ASTM-D3977 Standard Test Methods for Determining Sediment Concentration in Water Samples

ASTM-D3977 - 1997 R13(E1) EDITION - CURRENT
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:

Standard Test Methods for Determining Sediment Concentration in Water Samples
ORDER

Price:

$52.00        


Want this as a site license?

Scope

1.1 These test methods cover the determination of sediment concentrations in water and wastewater samples collected from lakes, reservoirs, ponds, streams, and other water bodies. In lakes and other quiescent-water bodies, concentrations of sediment in samples are nearly equal to concentrations at sampling points; in most instances, sample concentrations are not strongly influenced by collection techniques. In rivers and other flowing-water bodies, concentrations of sediment in samples depend upon the manner in which the samples are collected. Concentrations in isokinetically-collected samples can be multiplied by water discharges to obtain sediment discharges in the vicinity of the sampling points.

1.2 The procedures given in these test methods are used by the Agricultural Research Service, Geological Survey, National Resources Conservation Service, Bureau of Reclamation, and other agencies responsible for studying water bodies. These test methods are adapted from a laboratory-procedure manual2 and a quality-assurance plan.3

1.3 These test methods include:

 

Sections

Test Method A—Evaporation

 8 to 13

Test Method B—Filtration

14 to 19

Test Method C—Wet-sieving-filtration

20 to 25


1.4 Test Method A can be used only on sediments that settle within the allotted storage time of the samples which usually ranges from a few days to a few weeks. A correction factor must be applied if dissolved-solids concentration exceeds about 10 % of the sediment concentration.

1.5 Test Method B can be used only on samples containing sand concentrations less than about 10 000 ppm and clay concentrations less than about 200 ppm. The sediment need not be settleable because filters are used to separate water from the sediment. Correction factors for dissolved solids are not required.

1.6 Test Method C can be used if two concentration values are required: one for sand-size particles and one for the combination of silt and clay-size particles. The silt-clay fraction need not be settleable.

1.7 These test methods must not be confused with turbidity measurements discussed in Test Method D1889. Turbidity is the optical property of a sample that causes light rays to be scattered and absorbed; it is not an accurate measure of the mass or concentration of sediment in the sample.

1.8 These test methods contain some procedures similar to those in Test Methods D1888 which pertains to measuring particulate and dissolved matter in water.

1.9 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Significance and Use

4.1 Suspended-sediment samples contain particles with a wide variety of physical characteristics. By presenting alternate approaches, these test methods allow latitude in selecting analysis methods that work best with the particular samples under study.

4.2 Sediment-concentration data are used for many purposes that include: (1) computing suspended-sediment discharges of streams or sediment yields of watersheds, (2) scheduling treatments of industrial and domestic water supplies, and (3) estimating discharges of pesticides, plant nutrients, and heavy metals transported on surfaces or inside sediment particles.

Keywords

fluvial sediment; sediment; sediment concentration

To find similar documents by ASTM Volume:

11.02 (Water (II))

To find similar documents by classification:

13.060.30 (Sewage water Including sewage water disposal and treatment Liquid wastes, see 13.030.20 Drainage systems, see 91.140.80 Sewage systems, see 93.030)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

Document Number

ASTM-D3977-97(2013)e1

Revision Level

1997 R13(E1) EDITION

Status

Current

Modification Type

Editorially changed

Publication Date

Jan. 1, 2014

Document Type

Test Method

Page Count

7 pages

Committee Number

D19.07