Document Center List of Standards on Transmissions, Suspensions Including Clutches, Gearboxes, Power-Steering Systems, Cardan Shafts, Differentials, Wheels, Rims, Etc. Tyres For Road Vehicles, See 83.160.10
ICS Code 43.040.50
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
ASTM:
- ASTM-A504 - Standard Specification for Wrought Carbon Steel Wheels
- ASTM-B67 - Standard Specification for Car and Tender Journal Bearings, Lined
- ASTM-D5005 - Test Method for Evaluation of Fluids for Effects on Friction and Wear of Wet Clutches (Withdrawn 1995)
- ASTM-F2803 - Standard Test Method for Evaluating Rim Slip Performance of Tires and Wheels
BSI:
- BS-3092 - Specification for main friction clutches, main power-take-off assemblies and associated attachments for internal combustion engines
- BS-AU-50-1-0C - Tyres and Wheels, Tyres, General
- BS-AU-50-1.0D - Tyres and wheels. Tyres
- BS-AU-50-1.1.1C - Tyres and wheels. Tyres. Car tyres
- BS-AU-50-1.4.5 - Tyres and wheels. Tyres. Agricultural tractor and machine tyres. Specification for designations, dimensions and marking for metric series tyres
- BS-AU-50-1.4.5A - Tyres and wheels. Tyres. Agricultural tractor and machine tyres. Specification for designations, dimensions, marking and tyre/rim coordination for metric series tyres
- BS-AU-50-1.5.5 - Tyres and wheels. Tyres. Industrial vehicle tyres
- BS-AU-50-1.8 - Tyres and wheels. Tyres.
- BS-AU-50-2.0A - Tyres & Wheels, Wheels & Rims, General (Including Terms & Definitions, & Construction
- BS-AU-50-2.0B - Tyres & Wheels, Wheels & Rims, General (Including Vocabulary, Designation & Marking)
- BS-AU-50-2-1B - Tyres and wheels. Wheels and rims. Rim profiles and dimensions (including openings for valves)
- BS-AU-50-2.3 - Tyres and wheels. Wheels and rims
- BS-AU-50-2.7A - Tyres and wheels. Wheels and rims. Code of practice for the selection and care of tyres and wheels for commercial vehicles
- BS-AU-50-2-7B - Tyres and wheels
- BS-AU-50-2.7B - Tyres and wheels
- BS-AU-50-2-8A - Tyres and wheels. Wheels and rims
- BS-AU-50-3.1A - Tyres and wheels. Valves. Specification for valve dimensions
- BS-AU-50-3.1B - Tyres and wheels. Valves. Specification for valve dimensions and designation
- BS-AU-50-3.1C - Tyres and wheels. Valves. Tyre valves. Dimensions and designation
- BS-AU-50-3.1D - Tyres & Wheels, Valves, Tyres & Wheels, Tyre Valves, Dimensions & Designation
- BS-AU-50-3.1E - Tyres and wheels. Valves. Dimensions, designation, valve pressure ratings by use and torque for clamp-in valves
- BS-AU-50-3-2 - Tyres and wheels. Valves
- BS-AU-50-4.1.1 - Tyres and wheels. Rim profiles and dimensions. Car rims. Specification for metric series rims
- BS-AU-50-4.1.1A - Tyres and wheels. Rim profiles and dimensions. Car rims. Specification for metric series rims. Sub-section 1.1a: Specification for metric series rims
- BS-AU-50-4.1A - Tyres and wheels. Rim profiles and dimensions. Car rims. Specification for metric series rims. Sub-section 1.1a: Specification for metric series rims
- BS-AU-50-4.2.1 - Tyres and wheels. Rim profiles and dimensions. Commercial vehicle rims. Specification for metric series rims
- BS-AU-50-4.2.1A - Tyres and wheels. Rim profiles and dimensions. Commercial vehicle rims
- BS-AU-50-4.5.1 - Tyres and wheels. Rim profiles and dimensions. Industrial vehicle rims
- BS-ISO-10597 - Road vehicles. Flat attachment fixing nuts for commercial vehicles. Test methods
- BS-ISO-11425-TC - Tracked Changes. Rubber hoses and hose assemblies for automobile power-steering systems. Specification
- BS-ISO-13988 - Passenger car and light truck vehicle wheels. Clip and adhesive balance weight and rim flange nomenclature, test procedures and performance requirements
- BS-ISO-13988-TC - Tracked Changes. Passenger car and light truck vehicle wheels. Clip and adhesive balance weight and rim flange nomenclature, test procedures and performance requirements
- BS-ISO-14400 - Road vehicles. Wheels and rims. Use, general maintenance and safety requirements and out-of-service conditions
- BS-ISO-14400-TC - Tracked Changes. Road vehicles. Wheels and rims. Use, general maintenance and safety requirements and out-of-service conditions
- BS-ISO-16833 - Road vehicles. Wheels. Measurement of radial and lateral run-out
- BS-ISO-29802 - All-terrain (AT) tyres and rims. Symbol marked pneumatic tyres on 5 tapered rims. Designation, dimension, marking and load ratings
- BS-ISO-3006 - Road vehicles. Passenger car wheels for road use. Test methods
- BS-ISO-3894 - Road vehicles. Wheels/rims for commercial vehicles. Test methods
- BS-ISO-3894-TC - Tracked Changes. Road vehicles. Wheels/rims for commercial vehicles. Test methods
- BS-ISO-3911 - Wheels and rims for pneumatic tyres. Vocabulary, designation and marking
- BS-ISO-3911-TC - Tracked Changes. Wheels and rims for pneumatic tyres. Vocabulary, designation and marking
- BS-ISO-4000-1 - Passenger car tyres and rims
- BS-ISO-4000-2 - Passenger car tyres and rims
- BS-ISO-4000-2-TC - Tracked Changes. Passenger car tyres and rims
- BS-ISO-4107 - Commercial vehicles. Wheel-hub attachment dimensions
- BS-ISO-4107-TC - Tracked Changes. Commercial vehicles. Wheel-hub attachment dimensions
- BS-ISO-4209-2 - Truck and bus tyres and rims (metric series)
- BS-ISO-7141 - Road vehicles. Light alloy wheels. Impact test
- BS-ISO-7141-TC - Tracked Changes. Road vehicles. Light alloy wheels. Lateral impact test
- BS-ISO-9413 - Tyre valves. Dimensions and designation
- CWA-14243 - Post-Consumer Tyre Materials & Applications
- PD-ISO-29846 - Tyres, valves and tubes. kPa/psi equivalencies for inflation pressures
ISO:
- ISO-10597 - Road vehicles - Flat attachment fixing nuts for commercial vehicles - Test methods
- ISO-11425 - Rubber hoses and hose assemblies for automobile power-steering systems - Specification
- ISO-12104 - Road vehicles - Gearshift patterns - Manual transmissions with power-assisted gearchange and automatic transmissions with manual-gearshift mode
- ISO-12667 - Commercial vehicles and buses - Cross-tooth propeller shaft flanges, type T
- ISO-13988 - Passenger car and light truck vehicle wheels - Clip and adhesive balance weight and rim flange nomenclature, test procedures and performance requirements
- ISO-14400 - Road vehicles - Wheels and rims - Use, general maintenance and safety requirements and out-of-service conditions
- ISO-15172 - Road vehicles - Wheels - Nut seat strength tests
- ISO-16833 - Road vehicles - Wheels - Measurement of radial and lateral run-out
- ISO-3006 - Road vehicles - Passenger car wheels for road use - Test methods
- ISO-3894 - Road vehicles - Wheels/rims for commercial vehicles - Test methods
- ISO-3911 - Wheels and rims for pneumatic tyres - Vocabulary, designation and marking
- ISO-4000-2 - Passenger car tyres and rims - Part 2: Rims
- ISO-4107 - Commercial vehicles - Wheel-hub attachment dimensions
- ISO-4209-2 - Truck and bus tyres and rims (metric series) - Part 2: Rims
- ISO-7141 - Road vehicles - Light alloy wheels - Lateral impact test
- ISO-7575 - Commercial road vehicles - Flat attachment wheel fixing nuts
- ISO-7646 - Commercial vehicles and buses - Gearbox flanges - Type A
- ISO-7647 - Commercial vehicles and buses - Gearbox flanges - Type S
- ISO-7649 - Clutch housings for reciprocating internal combustion engines - Nominal dimensions and tolerances
- ISO-7653 - Road vehicles - Commercial vehicles - Couplings between power take-offs (PTO) and ancillary driven units
- ISO-7707 - Commercial road vehicles - Connections for rear-mounted power take-offs (PTO)
- ISO-7803 - Commercial road vehicles - Steering ball joints
- ISO-7804 - Commercial road vehicles - Side openings for truck power take-offs
- ISO-8667 - Commercial vehicles and buses - Cross-tooth gearbox flanges, type T
Other SDOs:
- JIS-D-0012 - Road vehicle -- Transmission sift positions
- JIS-D-4103 - Automobile parts -- Wheels -- Performance requirements and marking
- SIS-ISO/TS-12104 - Road vehicles - Gearshift patterns - Manual transmissions with power-assisted gearchange and automatic transmissions with manual-gearshift mode
- SMS-ISO-3006 - Passenger car road wheels - Test methods
- SMS-ISO-4570-1 - Tyre valve threads - Part 1: Threads 5V1, 5V2, 6V1 and 8V1
- SS-ISO-11425 - Rubber hoses and hose assemblies for automobile power-steering systems - Specification (ISO 11425:2018, IDT)
- SS-ISO-12667 - Commercial vehicles and buses - Cross-tooth propeller shaft flanges, type T
- SS-ISO-16833 - Road vehicles - Wheels - Measurement of radial and lateral run-out (ISO 16833:2006, IDT)
- SS-ISO-3006 - Road vehicles - Passenger car wheels for road use - Test methods (ISO 3006:2005, IDT)
- SS-ISO-3894 - Road vehicles - Wheels/rims for commercial vehicles - Test methods (ISO 3894:2005, IDT)
- SS-ISO-4000-2 - Passenger car tyres and rims - Part 2: Rims (ISO 4000-2:2013, IDT)
- SS-ISO-4209-1 - Truck and bus tyres and rims (metric series) - Part 1: Tyres
- SS-ISO-4209-2 - Truck and bus tyres and rims (metric series) - Part 2: Rims (ISO 4209-2:2020, IDT)
- SS-ISO-4251-3 - Tyres (ply rating marked series) and rims for agricultural tractors and machines - Part 3: Rims (ISO 4251-3:2006, IDT)
- SS-ISO-4570-2 - Tyre valve threads - Part 2: Threads 9V1, 10V2, 12V1, 13V1
- SS-ISO-4570-3 - Tyre valve threads - Part 3, Threads 8V2, 10V1, 11V1, 13V2, 15V1, 16V1, 17V1, 17V2, 17V3, 19V1, 20V1
- SS-ISO-7575 - Commercial road vehicles - Flat attachment wheel fixing nuts
- SS-ISO-7646 - Commercial vehicles and buses - Gearbox flanges -Type A
- SS-ISO-7647 - Commercial vehicles and buses - Gearbox flanges -Type S
- SS-ISO-7653 - Road vehicles - Commercial vehicles - Couplings between power take-offs (PTO) and ancillary driven units
- SS-ISO-7706 - Road vehicles - Commercial vehicles - Clearance envelope for power take-offs (PTO)
- SS-ISO-7707 - Commercial road vehicles - Connections for rear-mounted power take-offs (PTO)
- SS-ISO-7804 - Commercial road vehicles - Side openings for truck power take-offs
- SS-ISO-8644 - Motorcycles - Light alloy wheels - Test method
- SS-ISO-8645 - Mopeds - Light alloy wheels - Test method
- SS-ISO-8720 - Passenger cars - Specifications for mechanical jacks