ASTM-A1058 Standard Test Methods for Mechanical Testing of Steel Products—Metric

ASTM-A1058 - 2019 EDITION - CURRENT
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:

Standard Test Methods for Mechanical Testing of Steel Products—Metric
ORDER

Price:

$76.00        


Want this as a site license?

Scope

1.1 These test methods cover mechanical tests described in ASTM, EN,2 ISO,3 and JIS4 standards that utilize the SI system of units. The test methods in each system are not exact equivalents. Each standards system (ASTM, EN, ISO, and JIS) shall be used independently of the other. Combining requirements from any two or more systems may result in nonconformance with the purchase order.

1.2 These test methods cover procedures for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control.

1.3 Only one of the testing procedure tracks shall be followed: ASTM, EN, ISO, or JIS. When a test method or practice is not available in one of the tracks then an appropriate test method or practice from an alternative track shall be used. The respective tests are listed in the column shown in Table 1.

Note 1: The test methods in each system are not exact equivalents.

1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5 Attention is directed to Practice ISO 17025 when there may be a need for information on criteria for evaluation of testing laboratories.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Keywords

bend test; Brinell hardness; Charpy impact test; elongation; hardness test; portable hardness; reduction of area; Rockwell hardness; tensile strength; tension test; yield strength;

To find similar documents by ASTM Volume:

01.01 (Steel--Piping, Tubing, Fittings)

01.02 (Ferrous Castings; Ferroalloys)

01.03 (Steel--Plate, Sheet, Strip, Wire; Stainless Steel Bar)

01.04 (Steel--Structural, Reinforcing, Pressure Vessel, Railway)

01.05 (Steel--Bars, Forgings, Bearing, Chain, Tool)

To find similar documents by classification:

77.040.10 (Mechanical testing of metals Mechanical testing in general, see 19.060 Mechanical testing of welded joints, see 25.160.40)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

 

Customers who bought this document also bought:

NAS-410
NAS Certification and Qualification of Nondestructive Test Personnel

AWS-D17.1/D17.1M
Specification for Fusion Welding for Aerospace Applications

MIL-H-7199
Heat Treatment of Wrought Copper-Beryllium Alloys, Process for (Copper Alloys: Numbers C17000, C17200, C17300, C17500, and C17510) (Superseded by SAE-AMS-H-7199)

Document Number

ASTM-A1058-19

Revision Level

2019 EDITION

Status

Current

Modification Type

Revision

Publication Date

Nov. 15, 2019

Document Type

Test Method

Page Count

12 pages

Committee Number

A01.13