ASTM-A250 › Standard Specification for Electric-Resistance-Welded Ferritic Alloy-Steel Boiler and Superheater Tubes (Withdrawn 2017)
The following bibliographic material is provided to assist you with your purchasing decision:
This guide covers standard specification for several grades, designated T1, T1a, T1b, T2, T11, T12, and T22, of minimum-wall-thickness, electric-resistance-welded, carbon-molybdenum and chromium-molybdenum alloy-steel, boiler and superheater tubes. Product analysis shall be done wherein the material shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, molybdenum, and chromium. The material shall conform to the required tensile properties, namely: tensile strength, yield strength, and elongation. The computed minimum elongation values for steel with decreasing wall thickness shall be given. The tubes shall have a hardness not exceeding the specified values for Brinell hardness and Rockwell hardness numbers. When the final heat treatment is in a continuous furnace, the number of tubes of the same size and from the same heat in a lot shall be determined from the given size of the tubes. Required mechanical tests such as tensile test, flattening test, flange test, reverse flattening test, hardness test, and hydrostatic or nondestructive electric tests, shall be performed on the steel specimen.
Scope
1.1 This specification2 covers several grades, designated T1, T1a, T1b, T2, T11, T12 and T22, of minimum-wall-thickness, electric-resistance-welded, carbon-molybdenum and chromium-molybdenum alloy-steel, boiler and superheater tubes.
1.2 The tubing sizes and thicknesses usually furnished to this specification are 1/2 to 5 in. [12.7 to 127 mm] in outside diameter and 0.035 to 0.320 in. [0.9 to 8.1 mm], inclusive, in minimum wall thickness. Tubing having other dimensions may be furnished, provided such tubes comply with all other requirements of this specification.
1.3 Mechanical property requirements do not apply to tubing smaller than 1/8 in. [3.2 mm] in inside diameter or 0.015 in. [0.4 mm] in thickness.
1.4 An optional supplementary requirement is provided for non-destructive examination for certain ASME applications.
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5.1 Within the text, the SI units are shown in brackets.
1.5.2 The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
Keywords
boiler tube; resistance welded steel tube; steel tube, alloy; superheater tube; welded steel tube; ICS Number Code 23.040.10 (Iron and steel pipes)
To find similar documents by ASTM Volume:
01.01 (Steel--Piping, Tubing, Fittings)
To find similar documents by classification:
23.040.10 (Iron and steel pipes Steel pipes and tubes for specific use, see 77.140.75)
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Customers who bought this document also bought:
ASTM-A240Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
IPC/EIA-J-STD-001
Requirements for Soldered Electrical and Electronic Assemblies
IPC-A-610
Acceptability of Electronic Assemblies (Hardcopy format)
Document Number
ASTM-A250/A250M-05(2014)
Revision Level
2005 R14 EDITION
Status
Cancelled
Modification Type
Withdrawn
Publication Date
Oct. 15, 2014
Document Type
Specification
Page Count
4 pages
Committee Number
A01.10