Document Center List of Standards on Building Accessories Including Locks, Buzzers, Bells, Bolts, Door And Window Hardware, Etc.
ICS Code 91.190
Return to ICS Index.Up to Level 1:
The following documents are a part of this series:
ASTM:
- ASTM-A153 - Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware
- ASTM-A750 - Standard Specification for Steel Air Ventilating Grille Units for Detention Areas (Withdrawn 2004)
- ASTM-D7147 - Standard Specification for Testing and Establishing Allowable Loads of Joist Hangers
- ASTM-F1577 - Standard Test Methods for Detention Locks for Swinging Doors
- ASTM-F1643 - Standard Test Methods for Detention Sliding Door Locking Device Assembly
- ASTM-F2348 - Standard Performance Specification for Privacy Padlocks
- ASTM-F471 - Standard Terminology Relating to Combination Locks
- ASTM-F883 - Standard Performance Specification for Padlocks
BSI:
- BS-10621 - Lock assemblies in which the operating mode can be switched between the normal BS 8621 operating mode and a secure mode in which no egress is possible
- BS-10621-TC - Tracked Changes. Lock assemblies in which the operating mode can be switched between the normal BS 8621 operating mode and a secure mode in which no egress is possible
- BS-2911 - Specification for letter plates
- BS-3621 - Lock assemblies operated by key from both the inside and outside of the door
- BS-3621-TC - Tracked Changes. Lock assemblies operated by key from both the inside and outside of the door
- BS-4951 - Specification for builders' hardware: lock and latch furniture (doors)
- BS-6100-6 - Building and civil engineering. Vocabulary
- BS-6459-1 - Door Closers, Specification for Mechanical Performance of Crank & Rack & Pinion Overhe
- BS-8424 - Building hardware. Pull handles. Requirements and test methods
- BS-8607 - Mechanically operated push button locksets. Requirements and test methods
- BS-8621 - Lock assemblies operated by key from the outside of the door and by handle or thumb turn from the inside of the door
- BS-8621-TC - Tracked Changes. Lock assemblies operated by key from the outside of the door and by handle or thumb turn from the inside of the door
- BS-EN-1125 - Building hardware. Panic exit devices operated by a horizontal bar, for use on escape routes. Requirements and test methods
- BS-EN-1154 - Building hardware. Controlled door closing devices. Requirements and test methods
- BS-EN-1155 - Building hardware. Electrically powered hold-open devices for swing doors. Requirements and test methods
- BS-EN-1158 - Building hardware. Door coordinator devices. Requirements and test methods
- BS-EN-12051 - Building hardware. Door and window bolts. Requirements and test methods
- BS-EN-12209 - Building hardware. Mechanically operated locks and locking plates. Requirements and test methods
- BS-EN-12209-TC - Tracked Changes. Building hardware. Mechanically operated locks and locking plates. Requirements and test methods
- BS-EN-12320 - Building hardware. Padlocks and padlock fittings. Requirements and test methods
- BS-EN-12320-TC - Tracked Changes. Building hardware. Padlocks and padlock fittings. Requirements and test methods
- BS-EN-1303 - Building hardware. Cylinders for locks. Requirements and test methods
- BS-EN-13126-1 - Building hardware. Hardware for windows and door height windows. Requirements and test methods
- BS-EN-13126-10 - Building hardware. Requirements and test methods for windows and doors height windows
- BS-EN-13126-11 - Building hardware. Requirements and test methods for windows and doors height windows
- BS-EN-13126-12 - Building hardware. Requirements and test methods for windows and doors height windows
- BS-EN-13126-13 - Building hardware. Hardware for windows and door height windows. Requirements and test methods
- BS-EN-13126-13-TC - Tracked Changes. Building hardware. Hardware for windows and door height windows. Requirements and test methods
- BS-EN-13126-14 - Building hardware. Hardware for windows and door height windows. Requirements and test methods
- BS-EN-13126-14-TC - Tracked Changes. Building hardware. Hardware for windows and door height windows. Requirements and test methods
- BS-EN-13126-15 - Building hardware. Hardware for windows and door height windows. Requirements and test methods
- BS-EN-13126-16 - Building hardware. Hardware for windows and door height windows. Requirements and test methods
- BS-EN-13126-17 - Building hardware. Hardware for windows and door height windows. Requirements and test methods
- BS-EN-13126-1-TC - Tracked Changes. Building hardware. Hardware for windows and door height windows. Requirements and test methods
- BS-EN-13126-2 - Building hardware. Hardware for windows and door height windows. Requirements and test methods
- BS-EN-13126-3 - Building hardware. Hardware for windows and door - height windows. Requirements and test methods
- BS-EN-13126-3-TC - Tracked Changes. Building hardware. Hardware for windows and door - height windows. Requirements and test methods
- BS-EN-13126-4 - Building hardware. Hardware for windows and door height windows. Requirements and test methods
- BS-EN-13126-4-TC - Tracked Changes. Building hardware. Hardware for windows and door height windows. Requirements and test methods
- BS-EN-13126-5 - Building hardware. Hardware for windows and door height windows. Requirements and test methods
- BS-EN-13126-6 - Building hardware. Hardware for windows and door height windows. Requirements and test methods
- BS-EN-13126-6-TC - Tracked Changes. Building hardware. Hardware for windows and door height windows. Requirements and test methods
- BS-EN-13126-7 - Building hardware. Hardware for windows and door height windows. Requirements and test methods
- BS-EN-13126-8 - Building hardware. Hardware for windows and door height windows
- BS-EN-13126-8-TC - Tracked Changes. Building hardware. Hardware for windows and door height windows
- BS-EN-13126-9 - Building hardware. Requirements and test methods for windows and door height windows
- BS-EN-13637 - Building hardware. Electrically controlled exit systems for use on escape routes. Requirements and test methods
- BS-EN-14637 - Building hardware. Electrically controlled hold-open systems for fire/smoke door assemblies. Requirements, test methods, application and maintenance
- BS-EN-14648 - Building hardware. Fittings for shutters. Requirements and test methods
- BS-EN-1527 - Building hardware. Hardware for sliding doors and folding doors. Requirements and test methods
- BS-EN-15570 - Hardware for furniture. Strength and durability of hinges and their components. Hinges pivoting on a vertical axis
- BS-EN-15684 - Building hardware. Mechatronic cylinders. Requirements and test methods
- BS-EN-16035 - Hardware performance sheet (HPS). Identification and summary of test evidence to facilitate the inter-changeability of building hardware for application to fire resisting and/or smoke control doorsets and/or openable windows
- BS-EN-16035-TC - Tracked Changes. Hardware performance sheet (HPS). Identification and summary of test evidence to facilitate the inter-changeability of building hardware for application to fire resisting and/or smoke control doorsets and/or openable windows
- BS-EN-1670 - Building hardware. Corrosion resistance. Requirements and test methods
- BS-EN-16864 - Building hardware. Mechatronic padlocks. Requirements and test methods
- BS-EN-16867 - Building hardware. Mechatronic door furniture. Requirements and test methods
- BS-EN-17610 - Building hardware. Environmental product declarations. Product category rules complementary to EN 15804 for building hardware
- BS-EN-179 - Building hardware. Emergency exit devices operated by a lever handle or push pad, for use on escape routes. Requirements and test methods
- BS-EN-1906 - Building hardware. Lever handles and knob furniture. Requirements and test methods
- DD-8455 - Materials for gaskets and weatherstripping for windows, doors, conservatories and curtain walling. Requirements and test methods
- DD-CEN-13126-1 - Building Hardware, Fittings for Windows & Door Height Windows, Requirements & Test Met
- DD-CEN-13126-10 - Building hardware, fittings for windows and door height windows. Requirements and test methods
- DD-CEN-13126-11 - Building Hardware, Fittings for Windows & Door Height Windows, Requirements & Test Met
- DD-CEN-13126-12 - Building Hardware, Fittings for Windows & Door Height Windows, Requirements & Test Met
- DD-CEN-13126-13 - Building hardware, fittings for windows and door height windows. Requirements and test methods. Sash balances
- DD-CEN-13126-14 - Building hardware, fittings for windows and door height windows. Requirements and test methods. Sash fasteners
- DD-CEN-13126-15 - Building Hardware, Fittings for Windows & Door Height Windows, Requirements & Test Met
- DD-CEN-13126-16 - Building Hardware, Fittings for Windows & Door Height Windows, Requirements & Test Met
- DD-CEN-13126-17 - Building Hardware, Fittings for Windows & Door Height Windows, Requirements & Test Met
- DD-CEN-13126-2 - Building Hardware, Fittings for Windows & Door Height Windows, Requirements & Test Met
- DD-CEN-13126-3 - Building Hardware, Fittings for Windows & Door Height Windows, Requirements & Test Met
- DD-CEN-13126-4 - Building hardware, fittings for windows and door height windows. Requirements and test methods
- DD-CEN-13126-5 - Building hardware, fittings for windows and door height windows. Requirements and test methods. Devices that restrict the opening of windows
- DD-CEN-13126-6 - Building Hardware, Fittings for Windows & Door Height Windows, Requirements & Test Met
- DD-CEN-13126-7 - Building Hardware, Fittings for Windows & Door Height Windows, Requirements & Test Met
- DD-CEN-13126-8 - Building Hardware, Fittings for Windows and Door Height Windows, Requirements and Test Met
- DD-CEN-13126-9 - Building hardware, fittings for windows and door height windows. Requirements and test methods. Pivot hinges
- DD-ENV-1300 - Secure Storage Units, Classification for High Security Locksaccording To Their Resista
- PD-CEN-15894 - Building hardware. Door fittings for use by children, elderly and disabled people in domestic and public buildings. A guide for specifiers
- PD-CEN-17814 - Building hardware. Master Key System data protection. Guidance
Other SDOs:
- DIN-18650-1 - Part 1: Product Requirements and Test Methods, Powered Pedestrian Doors
- DIN-18650-2 - Part 2: Safety at Powered Pedestrian Doors, Powered Pedestrian Doors
- DIN-EN-12209 - Building hardware - Mechanically operated locks and locking plates - Requirements and test methods; German version EN 12209:2016
- DIN-EN-1303 - Building hardware - Cylinders for locks - Requirements and test methods; German version EN 1303:2015
- DIN-EN-13126-1 - Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 1: Requirements common to all types of hardware
- DIN-EN-13126-8 - Building hardware - Requirements and test methods for windows and doors height windows - Part 8: Tilt and Turn, Tilt-First and Turn-Only hardware; German version EN 13126-8:2006
- DIN-EN-1670 - Building Hardware - Corrosion Resistance - Requirements & Test Methods
- DIN-EN-1906 - Building hardware - Lever handles and knob furniture - Requirements and test methods; German version EN 1906:2012
- DS-EN-1906 - Building hardware - Lever handles and knob furniture - Requirements and test methods
- EN-1125 - Building Hardware - Panic Exit Devices Operated by a Horizontal Bar, for Use on Escape
- EN-1154 - Building Hardware, Controlled Door Closing Devices, Requirements & Test Methods
- EN-12209 - Building hardware - Mechanically operated locks and locking plates - Requirements and test methods
- EN-12320 - Building hardware - Padlocks and padlock fittings - Requirements and test methods
- EN-1303 - Building hardware - Cylinders for locks - Requirements and test methods
- EN-13126-1 - Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 1: Requirements common to all types of hardware
- EN-13126-10 - Part 10: Arm-Balancing Systems, Building Hardware - Requirements & Test Methods for Wi
- EN-13126-12 - Part 12: Side Hung Projecting Reversible Hardware, Building Hardware - Requirements &
- EN-13126-13 - Building hardware - Hardware for windows and balcony doors - Requirements and test methods - Part 13: Sash balances
- EN-13126-14 - Building hardware - Hardware for windows and balcony doors - Requirements and test methods - Part 14: Sash fasteners
- EN-13126-15 - Part 15: Rollers for Horizontal Sliding & Sliding Folding Windows & Doors; Building Ha
- EN-13126-16 - Part 16: Hardware for Lift & Slide Windows & Doors; Building Hardware - Requirements &
- EN-13126-17 - Part 17: Hardware for Tilt & Slide Windows & Doors, Building Hardware - Requirements &
- EN-13126-2 - Building hardware - Requirements and test methods for windows and doors height windows - Part 2: Window fastener handles
- EN-13126-3 - Building hardware - Hardware for windows and door-height windows - Requirements and test methods - Part 3: Handles, primarily for Tilt&Turn, Tilt-First and Turn-Only hardware
- EN-13126-5 - Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 5: Devices that restrict the opening of windows and door height windows
- EN-13126-7 - Building Hardware, Requirements & Test Methods for Windows & Door Height Windows, Fing
- EN-13126-8 - Building hardware - Hardware for windows and door height windows - Part 8: Requirements and test methods for Tilt and Turn, Tilt-First and Turn-Only hardware
- EN-13126-9 - Building hardware - Requirements and test methods for windows and door height windows - Part 9: Hardware for horizontal and vertical pivot windows
- EN-13637 - Building hardware - Electrically controlled exit systems for use on escape routes - Requirements and test methods
- EN-14637 - Building Hardware, Electrically Controlled Hold-Open Systems for Fire/Smoke Door Assem
- EN-14648 - Building Hardware - Fittings for Shutters - Requirements & Test Methods
- EN-1527 - Building hardware - Hardware for sliding doors and folding doors - Requirements and test methods
- EN-15570 - Hardware for Furniture, Strength & Durability of Hinges & Their Components, Hinges Piv
- EN-15684 - Building hardware - Mechatronic cylinders - Requirements and test methods
- EN-16035 - Hardware performance sheet (HPS) - Identification and summary of test evidence to facilitate the inter-changeability of building hardware for application to fire resisting and/or smoke control doorsets and/or openable windows
- EN-1670 - Building Hardware - Corrosion Resistance - Requirements & Test Methods
- EN-16864 - Building hardware - Mechatronic padlocks - Requirements and test methods
- EN-179 - Building Hardware - Emergency Exit Devices Operated by a Lever Handle or Push Pad, For
- EN-1906 - Building hardware - Lever handles and knob furniture - Requirements and test methods
- SIS-CEN/TR-15894 - Building hardware - Door fittings for use by children, elderly and disabled people in domestic and public buildings - A guide for specifiers
- SIS-CEN/TS-17814 - Building hardware - Master Key System data protection - Guidance
- SMS-3043 - Demountable bodies - Requirements and testing
- SMS-3063 - Plaströr - Dräneringsrör och rördelar
- SMS-3064 - Plaströr - Dräneringsrör och rördelar - Provning och kontroll
- SMS-3078 - Door and window fittings. Fixed mounted locks. Testing
- SMS-3079 - Door and window fittings. Fixed mounted locks. Burglar resistant locks. Requirements
- SMS-3080 - Door and window fittings. Striking plates for burglar resistant locks
- SMS-3094 - Wheeled tractors - Determination of maximum travel speed
- SMS-9001 - Brandmateriel - Översikt
- SMS-9008 - Pins and non-threaded bolts. List of standards
- SS-EN-1125 - Building hardware - Panic exit devices operated by a horizontal bar, for use on escape routes - Requirements and test methods
- SS-EN-1125-AM1 - Building hardware - Panic exit devices operated by a horizontal bar - Requirements and test methods
- SS-EN-1154 - Building hardware - Controlled door closing devices - Requirements and test methods
- SS-EN-1154-AM1 - Building hardware - Controlled door closing devices - Requirements and test methods
- SS-EN-1155 - Building hardware - Electrically powered hold-open devices for swing doors - Requirements and test methods
- SS-EN-1155-AM1 - Building hardware - Electrically powered hold-open devices for swing doors - Requirements and test methods
- SS-EN-1158 - Building hardware - Door coordinator devices - Requirements and test methods
- SS-EN-1158-AM1 - Building hardware - Door coordinator devices - Requirements and test methods
- SS-EN-12046-1 - Operating forces - Test method - Part 1: Windows
- SS-EN-12051 - Building hardware - Door and window bolts - Requirements and test methods
- SS-EN-12209 - Building hardware - Mechanically operated locks and locking plates - Requirements and test methods
- SS-EN-12320 - Building hardware - Padlocks and padlock fittings - Requirements and test methods
- SS-EN-12365-1 - Building hardware - Gasket and weatherstripping for doors, windows, shutters and curtain walling - Part 1: Performance requirements and classification
- SS-EN-12365-2 - Building hardware - Gasket and weatherstripping for doors, windows, shutters and curtain walling - Part 2: Linear compression force test methods
- SS-EN-12365-3 - Building hardware - Gasket and weatherstripping for doors, windows, shutters and curtain walling - Part 3: Deflection recovery test method
- SS-EN-12365-4 - Building hardware - Gasket and weatherstripping for doors, windows, shutters and curtain walling - Part 4: Recovery after accelerated ageing test method
- SS-EN-12868 - Child use and care articles - Method for determining the release of N-nitrosamines and N-nitrosatable substances from elastomer or rubber teats and soothers
- SS-EN-1300 - Secure storage units - Classification for high security locks according to their resistance to unauthorized opening
- SS-EN-13126-1 - Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 1: Requirements common to all types of hardware
- SS-EN-13126-10 - Building hardware - Requirements and test methods for windows and doors height windows - Part 10: Arm-balancing systems
- SS-EN-13126-11 - Building hardware - Requirements and test methods for windows and doors height windows - Part 11: Top hung projecting reversible hardware
- SS-EN-13126-12 - Building hardware - Requirements and test methods for windows and doors height windows - Part 12: Side hung projecting reversible hardware
- SS-EN-13126-13 - Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 13: Sash balances
- SS-EN-13126-14 - Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 14: Sash fasteners
- SS-EN-13126-15 - Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 15: Rollers for horizontal sliding and hardware for sliding folding windows
- SS-EN-13126-16 - Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 16: Hardware for Lift and Slide windows
- SS-EN-13126-17 - Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 17: Hardware for Tilt and Slide windows
- SS-EN-13126-19 - Building hardware - Requirements and test methods for windows and door height windows - Part 19: Sliding Closing Devices
- SS-EN-13126-2 - Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 2: Window fastener handles
- SS-EN-13126-3 - Building hardware - Hardware for windows and door-height windows - Requirements and test methods - Part 3: Handles, primarily for Tilt&Turn, Tilt-First and Turn-Only hardware
- SS-EN-13126-4 - Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 4: Espagnolettes
- SS-EN-13126-5 - Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 5: Devices that restrict the opening of windows and door height windows
- SS-EN-13126-6 - Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 6: Variable geometry stay hinges (with or without a friction stay)
- SS-EN-13126-7 - Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 7: Finger catches
- SS-EN-13126-8 - Building hardware - Hardware for windows and door height windows - Part 8: Requirements and test methods for Tilt and Turn, Tilt-First and Turn-Only hardware
- SS-EN-13126-9 - Building hardware - Requirements and test methods for windows and door height windows - Part 9: Hardware for horizontal and vertical pivot windows
- SS-EN-13637 - Building hardware - Electrically controlled exit systems for use on escape routes - Requirements and test methods
- SS-EN-14637 - Building hardware - Electrically controlled hold-open systems for fire/smoke door assemblies - Requirements, test methods, application and maintenance
- SS-EN-14648 - Building hardware - Fittings for shutters - Requirements and test methods
- SS-EN-14765 - Bicycles for young children - Safety requirements and test methods
- SS-EN-14846 - Building hardware - Locks and latches - Electromechanically operated locks and striking plates - Requirements and test methods
- SS-EN-1527 - Building hardware - Hardware for sliding doors and folding doors - Requirements and test methods
- SS-EN-15570 - Hardware for furniture - Strength and durability of hinges and their components - Hinges pivoting on a vertical axis
- SS-EN-15684 - Building hardware - Mechatronic cylinders - Requirements and test methods
- SS-EN-16005 - Power operated pedestrian doorsets - Safety in use - Requirements and test methods
- SS-EN-16035 - Hardware performance sheet (HPS) - Identification and summary of test evidence to facilitate the inter-changeability of building hardware for application to fire resisting and/or smoke control doorsets and/or openable windows
- SS-EN-16139 - Furniture - Strength, durability and safety - Requirements for non-domestic seating
- SS-EN-1670 - Building hardware - Corrosion resistance - Requirements and test methods
- SS-EN-16729-2 - Railway applications - Infrastructure - Non-destructive testing on rails in track - Part 2: Eddy current testing of rails in track
- SS-EN-16864 - Building hardware - Mechatronic padlocks - Requirements and test methods
- SS-EN-17610 - Building hardware - Environmental product declarations - Product category rules complementary to EN 15804 for building hardware
- SS-EN-179 - Building hardware - Emergency exit devices operated by a lever handle or push pad, for use on escape routes - Requirements and test methods
- SS-EN-179-AM1 - Building hardware - Emergency exit devices operated by a lever handle or push pad - Requirements and test methods
- SS-EN-1906 - Building hardware - Lever handles and knob furniture - Requirements and test methods
- SS-EN-1935 - Building hardware - Single-axis hinges - Requirements and test methods
- SS-EN-1996-1-1 - Eurocode 6: Design of masonry structures - Part 1-1: General rules for reinforced and unreinforced masonry structures
- SS-EN-ISO-11981 - Ophthalmic optics - Contact lenses and contact lens care products -Determination of physical compatibility of contact lens care products with contact lenses (ISO 11981:2017)
- SS-ISO-10303-21 - Industrial automation systems and integration - Product data representation and exchange - Part 21: Implementation methods: Clear text encoding of the exchange structure (ISO 10303-21:2016, IDT)
- SS-ISO-10303-24 - Industrial automation systems and integration - Product data representation and exchange - Part 24: Implementation methods: C language binding of standard data access interface
- SS-ISO-13226 - Rubber - Standard reference elastomers (SREs) for characterizing the effect of liquids on vulcanized rubbers (ISO 13226:2018, IDT)
- SS-ISO-2125 - SAKNAS
- SS-ISO-2149 - SAKNAS
- SS-ISO-2150 - SAKNAS
- SS-ISO-2196 - SAKNAS
- SS-ISO-2381 - SAKNAS
- SS-ISO-2390 - SAKNAS
- SS-ISO-2392 - SAKNAS
- SS-ISO-3264 - SAKNAS
- SS-ISO-3276 - SAKNAS
- SS-ISO-3277 - SAKNAS
- SS-ISO-3278 - SAKNAS
- SS-ISO-3279 - SAKNAS
- SS-ISO-3280 - SAKNAS
- SS-ISO-3281 - SAKNAS
- SS-ISO-3283 - SAKNAS
- SS-ISO-5028 - SAKNAS
- SS-ISO-5030 - SAKNAS
- SS-ISO-5036 - SAKNAS
- SS-ISO-5062 - Atomizing oil burners of the monobloc type - Dimensions for pumps