ASTM-B767 Standard Guide for Determining Mass Per Unit Area of Electrodeposited and Related Coatings by Gravimetric and Other Chemical Analysis Procedures

ASTM-B767 - 1988 R21 EDITION - CURRENT
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:

Standard Guide for Determining Mass Per Unit Area of Electrodeposited and Related Coatings by Gravimetric and Other Chemical Analysis Procedures
ORDER

Price:

$54.00        


Want this as a site license?

Scope

1.1 This guide outlines a general method for determining the mass per unit area of electrodeposited, electroless, mechanically-deposited, vacuum-deposited, anodicoxide, and chemical conversion coatings by gravimetric and other chemical analysis procedures.

1.2 This guide determines the average mass per unit area over a measured area.

1.3 The stripping methods cited are described in specifications or in the open literature or have been used routinely by at least one laboratory.

1.4 The procedures outlined can be used for many coating-substrate combinations. They cannot be used where the coating cannot be separated from the substrate by chemical or physical means as would be the case if white brass were plated with yellow brass.

1.5 In principle, these procedures can be used to measure very thin coatings or to measure coatings over small areas, but not thin coatings over small areas. The limits depend on the required accuracy. For example, 2.5 mg/cm of coating might require 2.5 mg of coating covering 1 cm , but 0.1 mg/cm of coating would require 25 cm to obtain 2.5 mg of coating.

1.6 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Keywords

acceptance criteria/testing; aluminum coatings; average mass per unit area; brass-electrodeposition; cadmium-metallic coatings; chemical analysis; chromate coatings; chromium-coatings; coatings-aluminum; coatings-anodic; coatings-chromate; coatings-mechanically deposited; coatings-phosphate; coating thickness; copper-electrodeposited coatings; density-metallic coatings; gold-electrodeposited coating; gravimetric method; lead-tin; linear changes/linearity; mass-mass per unit area; micrometer; microroughness; microscopic examination-metallic/inorganic coatings; nickel-electrodeposition; planimetric procedure; silver-electrodeposition; terne plate; tin-electrodeposited coatings; tin-lead; vernier caliper; weight; zinc alloys-electrodeposited coatings; mass per unit area-electrodeposited/related coatings, by; gravimetric/other chemical analysis procedures, guide

To find similar documents by ASTM Volume:

02.05 (Metallic and Inorganic Coatings; Metal Powders and Metal Powder Products)

To find similar documents by classification:

25.220.40 (Metallic coatings Including electrolytic depositions, cathodic coatings, autocatalytic coatings, etc.)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

 

Customers who bought this document also bought:

ASTM-E384
Standard Test Method for Microindentation Hardness of Materials

MIL-G-45204
Gold Plating, Electrodeposited (Renumbered MIL-DTL-45204)

MIL-STD-202
Test Method Standard for Electronic and Electrical Component Parts

Document Number

ASTM-B0767-88R21

Revision Level

1988 R21 EDITION

Status

Current

Modification Type

Reapproval

Publication Date

Nov. 1, 2021

Document Type

Guide

Page Count

6 pages

Committee Number

B08.10