ASTM-D584 › Standard Test Method for Wool Content of Raw Wool—Laboratory Scale
The following bibliographic material is provided to assist you with your purchasing decision:
Scope
1.1 This test method covers a laboratory procedure for the determination of the wool base content and the clean wool fiber present in samples of raw wool. This test method is also applicable to other animal fibers such as mohair, cashmere, alpaca, and camel hair.
Note 1: Sampling of lots of raw wool in packages is covered in Practice D1060; the determination of vegetable matter and other alkali-insoluble impurities in scoured wool is covered in Test Method D1113; the determination of wool content on a commercial scale is covered in Test Method D1334. For factors for the conversion of woolbase content to its equivalent in terms of scoured wool, top, or noil of various commercially specified compositions (formerly covered in the appendix of this test method), refer to Practice D2720.
Note 2: Because of the trade practice the term weight is used in this test method instead of the technically correct term mass.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Significance and Use
5.1 This test method is considered satisfactory for acceptance testing of commercial shipments since this test method has been used extensively in the trade for acceptance testing.
5.1.1 In case of dispute arising from differences in reported test results when using Test Method D584 for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative testing to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogenous as possible and that are from a lot of the type material in question. The test specimens should then be assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two parties before testing is begun. If a bias is found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret future test results in the light of known bias.
5.2 The wool-base content of wool in any condition or form is a basic quantity. From it may be calculated commercial masses or yields in any of the various recognized defined systems used in international commerce (Note 1).
5.2.1 The procedures for determining the wool base content of greasy wool provided in this test method and in IWTO Method 19-85(E) are in essential agreement.
Note 3: This is not true for scoured wool, as IWTO Method 19-85(E) does not require rescouring of scoured wool containing less than 5 % residual grease.
5.3 Not all of the wool base present in a lot of raw wool can be recovered in useful form by commercial cleaning operations. The amount of wool loss varies, depending on factors such as the character of the wool, the nature and percentage of the impurities present, the cleaning process and equipment used, and so forth.
5.4 No ASTM standard specifies or recommends any specific procedure or practice for estimating anticipated loss of wool during commercial cleaning (or other) operations. The following statutory practice is described solely for information:
5.4.1 For the purpose of duty assessment on importations of raw wool into the United States, the Tariff Schedules of the United States5 provides a statutory formula for calculating the allowance to be made for wool “that would ordinarily be lost during commercial cleaning operations.” The formula is based on the clean wool fiber present (called “absolute clean content” in the Tariff Schedules) and on the vegetable matter present. The allowance, in terms of clean wool fiber present, is equal to 0.5 % of the clean wool fiber present plus 60 % of the vegetable matter present, the total allowance not to exceed 15 % of the clean wool fiber present. The dutiable quantity (called “clean yield” in the Tariff Schedules) is the difference between the clean wool fiber present and the allowance so calculated.
Keywords
clean wool content; raw wool; yield ;; ICS Number Code 59.060.10 (Natural fibres)
To find similar documents by ASTM Volume:
07.01 (Textiles (I): D76 - D4391)
To find similar documents by classification:
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Customers who bought this document also bought:
Q7-PACKSupplier Quality Requirements 5-Pack - Recommended Quality Manuals commonized by Chrysler, Ford Motor Company, & General Motors: APQP, PPAP, FMEA, MSA, & SPC
EIA-383
Preparation for the Delivery of Electrical & Electronic Components
ISO-9000 COMPENDIUM
ISO 9000 - Quality Management (12th Edition Compendium)
Document Number
ASTM-D584-10(2018)
Revision Level
2010 R18 EDITION
Status
Current
Modification Type
Reapproval
Publication Date
July 1, 2018
Document Type
Test Method
Page Count
6 pages
Committee Number
D13.13