ASTM-D6262 Standard Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK)

ASTM-D6262 - 2023 EDITION - CURRENT
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:


This specification covers requirements and methods of test for the material, dimensions, and workmanship, and the properties of extruded, compression molded, and injection molded PAEK sheet, plate, rod, and tubular bar manufactured from PAEK. The type of PAEK extruded, compression molded, and injection molded product may be categorized by type, grade and class depending on resin and filler compositions. Every type of PAEK shape may be categorized into one of several grades as follows: Grade 1 (general purpose) which is extruded, compression molded or injection molded product made using only 100% virgin PAEK resin and Grade 2 (recycle grade) which is extruded, compression molded or injection molded product made using any amount up to 100% of recycled thermoplastic PAEK. The type, class and grade is further differentiated based on dimensional stability. Different tests shall be conducted in order to determine the following properties of PAEK: tensile stress at break, elongation at break, tensile modulus, dimensional stability, lengthwise camber and widthwise bow, squareness, flexural modulus, and Izod impact.

ORDER

Price:

$63.00        


Want this as a site license?

Scope

1.1 This specification covers requirements for the PAEK materials used and the requirements and methods of test for the dimensions, workmanship, and the properties of extruded, compression molded, and injection molded PAEK sheet, plate, rod, and tubular bar manufactured from PAEK. PAEK is a family of thermoplastic materials that differ in properties (see Section 3).

1.2 The properties included in this specification are those required for the compositions covered. Requirements necessary to identify particular characteristics important to specialized applications are described by using the classification system given in Section 4.

1.3 This specification allows the use of key clad plastics (see Section 4).

1.4 The values are stated in inch-pound units and are regarded as the standard in all property and dimensional tables. For reference purposes, SI units are also included in Table 1.

1.5 The following precautionary caveat pertains only to the test method portion Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Note 1: There is no known ISO equivalent to this standard.

1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Keywords

PAEK; PEEK; PEKK; plates–PAEK; recycled–PAEK; recycled plastic; rod-PAEK; shapes–PAEK; sheet-PAEK; tubular bar-PAEK;

To find similar documents by ASTM Volume:

08.03 (Plastics (III): D5117 - latest; Reinforced Plastic Piping Systems and Chemical Equipment; Plastic Building Products)

To find similar documents by classification:

83.140.99 (Other rubber and plastics products)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

 

Customers who bought this document also bought:

ASTM-A276
Standard Specification for Stainless Steel Bars and Shapes

ASTM-A240
Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

ASTM-A484
Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings

Document Number

ASTM-D6262-23

Revision Level

2023 EDITION

Status

Current

Modification Type

Revision

Publication Date

Aug. 16, 2023

Document Type

Specification

Page Count

7 pages

Committee Number

D20.15