ASTM-F1667 › Historical Revision Information
Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
The following bibliographic material is provided to assist you with your purchasing decision:
This specification covers nails, spikes, staples, and other fasteners driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine. The driven fasteners are classified as type I: nails (NL); type II: cut nails (CN); type III: spikes (SP); and type IV: staples (ST). Materials shall be tested and the individual types shall conform to the material requirements and physical properties, such as ductility, tensile strength. Protective coating and finishes are also detailed.
Scope
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.
Note 1: Fastener ductility information is presented in Table 2 and dimensional information in Tables 3–65.
† Editorially corrected in March 2012.
| L | = | length, in., |
| H | = | head diameter, in., |
| TL | = | length of threaded shank, in., |
| max | = | maximum acceptable value (not subject to tolerances), |
| min | = | minimum acceptable value (not subject to tolerances), |
| D | = | shank diameter, in., |
| T1 | = | crest diameter, in., and |
| P | = | pitch, or spacing of threads, in. |
| L | = | length, in., |
| H | = | head diameter, in., |
| TL | = | length of threaded shank, in., |
| max | = | maximum acceptable value (not subject to tolerances), |
| min | = | minimum acceptable value (not subject to tolerances), |
| D | = | shank diameter, in., |
| T1 | = | crest diameter, in., and |
| P | = | pitch, or spacing of threads, in. |
| Dimensions and Tolerances for Gages of Flat Top Crown Staples | |||||||||||||
|
|
| 10 Gage | 12 Gage | 14 Gage | 15 Gage | 16 Gage | 18 Gage | ||||||
|
|
| T | W | T | W | T | W | T | W | T | W | T | W |
| Nominal |
| .1250 | .1400 | .0935 | .1120 | .0735 | .0855 | .0673 | .073 | .0563 | .064 | .038 | .050 |
| Maximum |
| .1290 | .1440 | .0975 | .1160 | .0775 | .0895 | .0731 | .076 | .0626 | .068 | .0415 | .0532 |
| Minimum |
| .1210 | .1360 | .0895 | .1080 | .0695 | .0815 | .0615 | .070 | .0500 | .060 | .0345 | .0468 |
| Tolerance | ± | .0040 | .0040 | .0040 | .0040 | .0040 | .0040 | .0058 | .003 | .0063 | .004 | .0035 | .0032 |
1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Keywords
diameter; driven fasteners; head; length; nails; point; spikes; staples;; ICS Number Code 21.060.01 (Fasteners in general)
To find similar documents by ASTM Volume:
01.08 (Fasteners; Rolling Element Bearings)
To find similar documents by classification:
21.060.01 (Fasteners in general)
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Document Number
ASTM-F1667-15
Revision Level
2015 EDITION
Status
Superseded
Modification Type
Revision
Publication Date
Nov. 1, 2015
Document Type
Specification
Page Count
47 pages
Committee Number
F16.05