ASTM-F593 Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs

ASTM-F593 - 2017 EDITION - CURRENT
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:

Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
ORDER

Price:

$45.00        

Changes from the previous issue

A redline edition is available for this document, with all changes visible. Ask Document Center Inc. for more information.

Scope

1.1 This specification covers the requirements for stainless steel bolts, hex cap screws, and studs 0.25 to 1.50 in., inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance.

1.2 Seven groups of stainless steel alloys are covered, including fourteen austenitic, two ferritic, four martensitic, and one precipitation hardening.

Group

AlloysA

ConditionB

1

 304, 305, 384, 304 L,

   (CW) cold workedC

 18-9LW, 302HQ, 304J3D

2

  316, 316 L

   (CW) cold workedC

3

  321, 347

   (CW) cold workedC

4

  430E

   (CW) cold workedC

5

  410F

   (H) hardened and tempered

6

  431

   (H) hardened and tempered

7

  630

   (AH) age hardened

(A) Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer (see 6.1).
(B) See 4.2 for options.
(C) Sizes 0.75 in. and larger may be hot worked and solution annealed, provided the bolts comply with the cold worked (CW) mechanical property requirements.
(D) When approved by the purchaser, Alloys 303, 303Se, or XM1 may be furnished.
(E) When approved by the purchaser, Alloy 430F may be furnished.
(F) When approved by the purchaser, Alloys 416 or 416Se may be furnished.

1.3 Supplementary requirements of an optional nature are provided, applicable only when agreed upon between the manufacturer and the purchaser at the time of the inquiry and order.

1.4 Suitable nuts for use with bolts, hex cap screws, and studs included in this specification are covered by Specification F594. Unless otherwise specified, all nuts used on these fasteners shall conform to the requirements of Specification F594, shall be of the same alloy group, and shall have a specified minimum proof stress equal to or greater than the specified minimum full-size tensile strength of the externally threaded fastener.

1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Keywords

bolts; general use; hex cap screws; stainless; studs;; ICS Number Code 21.060.10 (Bolts, screws, studs)

To find similar documents by ASTM Volume:

01.08 (Fasteners; Rolling Element Bearings)

To find similar documents by classification:

21.060.10 (Bolts, screws, studs)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

Document Number

ASTM-F593-17

Revision Level

2017 EDITION

Status

Current

Modification Type

Revision

Publication Date

June 15, 2017

Document Type

Specification

Page Count

9 pages

Committee Number

F16.04