ASTM-B211M › Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold-Finished Bar, Rod, and Wire (Metric) (Withdrawn 2019)

ASTM-B211M - 2012(E1) EDITION - SUPERSEDED -- See the following: ASTM-B211
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:


This specification covers rolled or cold-finished aluminum and aluminum-alloy bar, rod, and wire and includes the following UNS alloy designations: A91060, A91100, A92011, A92014, A92017, A92024, A92219, A93003, A95052, A95056, A95154, A96061, A96110, A96262, and A97075. The temper conditions covered by this specification include: O, H14, H18, H12, H16, H112, F, T3, T4, T42, T451, T6, T62, T651, T36, T351, T851, H32, H34, H36, H38, H111, H192, H392, T 89, T94, T9, T73, and T7351. The products shall be produced either by hot extruding and cold finishing or by hot rolling with or without cold finishing. Bars, rods, and wires shall conform to the chemical composition requirements prescribed for aluminum, silicon, iron, copper, manganese, magnesium, chromium, zinc, bismuth, lead, and titanium, and to the specified tensile properties such as tensile strength, yield strength, and elongation. Requirements for quality assurance, heat treatment, chemical analysis, tension test, heat-treat response, bend testing, and stress-corrosion resistance and stress-corrosion cracking test are detailed.

ORDER

Want this as a site license?

Scope

1.1 This specification covers rolled or cold-finished bar, rod, and wire in alloys (Note 1) and tempers as shown in Table 2.

Note 1—Throughout this specification use of the term alloy in the general sense includes aluminum as well as aluminum alloy.

Note 2—The term cold finished is used to indicate the type of surface finish, sharpness of angles, and dimensional tolerances produced by drawing through a die.

Note 3—See Specification B221M for aluminum and aluminum-alloy extruded bars, rods, wire, shapes, and tubes; and Specification B316/B316M for aluminum and aluminum-alloy rivet and cold-heading wire and rods.

1.2 Alloy and temper designations are in accordance with ANSI H35.1M. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527.

1.3 This specification is the metric counterpart of Specification B211.

1.4 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.

Keywords

aluminum alloy; rolled or cold-finished bar; rolled or cold-finished rod; rolled or cold-finished wire; ICS Number Code 77.150.10 (Aluminium products)

To find similar documents by ASTM Volume:

02.02 (Aluminum and Magnesium Alloys)

To find similar documents by classification:

77.150.10 (Aluminium products)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

 

Customers who bought this document also bought:

ASTM-A480
Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip

ASTM-A240
Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

ASTM-A484
Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings

Document Number

ASTM-B211M-12e1

Revision Level

2012(E1) EDITION

Status

Superseded

Modification Type

Replaced

Publication Date

June 30, 2012

Document Type

Specification

Page Count

10 pages

Committee Number

B07.03