ASTM-D5848 Standard Test Method for Mass Per Unit Area of Pile Yarn Floor Coverings

ASTM-D5848 - 2020 EDITION - CURRENT
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:

Standard Test Method for Mass Per Unit Area of Pile Yarn Floor Coverings
ORDER

Price:

$69.00        


Want this as a site license?

Scope

1.1 This test method covers the measurement of mass per unit area of machine-made woven, knitted, and tufted pile yarn floor covering both before and after an adhesive-back coating application.

1.2 This test method encompasses three techniques for determination of mass per unit area as applicable:

1.2.1 Section 7, for determining total mass per unit area, applies to both coated and uncoated (unfinished) pile floor coverings.

1.2.2 Section 8, for determining component mass per unit area, applies only to uncoated (unfinished) pile yarn floor coverings.

1.2.3 Section 9, for determining pile yarn mass per unit area, applies only to back-coated, or finished, pile yarn floor coverings.

1.3 Determination of mass per unit area of pile yarn floor coverings was previously contained within Test Methods D418. For user convenience, Subcommittee D13.21 subdivided Test Methods D418 into separate standards, of which this test method is one.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only (except where shown in 1.4.1) and are not considered standard.

1.4.1 The following sections are measured in SI units: Table 1, sections 9.8.4.2, 9.8.6.3 to 9.8.6.10, A2.1, A2.2, and A2.3.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 9.5.

1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Significance and Use

4.1 The determination of the mass per unit area of pile yarn floor covering is useful in quality and cost control during the manufacture of pile floor covering. Both appearance and performance may be affected by changes in mass per unit area.

4.2 In case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and supplier should conduct comparison testing to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of material of the type in question. The test specimens should then be randomly assigned to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two parties prior to testing. If a bias is found, either its cause must be found and corrected or the purchaser and supplier must agree to interpret future test results with consideration to the known bias.

Keywords

carpet; construction; floor covering; mass per unit area; pile yarn;

To find similar documents by ASTM Volume:

07.02 (Textiles (II): D4393 - latest)

To find similar documents by classification:

59.080.60 (Textile floor coverings)

97.150 (Non-textile floor coverings Textile floor coverings, see 59.080.60)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

Document Number

ASTM-D5848-20

Revision Level

2020 EDITION

Status

Current

Modification Type

Reinstated

Publication Date

Feb. 1, 2020

Document Type

Test Method

Page Count

13 pages

Committee Number

D13.21