Document Center is acquired by Nimonik

1.1 Purpose: 

1.2 Exoskeleton—The exoskeleton shall be used as intended by the manufacturer to perform the test described in this test method. If the exoskeleton is not designed for beam traversing and the test requestor intends to use the exoskeleton to perform a beam test (for example, for research, development of beam-capable use by a manufacturer, beam training as in military applications), appropriate manufacturer approvals should be sought prior to performing the test method.

1.3 Performing Location—This test method shall be performed in a testing laboratory or in the field where the specified apparatus and environmental conditions are implemented.

1.4 Units—The values stated in SI units are to be regarded as the standard. The values given in parentheses are not precise mathematical conversions to inch-pound units. They are close approximate equivalents for the purpose of specifying material dimensions or quantities that are readily available to avoid excessive fabrication costs of test apparatuses while maintaining repeatability and reproducibility of the test method results. These values given in parentheses are provided for information only and are not considered standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

5.1 Beams and beams with platforms can vary greatly in, for example: length, width, height, quantity, geometry, surface coatings, and for a variety of industries. Fig. 2 shows examples of various beams and beams with platforms.

FIG. 2 Example Beams: (a) Steel Construction Beams; (b) Steel Construction Beam to a Platform; (c) Log Construction Beam; (d) Playground Log Beam; (e) Log Beam across Water; and (f) Balance Beam used for Gymnastics

5.2 Exoskeletons are being used in the industrial/occupational, military, response, medical, and recreational sectors to enhance safety and effectiveness of the user to perform tasks. Traversing beams are used in many tasks performed and may include, for example, upper, lower, or full body movement in order to complete the task. Dependent upon the task, it may require people to traverse various ground and beam surfaces while wearing an exoskeleton. For example, an exoskeleton may be used to help during construction tasks where workers in exoskeletons traverse beams or beams and platforms with and without carrying loads, indoors or outdoors, as part of their daily activities. The testing results of exoskeletons shall describe, in a statistically significant way (see guidance in Appendix X1), how reliably the exoskeleton is able to support tasks within the specified types of environments, confinements, and terrains, and thus provide sufficiently high levels of confidence to determine the applicability of the exoskeleton.

5.3 This test method addresses exoskeleton safety and performance requirements expressed by manufacturing, emergency responders, military, or other organizations requesting this test. The safety and performance data captured within this test method are indicative of the test exoskeleton’s and the exoskeleton user’s capabilities. Having available direct information from tested exoskeleton(s) with associated performance data to guide procurement and deployment decisions is essential to exoskeleton purchasers and users.

5.4 The testing results of the candidate exoskeleton(s) shall describe, in a statistically significant way, how reliably the exoskeleton user is able to negotiate beams. The test apparatus described in 6.7 is intended to be a single, standardized beam or beam and platform where repeatable results between exoskeletons, users, and organizations are comparable. The standard test setup and apparatus can also be used to support training and establish proficiency of exoskeleton users, as well as provide manufacturers with information about the usefulness of their exoskeleton(s) for tasks. For guidance on exoskeleton training, see Practice F3444/F3444M.

5.5 Although the test method was developed for the sectors listed in 5.2, it may be applicable to other operational domains.