ASTM-B322 Standard Guide for Cleaning Metals Prior to Electroplating

ASTM-B322 - 1999 R20(E1) EDITION - CURRENT
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:

Standard Guide for Cleaning Metals Prior to Electroplating
ORDER

Price:

$63.00        


Want this as a site license?

Scope

1.1 This practice describes the procedure for cleaning metal surfaces to obtain good adhesion of electrodeposited metals. The degree of cleanliness required for metals to be electroplated is greater than for most other finishes. Methods of removal of heat-treat or mill scale are not included in these methods, because they are covered in practices referring to specific metals. It should also be understood that while these procedures are broadly applicable, particular substrates may require certain specific cleaning procedures.

1.2 Adequate cleaning requires a proper combination of cleaning procedures. The choice of these procedures must be based on a knowledge of the metals to be cleaned and of the soils to be removed. Because most experience and knowledge in cleaning have been obtained by suppliers of proprietary processes and formulations, these sources should be consulted before setting up a cleaning process.

1.3 A treatment to remove tarnish, light rust, fingerprints, or oxides is usually provided before immersion of the piece in the electroplating tank. This treatment activates the metal and is usually accomplished in acid baths which also serve to neutralize the residual alkaline film from alkaline cleaning. Alkaline chelated derusting and cleaning solutions, alone or with sodium cyanide, used as a soak or electrocleaner, are often preferred before electroplating on ferrous alloys.

1.4 Invariably several stages are necessary to provide adequate cleaning. These stages are discussed in three parts: Part I -Precleaning (use of a solvent, emulsion, or alkaline spray) to remove the bulk of the soil. Part II -Intermediate (alkaline) cleaning. Part III -Final electrocleaning, to remove trace solids and especially adherent impurities. Part IV -Trouble shooting. Often, depending largely on the amount and type of soil on the workpieces as received, one or more of these stages may be eliminated or modified. Usually, even with light soils, it is advisable to retain multistage cleaning, thereby increasing the life and efficiency of the cleaning solutions.

1.5 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (For more specific safety precautionary statements see Sections 11 and 16.)

Keywords

Cleaning-metal cleaners; Cleaning-surface descaling/cleaning; Coatings-metallic; Descaling; Electroplated coatings; Specimen preparation (general)-electroplating; cleaning metals prior to electroplating, practice; ICS Number Code 25.220.40 (Metallic coatings)

To find similar documents by ASTM Volume:

02.05 (Metallic and Inorganic Coatings; Metal Powders and Metal Powder Products)

To find similar documents by classification:

25.220.40 (Metallic coatings Including electrolytic depositions, cathodic coatings, autocatalytic coatings, etc.)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

 

Customers who bought this document also bought:

ASTM-B633
Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel

ASTM-B117
Standard Practice for Operating Salt Spray (Fog) Apparatus

ASTM-A967
Standard Specification for Chemical Passivation Treatments for Stainless Steel Parts

Document Number

ASTM-B0322-99R20E01

Revision Level

1999 R20(E1) EDITION

Status

Current

Modification Type

Revision

Publication Date

Dec. 7, 2020

Document Type

Guide

Page Count

9 pages

Committee Number

B08.02