ASTM-D6727 Standard Guide for Conducting Borehole Geophysical Logging—Neutron

ASTM-D6727 - 2016 EDITION - CURRENT
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:

Standard Guide for Conducting Borehole Geophysical Logging—Neutron
ORDER

Price:

$63.00        


Want this as a site license?

Changes from the previous issue

A redline edition is available for this document, with all changes visible. Ask Document Center Inc. for more information.

Scope

1.1 This guide is focused on the general procedures necessary to conduct neutron or neutron porosity (hereafter referred to as neutron) logging of boreholes, wells, access tubes, caissons, or shafts (hereafter referred to as boreholes) as commonly applied to geologic, engineering, groundwater and environmental (hereafter referred to as geotechnical) explorations. Neutron soil moisture measurements made using neutron moisture gauges, are excluded. Neutron logging for minerals or petroleum applications is excluded, along with neutron activation logs where gamma spectral detectors are used to characterize the induced gamma activity of minerals exposed to neutron radiation.

1.2 This guide defines a neutron log as a record of the rate at which thermal and epithermal neutrons are scattered back to one or more detectors located on a probe adjacent to a neutron source.

1.2.1 Induction logs are treated quantitatively and should be interpreted with other logs and data whenever possible.

1.2.2 Neutron logs are commonly used to: (1) delineate lithology, and (2) indicate the water-filled porosity of formations (see Fig. 1).

Nc   =   corrected neutron log, N0   =   original neutron log, Csh   =   computed shale fraction based upon the gamma log position between the endpoints of 10 and 120 cps, and Φsh   =   estimate of shale non-effective porosity of about 40 % picked from intervals on the log where Φsh = 1.0.

1.3 This guide is restricted to neutron logging with nuclear counters consisting of scintillation detectors (crystals coupled with photomultiplier tubes), or to He3-tube detectors with or without Cd foil covers or coatings to exclude thermalized neutrons.

1.4 This guide provides an overview of neutron logging including: (1) general procedures; (2) specific documentation; (3 ) calibration and standardization, and (4) log quality and interpretation.

1.5 To obtain additional information on neutron logs see References section in this guide.

1.6 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This guide should not be used as a sole criterion for neutron logging and does not replace education, experience, and professional judgment. Neutron logging procedures should be adapted to meet the needs of a range of applications and stated in general terms so that flexibility or innovation are not suppressed. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged without consideration of a project's many unique aspects. The word standard in the title of this document means that the document has been approved through the ASTM consensus process.

1.7 Units—The values stated in either inch-pound units or SI units given in brackets are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be use independently of the other. Combining values from the two systems may result in non-conformance with the standard. Add if appropriate: “Reporting of test results in units other than SI shall not be regarded as nonconformance with this standard.”

1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. The use of radioactive sources in neutron logging introduces significant safety issues related to the transportation and handling of neutron sources, and in procedures to ensure that sources are not lost or damaged during logging. There are different restrictions on the use of radioactive sources in logging in different states, and the Nuclear Regulatory Agency (NRC) maintains strict rules and regulations for the licensing of personnel authorized to conduct nuclear source logging.

Significance and Use

5.1 An appropriately developed, documented, and executed guide is essential for the proper collection and application of neutron logs.

5.2 The benefits of its use include improving selection of neutron logging methods and equipment; neutron log quality and reliability; usefulness of the neutron log data for subsequent display and interpretation.

5.3 This guide applies to commonly used neutron logging methods for geotechnical applications.

Keywords

borehole geophysics; neutron log; neutron porosity log; well construction; well logging;; ICS Number Code 93.020 (Earthworks. Excavations. Foundation construction. Underground works)

To find similar documents by ASTM Volume:

04.09 (Soil and Rock (II): D5877 - latest)

To find similar documents by classification:

07.060 (Geology. Meteorology. Hydrology)

93.020 (Earthworks. Excavations. Foundation construction. Underground works Including geotechnics Earth-moving machinery, see 53.100)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.