ASTM-A861 › Standard Specification for High-Silicon Iron Pipe and Fittings
The following bibliographic material is provided to assist you with your purchasing decision:
Scope
1.1 This specification covers high-silicon iron pipe and pipe fittings intended for corrosion-resistant service for both above- and below-grade construction.
1.2 Pipe and pipe fittings shall be the no-hub (MJ) or the hub and plain end design.
1.3 Pipe and pipe fittings shall be of the sizes specified in Table 1 and Figs. 1-71 or other sizes that may conform to the requirements given herein.
1.3.1 Pipe:
1.3.1.1 No-hub (MJ) (Fig. 1):Size (in.) | Length (ft) |
1½ | 7 |
2 | 7 |
3 | 7 |
4 | 7 |
1.3.1.2 Hub/Plain End (Fig. 35):
Size (in.) | Length (ft) |
2 | 7 |
3 | 7 |
4 | 7 |
6 | 7 |
8 | 7 |
10 | 5 |
12 | 5 |
15 | 5 |
1.3.2 Fitting (No-hub) (MJ):
Figs. | |
Quarter Bends | 2 |
Sixth Bends | 3 |
Return Bends | 4 |
Double-Branch Quarter Bend | 5 |
Eighth Bends | 6 |
Sixteenth Bends | 7 |
Long-Sweep Quarter Bends | 8 |
Sanitary Y Branches | 9 |
Double-Branch Sanitary Y | 10 |
Sanitary Combination Y and 1/8 Bend | 11 |
Double-Branch Sanitary Combination Y and 1/8 Bend | 12 |
Sanitary T Branches | 13 |
Double Branch Sanitary T | 14 |
Sanitary Running Traps | 15 |
Sanitary P Traps | 16 |
Swivel Trap P-Style Short | 17 |
Swivel Trap P-Style Long | 18 |
Swivel Trap S-Style Long | 19 |
Centrifugal Drum Trap P Swivel Type | 20 |
Centrifugal Drum Trap S Swivel Type | 21 |
Combination Cleanout and Test Tees | 22 |
Coupling | 23 |
Pipe Plugs | 24 |
Cleanout Plugs | 25 |
No-hub (MJ) Adapter | 26 |
Reducers-Increasers | 27 |
Sink Outlet | 28 |
Sink Overflows | 29 |
Threaded Adapters | 30 |
Trap Cleanout Details | 31 |
No-hub (MJ) Adapter | 32 |
(MJ) (No-hub) to Lead Adapter | 33 |
Floor Drains | 34 |
1.3.3 Fitting (Hub/Plain End):
Figs. | |
Hub Plain End Pipe | 35 |
Straight Tees | 36 |
Sanitary T Branches | 37 |
Sanitary Y Branches | 38 |
Double-Branch Sanitary Tee | 39 |
Double-Branch Sanitary Y | 40 |
Double-Branch Sanitary Combination Y and 1/8 Bend (T-Y) | 41 |
Short-Sweep Quarter Bends | 42 |
Long-Sweep Quarter Bends | 43 |
Sanitary Combination Y and 1/8 Bend (T-Y) | 44 |
Quarter Bends | 45 |
Sixth Bends | 46 |
Eighth Bends | 47 |
Sixteenth Bends | 48 |
Sanitary Increasers | 49 |
Hub Strainers | 50 |
Sanitary Reducers | 51 |
Double Hubs | 52 |
Pipe Plugs | 53 |
Cleanout Plugs | 54 |
Adapter-Plain end to Split Flange | 55 |
Adapter-Hub to-Split Flange | 56 |
Combination Cleanout and Test Tees | 57 |
Insertable Joints | 58 |
Backwater Valves | 59 |
Sanitary P Traps | 60 |
Sanitary S Traps | 61 |
Sanitary Running Traps | 62 |
Floor Drains | 63, 64, 65 |
Floor Drains | 66 |
Floor Drains/Installation-Funnel Attachment | 67, 68 |
Overflow | 69 |
Sink Outlet | 70 |
Detailed Cross Section of Cleanout | 71 |
Chemical Composition | Table 3 |
Transverse Bend Test Minimum Requirements | Table 4 |
Keywords
no-hub; corrosion resistant; fittings; high-silicon iron; hub/plain-end; hubless
To find similar documents by ASTM Volume:
01.02 (Ferrous Castings; Ferroalloys)
To find similar documents by classification:
23.040.10 (Iron and steel pipes Steel pipes and tubes for specific use, see 77.140.75)
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Customers who bought this document also bought:
BS-EN-809Pumps and pump units for liquids. Common safety requirements
UL-51
Standard for Power-Operated Pumps for Anhydrous Ammonia and LP-Gas
BS-EN-ISO-13857
Safety of machinery. Safety distances to prevent hazard zones being reached by upper and lower limbs
Document Number
ASTM-A0861-04R23
Revision Level
2004 R23 EDITION
Status
Current
Modification Type
Editorially changed
Publication Date
May 3, 2023
Document Type
Specification
Page Count
26 pages
Committee Number
A04.12