ASTM-D6338 Standard Classification System for Highly Crosslinked Thermoplastic Vulcanizates (HCTPV) Based on ASTM Standard Test Methods

ASTM-D6338 - 2017 EDITION - CURRENT
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:

Standard Classification System for Highly Crosslinked Thermoplastic Vulcanizates (HCTPV) Based on ASTM Standard Test Methods
ORDER

Price:

$63.00        


Want this as a site license?

Changes from the previous issue

A redline edition is available for this document, with all changes visible. Ask Document Center Inc. for more information.

Scope

1.1 This classification system covers highly crosslinked thermoplastic vulcanizates (HCTPV) for extrusion, molding and other fabrication methods. Highly crosslinked thermoplastic vulcanizates (HCTPV) are thermoplastic elastomers (TPE) consisting of two or more polymer systems at least one of which is rubbery and highly (>95 %) crosslinked and at least one of which is thermoplastic, with each system having its own phase. The thermoplastic phase will tend to be continuous and the rubbery phase discontinuous. The high level of crosslinking and ultrafine particle size (ca 1 μm diameter) of the rubbery phase give rise to properties more closely approaching those of conventional thermoset rubber, when compared to the same thermoplastic/rubbery polymer composition with a lower level (95 %) of crosslinking. The HCTPV polymer compositions may contain fillers, reinforcing agents, plasticizers, resins, antidegradants, colorants and other beneficial constituents. Recycled HCTPV are not covered in this classification system.

1.2 The properties included in this standard are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be specified by using suffixes as given in Section 5.

1.3 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastic field only after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this standard.

1.4 As given in IEEE/ASTM SI-10, values in SI units are to be regarded as standard.

Note 1: There is no known ISO equivalent to this standard.

1.5 This standard is based on testing completed in accordance with ASTM standard test methods.

1.6 The following safety hazards caveat pertains only to the test methods portion, Section 11, of this classification system. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Keywords

dynamic vulcanization; highly crosslinked thermoplastic vulcanizate; line callout; thermoplastic elastomer; thermoplastic vulcanizate;; ICS Number Code 83.080.20 (Thermoplastic materials)

To find similar documents by ASTM Volume:

08.03 (Plastics (III): D5117 - latest; Reinforced Plastic Piping Systems and Chemical Equipment; Plastic Building Products)

To find similar documents by classification:

83.080.20 (Thermoplastic materials)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

Document Number

ASTM-D6338-17

Revision Level

2017 EDITION

Status

Current

Modification Type

Revision with Title Change

Publication Date

Sept. 15, 2017

Document Type

Classification

Page Count

6 pages

Committee Number

D20.15