ASTM-D2559 › Standard Specification for Adhesives for Bonded Structural Wood Products for Use Under Exterior Exposure Conditions
The following bibliographic material is provided to assist you with your purchasing decision:
This specification covers adhesives suitable for the bonding of wood, including treated wood, into structural laminated wood products for general construction, for marine use, or for other uses where a high-strength, waterproof adhesive bond is required. The requirements of the adhesive are based on the performance of the adhesive in laminated wood as measured by the following test methods: resistance to shear by compression loading; resistance to delamination during accelerated exposure to wetting and drying; and resistance to deformation under static load. The wood shall be prepared by ambient curing and hot press curing.
Scope
1.1 This specification covers adhesives suitable for the bonding of wood, including treated wood, into structural wood products for general construction or other uses where a high-strength, durable adhesive bond is required.
1.2 This specification includes test methods that may be referenced by specific product standards for the evaluation and approval of structural wood adhesives. Methods are included to evaluate adhesives intended for use in exterior exposure.
Note 1: Consult the Commentary in Appendix X1 regarding the intent and limitations of each test method contained in this specification.
1.3 Description of Bondline Performance—It is recognized that structural wood adhesives are used in various applications and levels of severity in terms of moisture content, loading, cyclic and seasonal weather conditions, heat exposure and other use conditions. It is the intent of this standard to determine the suitability of an adhesive for use under various levels of severity and conditions with specific and appropriate test methods and requirements.
Note 2: This specification does not contain specific tests outlined for different chemical types of adhesives.
1.4 Strength and durability requirements of the adhesive are based on the performance of the adhesive in laminated wood as measured by:
1.4.1 Resistance to shear by compression loading after conditioning to the target moisture content indicated in 14.2.3 and meeting requirements in 14.4.
1.4.2 Resistance to delamination during exposure to three cycles of vacuum pressure wetting followed by drying at elevated temperature as indicated in 15.3 and meeting requirements in 15.4.
1.4.3 Resistance to creep under static load by subjecting test specimens to a specified shear stress and exposing one set of test specimens to an environment of elevated temperature and ambient humidity and another set to an environment of high humidity and meeting requirements set forth in 16.3.
1.4.4 For applications involving chemical treatment, the adhesive shall be evaluated using representative samples of treated wood.
Note 3: When using chemically treated wood, compatibility between the treatment, adhesive, and wood is to be considered and agreed upon between the chemical manufacture and the user.
Note 4: Additional durability testing may also be required as specified by individual product standards. Consult the Commentary in Appendix X1 for additional information and guidance as to the type of durability testing that may be appropriate to supplement this specification when characterizing the adhesive for suitability with specific wood products.
1.5 The evaluation of adhesives for use in ground contact and marine exposures are beyond the scope of this specification.
1.6 The evaluation of binder adhesives is beyond the scope of this specification.
1.7 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.
1.8 The text of this specification references notes, footnotes and a commentary which provide explanatory material. These notes, footnotes and commentary (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Keywords
adhesive; delamination; durability; exterior exposure; glulam; laminated wood; shear strength; structural-glued-laminated timber;; ICS Number Code 79.060.10 (Plywood)
To find similar documents by ASTM Volume:
To find similar documents by classification:
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Customers who bought this document also bought:
ASME-Y14.5MDimensioning and Tolerancing (Correctly Numbered ASME-Y14.5)
ASTM-D4066
Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM-A582
Standard Specification for Free-Machining Stainless Steel Bars
Document Number
ASTM-D2559-12a(2018)
Revision Level
2012A R18 EDITION
Status
Current
Modification Type
Reapproval
Publication Date
Aug. 1, 2018
Document Type
Specification
Page Count
14 pages
Committee Number
D14.30