ASTM-D5537 Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration

ASTM-D5537 - 2023A EDITION - CURRENT
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:

Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration
ORDER

Price:

$90.00        


Want this as a site license?

Scope

1.1 This is a fire-test-response standard.

1.2 This test method provides a means to measure the heat released by burning the electrical insulating materials contained in electrical or optical fiber cables when the cable specimens, excluding accessories, are subjected to a specified flaming ignition source and burn freely under well ventilated conditions. Flame propagation cable damage, by char length, and mass loss are also measured.

1.3 This standard provides two different protocols for exposing the materials, when made into cable specimens, to an ignition source (approximately 20 kW), for a 20 min test duration. Use it to determine the heat release, flame propagation and mass loss characteristics of the materials contained in single and multiconductor electrical or optical fiber cables.

1.4 This test method does not provide information on the fire performance of materials insulating electrical or optical fiber cables in fire conditions other than the ones specifically used in this standard nor does it measure the contribution of the materials in those cables to a developing fire condition.

1.5 Data describing the burning behavior from ignition to the end of the test are obtained.

1.6 This test equipment is suitable for making other measurements, including the smoke released by the burning specimen (Test Method D5424) and the concentrations of certain toxic gas species in the combustion gases (see Appendix X4).

1.7 The values stated in SI units are the standard (see Practice E380); the values stated in parentheses are for information only.

1.8 This standard should be used to measure and describe the response of materials, products or assemblies to heat and flame under controlled conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire hazard or fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard or fire risk of a particular end use.

1.9 Fire testing of products and materials is inherently hazardous. Employ adequate safeguards for personnel and property in conducting these tests.

1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Keywords

Cable; Calorimeter; Char; Electrical cable; Electrical insulating solids; Fire testing-electrical insulating materials; Fire-test response; Flame heat release; Heat release rate; Optical fiber cable; Oxygen consumption calorimetry; insulating materials contained in electrical/optical fiber cables-heat; release/flame spread/mass loss, when burning in vertical cable tray; configuration, test,; Electrical insulating solids; heat release/flame spread/mass loss-insulating materials contained in; electrical/optical fiber cables, when burning in vertical cable tray; configuration, test,; Volumetric flow; volumetric flow rate-insulating materials contained in; electrical/optical fiber cables, when burning in vertical cable tray; configuration, annex,; Mass flow; mass flow rate-insulating materials contained in electrical/optical; fiber cables, when burning in vertical cable tray configuration, annex,; Rate of heat release; Symbols; rate of heat release-insulating materials contained in; electrical/optical fiber cables, equations/symbols, annex; ICS Number Code 13.220.40 (Ignitability and burning behaviour of materials and products); 29.035.01 (Insulating materials in general)

To find similar documents by ASTM Volume:

10.02 (Electrical Insulation (II): D2518 - latest)

To find similar documents by classification:

13.220.40 (Ignitability and burning behaviour of materials and products)

29.035.01 (Insulating materials in general)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

Document Number

ASTM-D5537-23A

Revision Level

2023A EDITION

Status

Current

Modification Type

New

Publication Date

May 18, 2023

Document Type

Test Method

Page Count

21 pages

Committee Number

D09.21