 1
- ISO-15876-3 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 3: Fittings
- ISO-15876-3-AM1 - - Amendment 1
- ISO-15876-3-AM2 - - Amendment 2: Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 3: Fittings - Amendment 2
- ISO-15876-5 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system
- ISO-15876-5-AM1 - - Amendment 1
- ISO-15876-7 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 7: Guidance for the assessment of conformity
- ISO-15877-1 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: General
- ISO-15877-1-AM1 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: General - Amendment 1
- ISO-15877-2 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Pipes
- ISO-15877-2-AM1 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Pipes - Amendment 1
- ISO-15877-2-AM2 - - Amendment 2
- ISO-15877-3 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings
- ISO-15877-3-AM1 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings - Amendment 1
- ISO-15877-3-AM2 - - Amendment 2: Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings - Amendment 2
- ISO-15877-5 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system
- ISO-15877-5-AM1 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system - Amendment 1
- ISO-15877-5-AM2 - - Amendment 2
- ISO-15877-7 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity
- ISO-16422 - Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure - Specifications
- ISO-16422-3 - Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure - Part 3: Fittings
- ISO-16631 - Ductile iron pipes, fittings, accessories and their joints compatible with plastic (PVC or PE) piping systems, for water applications and for plastic pipeline connections, repair and replacement
- ISO-21003-1 - Multilayer piping systems for hot and cold water installations inside buildings - Part 1: General
- ISO-21003-2 - Multilayer piping systems for hot and cold water installations inside buildings - Part 2: Pipes
- ISO-21003-2-AM1 - Multilayer piping systems for hot and cold water installations inside buildings - Part 2: Pipes - Amendment 1
- ISO-21003-3 - Multilayer piping systems for hot and cold water installations inside buildings - Part 3: Fittings
- ISO-21003-3-AM1 - - Amendment 1: Multilayer piping systems for hot and cold water installations inside buildings - Part 3: Fittings - Amendment 1
- ISO-21003-5 - Multilayer piping systems for hot and cold water installations inside buildings - Part 5: Fitness for purpose of the system
- ISO-21003-7 - Multilayer piping systems for hot and cold water installations inside buildings - Part 7: Guidance for the assessment of conformity
- ISO-21003-7-AM1 - Multilayer piping systems for hot and cold water installations inside buildings - Part 7: Guidance for the assessment of conformity - Anendment 1
- ISO-21053 - Life cycle analysis and recycling of ductile iron pipes for water applications
- ISO-22158 - Input/output protocols and electronic interfaces for water meters - Requirements
- ISO-22391-1 - Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 1: General
- ISO-22391-2 - Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 2: Pipes
- ISO-22391-2-AM1 - - Amendment 1
- ISO-22391-3 - Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 3: Fittings
- ISO-22391-3-AM1 - - Amendment 1
- ISO-22391-3-AM2 - - Amendment 2: Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 3: Fittings - Amendment 2
- ISO-22391-5 - Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 5: Fitness for purpose of the system
- ISO-22391-5-AM1 - - Amendment 1
- ISO-22391-7 - Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 7: Guidance for the assessment of conformity
- ISO-23711 - Elastomeric seals - Requirements for materials for pipe joint seals used in water and drainage applications - Thermoplastic elastomers
- ISO-24520 - Service activities relating to drinking water supply systems and wastewater systems - Crisis management - Good practice for technical aspects
- ISO-2531 - Ductile iron pipes, fittings, accessories and their joints for water applications
- ISO-25780 - Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin - Pipes with flexible joints intended to be installed using jacking techniques
- ISO-27165 - Thermoplastics piping systems - Guidance for definitions of wall constructions for pipes
- ISO-3114 - Unplasticized polyvinyl chloride (PVC) pipes for potable water supply - Extractability of lead and tin - Test method
- ISO-3822-1 - Acoustics -- Laboratory tests on noise emission from appliances and equipment used in water supply installations -- Part 1: Method of measurement
- ISO-3822-1-1 - Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 1: Method of measurement - Amendment 1: Measurement uncertainty
- ISO-3822-2 - Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 2: Mounting and operating conditions for draw-off taps and mixing valves
- ISO-3822-3 - Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 3: Mounting and operating conditions for in-line valves and appliances
- ISO-3822-3/A1 - Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 3: Mounting and operating conditions for in-line valves and appliances - Amendment 1
- ISO-3822-4 - Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 4: Mounting and operating conditions for special appliances
- ISO-4064-1 - Water meters for cold potable water and hot water - Part 1: Metrological and technical requirements
- ISO-4064-2 - Water meters for cold potable water and hot water - Part 2: Test methods
- ISO-4064-3 - Water meters for cold potable water and hot water - Part 3: Test report format
- ISO-4064-4 - Water meters for cold potable water and hot water - Part 4: Non-metrological requirements not covered in ISO 4064-1
- ISO-4064-5 - Water meters for cold potable water and hot water - Part 5: Installation requirements
- ISO-4191 - Plastics piping systems for water supply - Unplasticized poly(vinyl chloride)(PVC-U) and oriented PVC-U (PVC-O) - Guidance for installation
- ISO-4340 - Water aggressiveness evaluation and optimized lining choice
- ISO-4422-1 - Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply - Specifications - Part 1: General
- ISO-4422-2 - Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply - Specifications - Part 2: Pipes (with or without integral sockets)
- ISO-4422-3 - Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply - Specifications - Part 3: Fittings and joints
- ISO-4422-4 - Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply - Specifications - Part 4: Valves and ancillary equipment
- ISO-4422-5 - Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply - Specifications - Part 5: Fitness for purpose of the system
- ISO-4427 - Polyethylene (PE) pipes for water supply - Specifications
- ISO-4427-1 - Plastics piping systems for water supply and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General
- ISO-4427-1-AM1 - - Amendment 1: Melt mass-flow rate (MFR) for PE 80 and PE 100
- ISO-4427-2 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes
- ISO-4427-2-AM1 - - Amendment 1: Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes - Amendment 1
- ISO-4427-3 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings
- ISO-4427-5 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system
- ISO-4633 - Rubber seals - Joint rings for water supply, drainage and sewerage pipelines - Specification for materials
- ISO-559 - Steel tubes for water and sewage
- ISO-6992 - Unplasticized polyvinyl chloride (PVC-U) pipes for drinking water supply - Extractability of cadmium and mercury occurring as impurities
- ISO-7858-1 - Measurement of water flow in closed conduits -- Combination meters for cold potable water -- Part 1: Specifications
- ISO-7858-2 - Measurement of water flow in closed conduits -- Combination meters for cold potable water -- Part 2: Installation requirements
- ISO-7858-3 - Measurement of water flow in closed conduits -- Meters for cold potable water -- Combination meters -- Part 3: Test methods
- ISO-8795 - Plastics piping systems for the transport of water intended for human consumption -- Migration assessment -- Determination of migration values of plastics pipes and fittings and their joints
Other SDOs:
- AS/NZS-9201.7 - Model General by Laws - Water Supply
- BS-8680 EXPERT COMM KIT - Water quality. Water safety plans. Code of practice
- CEN-ISO-15874-7 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 7: Guidance for the assessment of conformity
- CEN-ISO-15875-7 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 7: Guidance for the assessment of conformity
- CEN-ISO-15876-7 - Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 7: Guidance for the assessment of conformity
- CEN-ISO-15877-7 - Plastics piping systems for hot and cold water installations - Chlorinated poly (vinyl chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity
- CEN-ISO-22391-7 - Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 7: Guidance for the assessment of conformity
- DIN-EN-12201-1 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General
- DIN-EN-12201-2 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes; German version EN 12201-2:2011+A1:2013
- DIN-EN-12201-3 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings; German version EN 12201-3:2011+A1:2012
- DIN-EN-12201-5 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system
- DIN-EN-12502-1 - Part 1: General, Protection of Metallic Materials Against Corrosion, Guidance on the A
- DIN-EN-12502-2 - Part 2: Influencing Factors for Copper & Copper Alloys, Protection of Metallic Materia
- DIN-EN-12502-3 - Part 3: Influencing Factors for Hot-Dip Galvanized Ferrous Materials, Protection of Me
- DIN-EN-12502-4 - Part 4: Influencing Factors for Stainless Steels, Protection of Metallic Materials AGA
- DIN-EN-12502-5 - Part 5: Influencing Factors for Cast Iron, Unalloyed & Low-Alloy Steels, Protection Of
- DIN-EN-13443-1 - Part 1: Particle Rating 80 Um To 150 Um - Requirements for Performances, Safety & Test
- DIN-EN-13443-2 - Part 2: Particle Rating 1 Um To Less Than 80 Um - Requirements for Performance, Safety
- DIN-EN-14154-1 - Water meters - Part 1: General requirements; German version EN 14154-1:2005+A2:2011
- DIN-EN-14154-2 - Water meters - Part 2: Installation and conditions of use; German version EN 14154-2:2005+A2:2011
- DIN-EN-14154-3 - Water meters - Part 3: Test methods and equipment; German version EN 14154-3:2005+A2:2011
- DIN-EN-14367 - Non Controllable Backflow Preventer With Different Pressure Zones, Family C, Type A
- DIN-EN-14622 - Air Gaps With Circular Overflow (Restricted) - Family a, Type F, Devices To Prevent Po
- DIN-EN-14623 - Air Gaps With Minimum Circular Overflow (Verified by Test or Measurement) - Family a,
- DIN-EN-14652 - Water Conditioning Equipment Inside Buildings - Membrane Separation Devices - Requirem
- DIN-EN-14743 - Water Conditioning Equipment Inside Buildings - Softeners - Requirements for Performa
- DIN-EN-14812 - Water Conditioning Equipment Inside Buildings - Chemical Dosing Systems - Pre-Set Dosi
- DIN-EN-14897 - Water Conditioning Equipment Inside Buildings - Devices Using Mercury Low-Pressure Ult
- DIN-EN-14898 - Water Conditioning Equipment Inside Buildings - Active Media Filters - Requirements Fo
- DIN-EN-15161 - Water Conditioning, Equipment Inside Buildings - Installation, Operation, Maintenance
- DIN-EN-15219 - Water Equipment Inside Buildings - Nitrate Removal Devices - Requirements for Performa
- DIN-EN-806-2 - Specification for installations inside buildings conveying water for human consumption - Part 2: Design
- DIN-EN-806-3 - Part 3: Pipe Sizing - Simplified Method, Specifications for Installations for Install
- DIN-EN-ISO-15874-1 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General (ISO 15874-1:2013)
- DIN-EN-ISO-15874-2 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes (ISO 15874-2:2013)
- DIN-EN-ISO-15874-3 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings (ISO 15874-3:2013)
- DIN-EN-ISO-15874-5 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 5: Fitness for purpose of the system (ISO 15874-5:2013)
- DIN-EN-ISO-15875-1 - Part 1: General, Plastics Piping Systems for Hot & Cold Water Installations - Crosslin
- DIN-EN-ISO-15875-2 - Part 2: Pipes, Plastics Piping Systems for Hot & Cold Waterinstallations - Crosslinke
- DIN-EN-ISO-15876-1 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 1: General
- DIN-EN-ISO-15876-2 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 2: Pipes
- DIN-EN-ISO-15876-3 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 3: Fittings
- DIN-EN-ISO-15876-5 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system
- DIN-EN-ISO-15877-1 - Part 1: General, Plastics Piping Systems for Hot & Cold Water Installations - Chlorina
- DIN-EN-ISO-15877-2 - Part 2: Pipes, Plastics Piping Systems for Hot & Cold Water Installations - Chlorinat
- DIN-EN-ISO-15877-3 - Part 3: Fittings, Plastics Piping Systems for Hot & Cold Water Installations - Chlorin
- DIN-EN-ISO-15877-5 - Part 5: Fitness for Purpose of the System, Plastics Piping Systems for Hot & Cold Wate
- EN-1213 - Building Valves - Copper Alloy Stopvalves for Potable Water Supply in Buildings - Tes
- EN-12201-4 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves
- EN-12502-1 - Part 1: General, Protection of Metallic Materials Against Corrosion, Guidance on the A
- EN-12502-2 - Part 2: Influencing Factors for Copper & Copper Alloys, Prottection of Metallic Materi
- EN-12502-3 - Part 3: Influencing Factors for Hot-Dip Galvanized Ferrous Materials, Protection of Me
- EN-12502-4 - Part 4: Influencing Factors for Stainless Steels, Protection of Metallic Materials AGA
- EN-12502-5 - Part 5: Influencing Factors for Cast Iron, Unalloyed & Low-Alloy Steels, Protection Of
- EN-12729 - Devices To Prevent Pollution by Backflow of Potable Water, Controllable Backflow Prev
- EN-13076 - Devices To Prevent Pollution by Backflow of Potable Water, Unrestricted Air Gap - Fami
- EN-13077 - Devices To Prevent Pollution by Backflow of Potable Water - Air Gap With Non-Circular
- EN-13443-1 - Part 1: Particle Rating 80 Um To 150 Um - Requirements for Performances, Safety & Test
- EN-13443-2 - Part 2: Particle Rating 1 Um To Less Than 80 Um - Requirements for Performance, Safety
- EN-13618 - Flexible hose assemblies in drinking water installations - Functional requirements and test methods
- EN-14154-1 - Water meters - Part 1: General requirements
- EN-14154-2 - Water meters - Part 2: Installation and conditions of use
- EN-14154-3 - Water meters - Part 3: Test methods and equipment
- EN-14154-4 - Water meters - Part 4: Additional functionalities
- EN-14367 - Non Controllable Backflow Preventer With Different Pressure Zones, Family C, Type A
- EN-1452-1 - Plastics Piping Systems for Water Supply - Unplasticized Poly(Vinyl Chloride) (PVC-U)
- EN-1452-2 - Plastics Piping Systems for Water Supply - Unplasticized Poly(Vinyl Chloride) (PVC-U)
- EN-1452-3 - Plastics Piping Systems for Water Supply - Unplasticized Poly(Vinyl Chloride) (PVC-U)
- EN-1452-4 - Plastics Piping Systems for Water Supply - Unplasticized Poly(Vinyl Chloride) (PVC-U)
- EN-1452-5 - Part 5: Fitness for Purpose of the System, Plastics Piping Systems for Water Supply -
- EN-14622 - Air Gaps With Circular Overflow (Restricted) - Family a, Type F, Devices To Prevent Po
- EN-14623 - Air Gaps With Minimum Circular Overflow (Verified by Test or Measurement) - Family a,
- EN-14652 - Water Conditioning Equipment Inside Buildings - Membrane Separation Devices - Requirem
- EN-14743 - Water Conditioning Equipment Inside Buildings - Softeners - Requirements for Performa
- EN-14812 - Water Conditioning Equipment Inside Buildings-Chemical Dosing Systems-Pre-Set Dosing S
- EN-1487 - Building valves - Hydraulic safety groups - Tests and requirements
- EN-14897 - Water Conditioning Equipment Inside Buildings - Devices Using Mercury Low-Pressure Ult
- EN-14898 - Water Conditioning Equipment Inside Buildings - Active Media Filters - Requirements Fo
- EN-1508 - Water Supply, Requirements for Systems & Components for the Storage of Water
- EN-15092 - Building Valves, Inline Hot Water Supply Tempering Valves, Tests & Requirements
- EN-15161 - Water Conditioning Equipment Inside Buildings - Installation, Operation, Maintenance &
- EN-15219 - Water Equipment Inside Buildings, Nitrate Removal Devices, Requirements for Performanc
- EN-15848 - Water Conditioning Equipment Inside Buildings - Adjustable Chemical Dosing Systems - R
- EN-1717 - Protection Against Pollution of Potable Water in Water Installations & General Require
- EN-61770/A1 - Electric appliances connected to the water mains - Avoidance of backsiphonage and failure of hose-sets (IEC 61770:2008/A1:2015, modified)
- EN-806-2 - Part 2: Design, Specification for Installations Inside Buildings Conveying Water for H
- EN-806-3 - Part 3: Pipe Sizing - Simplified Method, Specifications for Installations Inside Buil
- EN-806-4 - Part 4: Installation, Specifications for Installations Inside Buildings Conveying Wate
- EN-806-5 - Specifications for installations inside buildings conveying water for human consumption - Part 5: Operation and maintenance
- EN-ISO-11177 - Vitreous and porcelain enamels - Inside and outside enamelled valves and pressure pipe fittings for untreated and potable water supply - Quality requirements and testing
- EN-ISO-13056 - Plastics piping systems - Pressure systems for hot and cold water - Test method for leaktightness under vacuum
- EN-ISO-13844 - Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with plastic pressure pipes - Test method for leaktightness under negative pressure, angular deflection and deformation
- EN-ISO-13845 - Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with thermoplastic pressure pipes - Test method for leaktightness under internal pressure and with angular deflection
- EN-ISO-1452-1 - Part 1: General, Plastics Piping Systems for Water Supply & for Buried & Above-Ground
- EN-ISO-1452-2 - Part 2: Pipes, Plastics Piping Systems for Water Supply & for Buried & Above-Ground Dr
- EN-ISO-1452-3 - Part 3: Fittings, Plastics Piping Systems for Water Supply & for Buried & Above-Ground
- EN-ISO-1452-4 - Part 4: Valves, Plastics Piping Systems for Water Supply & for Buried & Above-Ground D
- EN-ISO-1452-5 - Part 5: Fitness for Purpose of the System, Plastics Piping Systems for Water Supply &
- EN-ISO-15874-1 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General (ISO 15874-1:2013)
- EN-ISO-15874-2 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes (ISO 15874-2:2013)
- EN-ISO-15874-3 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings (ISO 15874-3:2013)
- EN-ISO-15874-5 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 5: Fitness for purpose of the system (ISO 15874-5:2013)
- EN-ISO-15875-1 - Part 1: General, Plastics Piping Systems for Hot & Cold Water Installations - Crosslin
- EN-ISO-15875-2 - Part 2: Pipes, Plastics Piping Systems for Hot & Cold Water Installations - Crosslink
- EN-ISO-15876-1 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 1: General
- EN-ISO-15876-2 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 2: Pipes
- EN-ISO-15876-3 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 3: Fittings
- EN-ISO-15876-5 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system
- EN-ISO-15877-1 - Part 1: General, Plastics Piping Systems for Hot & Cold Water Installations - Chlorina
- EN-ISO-15877-3 - Part 3: Fittings, Plastics Piping Systems for Hot & Cold Water Installations - Chlorin
- EN-ISO-15877-5 - Part 5: Fitness for Purpose of the System, Plastics Piping Systems for Hot & Cold Wate
- EN-ISO-21003-1 - Part 1: General, Multilayer Piping Systems for Hot & Cold Water Installations Inside B
- EN-ISO-21003-2 - Part 2: Pipes, Multilayer Piping Systems for Hot & Cold Water Installations Inside Bui
- EN-ISO-21003-3 - Multilayer Piping Systems for Hot & Cold Water Installations Inside Buildings, Fitting
- EN-ISO-21003-5 - Multilayer Piping Systems for Hot & Cold Water Installations Inside Buildings, Fitness
- EN-ISO-22391-1 - Part 1: General, Plastics Piping Systems for Hot & Cold Water Installations - Polyethy
- EN-ISO-22391-2 - Part 2: Pipes, Plastics Piping Systems for Hot & Cold Water Installations - Polyethyl
- EN-ISO-22391-3 - Part 3: Fittings, Plastics Piping Systems for Hot & Cold Water Installations - Polyeth
- EN-ISO-22391-5 - Part 5: Fitness for Purpose of the System, Plastics Piping Systems for Hot & Cold Wate
- EN-ISO-3822-3 - Part 3: Mounting & Operating Conditions for In-Line Valves & Appliances, Acoustics - L
- EN-ISO-3822-4 - Acoustics, Laboratory Tests on Noise Emission From Appliances & Equipment Used in Wate
- EN-ISO-4064-1 - Water meters for cold potable water and hot water - Part 1: Metrological and technical requirements
- EN-ISO-4064-2 - Water meters for cold potable water and hot water - Part 2: Test methods
- EN-ISO-4064-3 - Water meters for cold potable water and hot water - Part 3: Test report format
- EN-ISO-4064-4 - Water meters for cold potable water and hot water - Part 4: Non-metrological requirements not covered in ISO 4064-1 (ISO 4064-4:2014)
- EN-ISO-4064-5 - Water meters for cold potable water and hot water - Part 5: Installation requirements
- JIS-K-6770-A3 - Crosslinked polyethylene (PE-X) pipe fittings (Amendment 3)
- JIS-K-6777-A2 - Chlorinated poly (vinyl chloride) (PVC-C) pipe fittings for hot and cold water supply (Amendment 2)
- JIS-K-6779-A2 - Polybutene (PB) pipe fittings (Amendment 2)
- JIS-K-6787/A2 - Crosslinked polyethylene (PE-X) pipes for water supply (Amendment 2)
- JIS-K-6788-A2 - Crosslinked polyethylene (PE-X) pipe fittings for water supply (Amendment 2)
- JIS-K-6793-A2 - Polybutene (PB) pipe fittings for water supply (Amendment 2)
- JIS-S-3200-1 - Equipment to water supply service -- Test methods of hydrostatic pressure
- JIS-S-3200-1-AM1 - Equipment for water supply service -- Test methods of hydrostatic pressure (Amendment 1)
- JIS-S-3200-4-AM1 - Equipment for water supply service -- Test method of prevention from back current (Amendment 1)
- JIS-S-3200-5-AM1 - Equipment for water supply service -- Test methods of destruction by vacuum pressure (Amendment 1)
- JIS-S-3200-6-AM1 - Equipment for water supply service -- Test methods of durability (Amendment 1)
- JIS-S-3200-7-A2 - Equipment for water supply service -- Test methods of effect to water quality (Amendment 2)
- SIS-CEN-ISO-21003-7 - Multilayer piping systems for hot and cold water installations inside buildings - Part 7: Guidance for the assessment of conformity (ISO/TS 21003-7:2019)
- SIS-CEN-ISO-27165 - Thermoplastics piping systems - Guidance for definitions of wall constructions for pipes (ISO/TR 27165:2012)
- SIS-CEN-ISO/TS-15874-7 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 7: Guidance for the assessment of conformity (ISO/TS 15874-7:2003)
- SIS-CEN-ISO/TS-15875-7 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 7: Guidance for the assessment of conformity (ISO/TS 15875-7:2018)
- SIS-CEN-ISO/TS-15876-7 - Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 7: Guidance for the assessment of conformity (ISO/TS 15876-7:2003)
- SIS-CEN-ISO/TS-15877-7 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity (ISO/TS 15877-7:2009)
- SIS-CEN-ISO/TS-21003-7 - Multilayer piping systems for hot and cold water installations inside buildings - Part 7: Guidance for the assessment of conformity (ISO/TS 21003-7:2019)
- SIS-CEN-ISO/TS-22391-7 - Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 7: Guidance for the assessment of conformity (ISO/TS 22391-7:2018)
- SIS-CEN/TR-12108 - Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption
- SIS-CEN/TR-16355 - Recommendations for prevention of Legionella growth in installations inside buildings conveying water for human consumption
- SIS-CEN/TS-12201-7 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity
- SIS-CEN/TS-14632 - Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the assessment of conformity
- SIS-CEN/TS-14807 - Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the structural analysis of buried GRP-UP pipelines
- SS-820200 - Sanitary appliances - Prefabricated installation modules for wall-hung WC pans - Requirements and test methods
- SS-EN-1074-1 - Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 1: General requirements
- SS-EN-1074-4 - Valves for water supply - Fitness for purpose requirements and approriate verification tests - Part 4: Air valves
- SS-EN-1124-4 - Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for wastewater systems - Part 4: Components for vacuum drainage systems and for drainage systems on ships
- SS-EN-1213 - Building valves - Copper alloy stopvalves for potable water supply in buildings - Tests and requirements
- SS-EN-12201-1 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General
- SS-EN-12201-2 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes
- SS-EN-12201-3 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings
- SS-EN-12201-4 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves
- SS-EN-12201-5 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system
- SS-EN-12502-1 - Protection of metallic materials against corrosion - Guidance on the assessment of corrosion likelihood in water distribution and storage systems - Part 1: General
- SS-EN-12502-2 - Protection of metallic materials against corrosion - Guidance on the assessment of corrosion likelihood in water distribution and storage systems - Part 2: Influencing factors for copper and copper alloys
- SS-EN-12502-3 - Protection of metallic materials against corrosion - Guidance on the assessment of corrosion likelihood in water distribution and storage systems - Part 3: Influencing factors for hot dip galvanised ferrous materials
- SS-EN-12502-4 - Protection of metallic materials against corrosion - Guidance on the assessment of corrosion likelihood in water distribution and storage systems - Part 4: Influencing factors for stainless steels
- SS-EN-12502-5 - Protection of metallic materials against corrosion - Guidance on the assessment of corrosion likelihood in water distribution and storage systems - Part 5: Influencing factors for cast iron, unalloyed and low alloyed steel
- SS-EN-12729 - Devices to prevent pollution by backflow of potable water - Controllable backflow preventer with reduced pressure zone - Family B - Type A
- SS-EN-13077 - Devices to prevent pollution by backflow of potable water - Air gap with non-circular overflow (unrestricted) - Family A - Type B
- SS-EN-13079 - Devices to prevent pollution by backflow of potable water - Air gap with injector - Family A - Type D
- SS-EN-13443-1 - Water conditioning equipment inside buildings - Mechanical filters - Part 1: Particle rating 80 µm to 150 µm - Requirements for performances, safety and testing
- SS-EN-13443-2 - Water conditioning equipment inside buildings - Mechanical filters - Part 2: Particle rating 1 µm to less than 80 µm - Requirements for performance, safety and testing
- SS-EN-13598-2 - Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for manholes and inspection chambers
- SS-EN-13618 - Flexible hose assemblies in drinking water installations - Functional requirements and test methods
- SS-EN-14095 - Water conditioning equipment inside buildings - Electrolytic treatment systems with aluminium anodes - Requirements for performance, safety and testing
- SS-EN-14154-1 - Water meters - Part 1: General requirements
- SS-EN-14154-2 - Water meters - Part 2: Installation and conditions of use
- SS-EN-14154-3 - Water meters - Part 3: Test methods and equipment
- SS-EN-14154-4 - Water meters - Part 4: Additional functionalities
- SS-EN-14367 - Non controllable backflow preventer with different pressure zones - Family C, type A
- SS-EN-1452-5 - Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 5: Fitness for purpose of the system
- SS-EN-14622 - Devices to prevent pollution by backflow of potable water - Air gap with circular overflow (restricted) - Family A, Type F
- SS-EN-14623 - Devices to prevent pollution by backflow of potable water - Air gap with overflow (tested by vacuum measurement) - Family A, Type G
- SS-EN-14652 - Water conditioning equipment inside buildings - Membrane separation devices - Requirements for performance, safety and testing
- SS-EN-14743 - Water conditioning equipment inside buildings - Softeners - Requirements for performance, safety and testing
- SS-EN-14812 - Water conditioning equipment inside buildings - Chemical dosing systems - Pre-set dosing systems - Requirements for performance, safety and testing
- SS-EN-1487 - Building valves - Hydraulic safety groups - Tests and requirements
- SS-EN-1488 - Building valves - Expansion groups - Tests and requirements
- SS-EN-1489 - Building valves - Pressure safety valves - Tests and requirements
- SS-EN-14897 - Water conditioning equipment inside buildings - Devices using mercury low-pressure ultraviolet radiators - Requirements for performance, safety and testing
- SS-EN-14898 - Water conditioning equipment inside buildings - Active media filters - Requirements for performance, safety and testing
- SS-EN-1490 - Building valves - Combined temperature and pressure relief valves - Tests and requirements
- SS-EN-1491 - Building valves - Expansion valves - Tests and requirements
- SS-EN-15092 - Building valves - Inline hot water supply tempering valves - Tests and requirements
- SS-EN-15096 - Devices to prevent pollution by backflow of potable water - Hose Union anti-vacuum valves - DN 15 to DN 25 inclusive Family H, type B and type D - General technical specification
- SS-EN-15161 - Water conditioning equipment inside buildings - Installation, operation, maintenance and repair
- SS-EN-15219 - Water conditioning equipment inside buildings - Nitrate removal devices - Requirements for performance, safety and testing
- SS-EN-15502-2-2 - Gas-fired central heating boilers - Part 2-2: Specific standard for type B1 appliances
- SS-EN-1567 - Building valves - Water pressure reducing valves and combination water pressure reducing valves - Requirements and tests
- SS-EN-15848 - Water conditioning equipment inside buildings - Adjustable chemical dosing systems - Requirements for performance, safety and testing
- SS-EN-1717 - Protection against pollution of potable water in installations and general requirements of devices to prevent pollution backflow
- SS-EN-17800 - Life cycle cost (LCC) and life cycle assessment (LCA) for CO2 emissions in ductile iron pipe systems
- SS-EN-17821 - Building valves - Frost resistant taps for outdoor use (FRT) - General technical specification
- SS-EN-26 - Gas-fired instantaneous water heaters for the production of domestic hot water
- SS-EN-26-AM1 - Gas-fired instantaneous water heaters for the production of domestic hot water, fitted with atmospheric burners
- SS-EN-26-AM2 - Gas-fired instantaneous water heaters for the production of domestic hot water, fitted with atmospheric burners
- SS-EN-26-AM3 - Gas-fired instantaneous water heaters for the production of domestic hot water, fitted with atmospheric burners
- SS-EN-806-1 - Specifications for installations inside buildings conveying water for human consumption - Part 1: General
- SS-EN-806-1-AM1 - Specifications for installations inside buildings conveying water for human consumption - Part 1: General
- SS-EN-806-2 - Specification for installations inside buildings conveying water for human consumption - Part 2: Design
- SS-EN-806-3 - Specifications for installations inside buildings conveying water for human consumption - Part 3: Pipe sizing - Simplified method
- SS-EN-806-4 - Specifications for installations inside buildings conveying water for human consumption - Part 4: Installation
- SS-EN-806-5 - Specifications for installations inside buildings conveying water for human consumption - Part 5: Operation and maintenance
- SS-EN-89 - Gas-fired storage water heaters for the production of domestic hot water
- SS-EN-89-AM1 - Gas-fired storage water heaters for the production of domestic hot water
- SS-EN-89-AM2 - Gas fired storage water heaters for the production of domestic hot water
- SS-EN-89-AM3 - Gas-fired storage water heaters for the production of domestic hot water
- SS-EN-ISO-11177 - Vitreous and porcelain enamels - Inside and outside enamelled valves and pressure pipe fittings for untreated and potable water supply - Quality requirements and testing (ISO 11177:2019)
- SS-EN-ISO-13056 - Plastics piping systems - Pressure systems for hot and cold water - Test method for leaktightness under vacuum (ISO 13056:2011)
- SS-EN-ISO-13844 - Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with plastic pressure pipes - Test method for leak tightness under negative pressure, angular deflection and deformation (ISO 13844:2022)
- SS-EN-ISO-13845 - Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with thermoplastic pressure pipes - Test method for leaktightness under internal pressure and with angular deflection (ISO 13845:2015)
- SS-EN-ISO-1452-1 - Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: General (ISO 1452-1:2009)
- SS-EN-ISO-1452-2 - Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Pipes (ISO 1452-2:2009)
- SS-EN-ISO-1452-3 - Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Fittings (ISO 1452-3:2009, corrected version 2010-03-01)
- SS-EN-ISO-1452-4 - Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves (ISO 1452-4:2009)
- SS-EN-ISO-1452-5 - Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 5: Fitness for purpose of the system (ISO 1452-5:2009, corrected version 2010-03-01)
- SS-EN-ISO-15874-1 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General (ISO 15874-1:2013)
- SS-EN-ISO-15874-1-AM1 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General - Amendment 1: Impact test (ISO 15874-1:2013/Amd 1:2022)
- SS-EN-ISO-15874-2 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes (ISO 15874-2:2013)
- SS-EN-ISO-15874-2-AM1 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes - Amendement 2: Impact test (ISO 15874-2:2013/Amd 2:2022)
- SS-EN-ISO-15874-3 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings (ISO 15874-3:2013)
- SS-EN-ISO-15874-3-AM2 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings - Amendment 2 (ISO 15874-3:2013/Amd 2:2021)
- SS-EN-ISO-15874-5 - Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 5: Fitness for purpose of the system (ISO 15874-5:2013)
- SS-EN-ISO-15875-1 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 1: General (ISO 15875-1:2003)
- SS-EN-ISO-15875-1-AM1 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 1: General - Amendment 1 (ISO 15875-1:2003/Amd 1:2007)
- SS-EN-ISO-15875-2 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 2: Pipes
- SS-EN-ISO-15875-2-AM1 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 2: Pipes - Amendment 1 (ISO 15875-2:2003/Amd 1:2007)
- SS-EN-ISO-15875-2-AM2 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 2: Pipes - Amendment 2 (ISO 15875-2:2003/Amd 2:2020)
- SS-EN-ISO-15875-3 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings (ISO 15875-3:2003)
- SS-EN-ISO-15875-3-AM1 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings - Amendment 1 (ISO 15875-3:2003/Amd 1:2020)
- SS-EN-ISO-15875-3-AM2 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings - Amendment 2 (ISO 15875-3:2003/Amd 2:2021)
- SS-EN-ISO-15875-5 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 5: Fitness for purpose of the system (ISO 15875-5:2003)
- SS-EN-ISO-15875-5-AM1 - Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 5: Fitness for purpose of the system - Amendment 1 (ISO 15875-5:2003/Amd 1:2020)
- SS-EN-ISO-15876-1 - Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 1: General (ISO 15876-1:2003)
- SS-EN-ISO-15876-1-AM1 - Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 1: General - Amendment 1 (ISO 15876-1:2003/Amd 1:2007)
- SS-EN-ISO-15876-2 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 2: Pipes (ISO 15876-2:2017)
- SS-EN-ISO-15876-2-AM1 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 2: Pipes - Amendment 1 (ISO 15876-2:2017/Amd 1:2020)
- SS-EN-ISO-15876-3 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 3: Fittings (ISO 15876-3:2017)
- SS-EN-ISO-15876-3-AM1 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 3: Fittings - Amendment 1 (ISO 15876-3:2017/Amd 1:2020)
- SS-EN-ISO-15876-3-AM2 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 3: Fittings - Amendment 2 (ISO 15876-3:2017/Amd 2:2021)
- SS-EN-ISO-15876-5 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system (ISO 15876-5:2017)
- SS-EN-ISO-15876-5-AM1 - Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system - Amendment 1 (ISO 15876-5:2017/Amd 1:2020)
- SS-EN-ISO-15877-1 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: General (ISO 15877-1:12009)
- SS-EN-ISO-15877-1-AM1 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: General - Amendment 1 (ISO 15877-1:2009/Amd 1:2010)
- SS-EN-ISO-15877-2 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Pipes (ISO 15877-2:2009)
- SS-EN-ISO-15877-2-AM1 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Pipes - Amendment 1 (ISO 15877-2:2009/Amd 1:2010)
- SS-EN-ISO-15877-2-AM2 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Pipes - Amendment 2 (ISO 15877-2:2009/Amd 2:2020)
- SS-EN-ISO-15877-3 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings (ISO 15877-3:2009)
- SS-EN-ISO-15877-3-AM1 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings - Amendment 1 (ISO 15877-3:2009/Amd 1:2010)
- SS-EN-ISO-15877-3-AM2 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings - Amendment 2 (ISO 15877-3:2009/Amd 2:2021)
- SS-EN-ISO-15877-5 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system (ISO 15877-5:2009)
- SS-EN-ISO-15877-5-AM1 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system - Amendment 1 (ISO 15877-5:2009/Amd 1:2010)
- SS-EN-ISO-15877-5-AM2 - Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system - Amendment 2 (ISO 15877-5:2009/Amd 2:2020)
- SS-EN-ISO-21003-1 - Multilayer piping systems for hot and cold water installations inside buildings - Part 1: General (ISO 21003-1:2008)
- SS-EN-ISO-21003-2 - Multilayer piping systems for hot and cold water installations inside buildings - Part 2: Pipes (ISO 21003-2:2008)
- SS-EN-ISO-21003-2-AM1 - Multilayer piping systems for hot and cold water installations inside buildings - Part 2: Pipes - Amendment 1 (ISO 21003-2:2008/Amd 1:2011)
- SS-EN-ISO-21003-3 - Multilayer piping systems for hot and cold water installations inside buildings - Part 3: Fittings (ISO 21003-3:2008)
- SS-EN-ISO-21003-3-AM1 - Multilayer piping systems for hot and cold water installations inside buildings - Part 3: Fittings - Amendment 1 (ISO 21003-3:2008/Amd 1:2021)
- SS-EN-ISO-21003-5 - Multilayer piping systems for hot and cold water installations inside buildings - Part 5: Fitness for purpose of the system (ISO 21003-5:2008)
- SS-EN-ISO-22391-1 - Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 1: General (ISO 22391-1:2009)
- SS-EN-ISO-22391-2 - Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 2: Pipes (ISO 22391-2:2009)
- SS-EN-ISO-22391-2-AM1 - Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 2: Pipes - Amendment 1 (ISO 22391-2:2009/Amd 1:2020)
- SS-EN-ISO-22391-3 - Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 3: Fittings (ISO 22391-3:2009)
- SS-EN-ISO-22391-3-AM 1 - Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 3: Fittings - Amendment 1 (ISO 22391-3:2009/Amd 1:2020)
- SS-EN-ISO-22391-3-AM2 - Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 3: Fittings - Amendment 2 (ISO 22391-3:2009/Amd 2:2021)
- SS-EN-ISO-22391-5 - Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 5: Fitness for purpose of the system (ISO 22391-5:2009)
- SS-EN-ISO-22391-5-AM1 - Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 5: Fitness for purpose of the system - Amendment 1 (ISO 22391-5:2009/Amd 1:2020)
- SS-EN-ISO-3822-1 - Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 1: Method of measurement (ISO 3822-1:1999)
- SS-EN-ISO-3822-1-AM1 - Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 1: Method of measurement - Amendment 1: Measurement uncertainty (ISO 3822-1:1999/Amd 1:2008)
- SS-EN-ISO-3822-2 - Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 2: Mounting and operating conditions for draw-off taps and mixing valves (ISO 3822-2:1995)
- SS-EN-ISO-3822-3 - Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 3: Mounting and operating conditions for in-line valves and appliances (ISO 3822-3:2018)
- SS-EN-ISO-3822-3-AM1 - Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 3: Mounting and operating conditions for in-line valves and appliances - Amendment 1 (ISO 3822-3:1997/Amd 1:2009)
- SS-EN-ISO-4064-1 - Water meters for cold potable water and hot water - Part 1: Metrological and technical requirements (ISO 4064-1:2014)
- SS-EN-ISO-4064-1-AM11 - Water meters for cold potable water and hot water - Part 1: Metrological and technical requirements (ISO 4064-1:2014)
- SS-EN-ISO-4064-2 - Water meters for cold potable water and hot water - Part 2: Test methods (ISO 4064-2:2014)
- SS-EN-ISO-4064-2-AM11 - Water meters for cold potable water and hot water - Part 2: Test methods (ISO 4064-2:2014)
- SS-EN-ISO-4064-3 - Water meters for cold potable water and hot water - Part 3: Test report format (ISO 4064-3:2014)
- SS-EN-ISO-4064-4 - Water meters for cold potable water and hot water - Part 4: Non-metrological requirements not covered in ISO 4064-1 (ISO 4064-4:2014)
- SS-EN-ISO-4064-5 - Water meters for cold potable water and hot water - Part 5: Installation requirements (ISO 4064-5:2014)
- SS-EN-ISO-4064-5-AM11 - Water meters for cold potable water and hot water - Part 5: Installation requirements (ISO 4064-5:2014)
- SS-EN-ISO-8795 - Plastic piping systems for the transport of water intended for human consumption - Migration assessment - Determination of migration values of plastics pipes and fittings and their joints (ISO 8795:2001)
- SS-ENV-12108 - Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption
- SS-ENV-1452-6 - Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 6: Guidance for installation
- SS-ISO-10508 - Plastics piping systems for hot and cold water installations - Guidance for classification and design (ISO 10508:2006, IDT)
- SS-ISO-10508-AM1 - Plastics piping systems for hot and cold water installations - Guidance for classification and design - Amendment 1 (ISO 10508:2006/Amd 1:2018, IDT)
- SS-ISO-10639 - Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin (ISO 10639:2004, IDT)
- SS-ISO-10639-AM1 - Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin - Amendment 1 (ISO 10639:2004/Amd 1:2011, IDT)
- SS-ISO-14236 - Plastics pipes and fittings - Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems
- SS-ISO-16422 - Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure - Specifications (ISO 16422:2006, IDT)
- SS-ISO-23711 - Elastomeric seals - Requirements for materials for pipe joint seals used in water and drainage applications - Thermoplastic elastomers (ISO 23711:2022, IDT)
- SS-ISO-25780 - Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin - Pipes with flexible joints intended to be installed using jacking techniques (ISO 25780:2011, IDT)
- SS-ISO-4064-2 - Thermal insulation products for buildings - In-situ formed loose-fill mineral wool (MW) products - Part 1: Specification for the loose-fill products before installation
- SS-ISO-4427-1 - Plastics piping systems for water supply and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General (ISO 4427-1:2019, IDT)
- SS-ISO-4427-2 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes (ISO 4427-2:2019, IDT)
- SS-ISO-4427-2-AM1 - Plastics piping systems - Polyethylene (PE) pipes and fittings for water supply - Part 2: Pipes - Amendment 1 (ISO 4427-2:2007/Amd 1:2014, IDT)
- SS-ISO-4427-3 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings (ISO 4427-3:2019, IDT)
- SS-ISO-4427-5 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system (ISO 4427-5:2019, IDT)
- SS-ISO-4633 - Rubber seals - Joint rings for water supply, drainage and sewerage pipelines - Specification for materials (ISO 4633:2015, IDT)
- UNI-EN-13443-1-PDF - Part 1: Particle Rating 80 Um To 150 Um - Requirements for Performances, Safety & Test
- UNI-EN-13443-2 - Part 2: Particle Rating 1 Um To Less Than 80 Um - Requirements for Performance, Safety