ASTM-B632 Standard Specification for Aluminum-Alloy Rolled Tread Plate

ASTM-B632 - 2015 EDITION - CURRENT -- See the following: ASTM-B632M
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:


This specification covers aluminum-alloy rolled tread plate. Unless otherwise specified, all tread plate shall be supplied in the mill finish and shall be uniform as defined by the requirements and shall be commercially sound. The tread plate shall conform to the required chemical composition limits specified. The determination of chemical composition shall be made in accordance with suitable chemical (test methods E 34) or spectrochemical (test methods E 607 and E 1251) methods. Heat treatment for the applicable tempers of alloy 6061 shall be in accordance with practice B 918. The tread plate shall conform to the tensile properties specified. The tension test shall be made in accordance with test methods B 557. The bend tests shall be made in accordance with test method E 290.

ORDER

Price:

$46.00        

Changes from the previous issue

A redline edition is available for this document, with all changes visible. Ask Document Center Inc. for more information.

Scope

1.1 This specification covers aluminum-alloy rolled flat tread plate, mill-finish, with a raised pattern on one side, in the alloy, tempers, and thicknesses shown in Table 1 and Table 2 [Table 3].

(A) Limits in weight percent maximum unless shown as a range or minimum
(B) Analysis shall be made for the elements for which limits are shown in this table.
(C) For purposes of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit, in accordance with the rounding off method of Practice E29.
(D) Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic Others elements. Should any analysis by the producer or purchaser establish that an Others element exceed the limit of Each or that the aggregate of several Others elements exceeds the limit of Total, the material shall be considered non-conforming.
(E) Other Elements—Total shall be the sum of unspecified metallic elements 0.010 % or more, rounded to the second decimal before determining the sum.
(F) In case there is a discrepancy in the values listed in Table 1 with those listed in the “International Alloy Designations and Chemical Composition Limits for Wrought Aluminum and Wrought Aluminum Alloys” (known as the “Teal Sheets”), the composition limits registered with the Aluminum Association and published in the “Teal Sheets” shall be considered the controlling composition. The “Teal Sheets” are available at http://www.aluminum.org/tealsheets.
(A) To determine conformance to this specification, each value for tensile strength and for yield strength shall be rounded to the nearest 0.1 ksi and each value for elongation to the nearest 0.5 %, both in accordance with the rounding-off method of Practice E29.
(B) See Annex A1 for the basis for establishment of mechanical property limits.
(C) For sheet and plate under 1/2 in. in thickness, the standard 1/2 in. wide rectangular tension test specimen shall be used.
(D) The specimen diameter is represented by D.
(E) This temper is not available from the material producer.
(A) To determine conformance to this specification, each value for tensile strength and for yield strength shall be rounded to the nearest 1 MPa and each value for elongation to the nearest 0.5 %, both in accordance with the rounding-off method of Practice E29.
(B) See Annex A1 for the basis for establishment of mechanical property limits.
(C) For sheet and plate through 12.50 mm in thickness, the standard 12.50-mm wide tension rectangular test specimen shall be used.
(D) The specimen diameter is represented by D.
(E) This temper is not available from the material producer.

1.2 Alloy and temper designation are in accordance with ANSI H35.1/H35.1M. The equivalent Unified Numbering System alloy designation are those of Table 1 preceded by A9, which is A96061 for alloy 6061 and A93003 for Alloy 3003 in accordance with Practice E527.

1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.

1.4 The values stated in either inch-pound or SI units are to be regarded separately as standard. The SI units are shown either in brackets or in separate tables. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems will result in nonconformance with the specification.

Keywords

ICS Number Code 77.150.10 (Aluminium products)

To find similar documents by ASTM Volume:

02.02 (Aluminum and Magnesium Alloys)

To find similar documents by classification:

77.150.10 (Aluminium products)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

Document Number

ASTM-B632/B632M-15

Revision Level

2015 EDITION

Status

Current

Modification Type

Revision

Publication Date

Nov. 1, 2015

Document Type

Specification

Page Count

7 pages

Committee Number

B07.03