ASTM-B152 › Historical Revision Information
Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
The following bibliographic material is provided to assist you with your purchasing decision:
This standard covers the requirements for copper sheet, strip, plate, and rolled bar produced from copper with the following UNS Nos.; C10100, C10200, C10300, C10400, C10500, C10700, C10800, C10910, C11000, C11300, C11400, C11600, C12000, C12200, C12300, C14200, C14420, and C14530. Chemical composition shall conform to the chemical requirements pertaining to the materials UNS No. Tempering of materials shall be done by hot-rolling, cold rolling, and annealing. Copper material shall meet the maximum limit of electrical resistivity as indicated. The material shall undergo tensile strength, Rockwell hardness, and plate item tests to conform with the mechanical proptery requirement of the specification. The material shall also be capable of passing microscopical examination and embrittlement test, but not required by the specification.
Scope
1.1 This specification establishes the requirements for copper sheet, strip, plate, and rolled bar produced from the following coppers.
1.1.1 When a specific copper is not identified in the contract or purchase order, the supplier may furnish product from any of the listed coppers.
1.2 The values stated in inch-pound or SI units are to be regarded separately as standard. The values in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
1.3 The following safety hazards caveat only pertains to the test method portion, Section 13 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Keywords
annealed; copper bars; copper plate; copper sheet; copper strip ; hot-rolled; rolled; UNS No. C10100; UNS No. C10200; UNS No. C10300; UNS No. C10400; UNS No. C10500; UNS No. C10700; UNS No. C10800; UNS No. C10910; UNS No. C11000; UNS No. C11300; UNS No. C11400; UNS No. C11600; UNS No. C12000; UNS No. C12200; UNS No. C12300; UNS No. C14200; UNS No. C14420; UNS No. C14530; Bars (rolled copper); Copper alloy plate/sheet/strip/rolled bar--specifications; Plate (copper); Strip (copper); UNS C10100 (oxygen-free copper); UNS C10200 (oxygen-free copper (OF)); UNS C10300 (oxygen-free extra low phosphorus copper (OFXLP)); UNS C10400 (oxygen-free copper with silver, OFS); UNS C10500 (oxygen-free copper with silver, OFS); UNS C10700 (oxygen-free copper with silver, OFS); UNS C10800 (oxygen-free low phosphorus copper (OFLP)); UNS C10910 (copper (controlled oxygen)); UNS C11000 (electrolytic tough pitch coper (ETP)); UNS C11300 (silver-bearing tough pitch, STP); UNS C11400 (silver-bearing tough pitch, STP); UNS C11600 (silver-bearing tough pitch, STP); UNS C12000 (phosphorus deoxidized, low residual phosphorus copper (DLP)); UNS C12200 (phosphorus deoxidized, high residual phosphorus copper (DHP)); UNS C12300 (silver-bearing, high residual phosphorus copper); UNS C12500 (fire-refined tough pitch copper, FRTP); UNS C14200 (phosphorus deoxidized copper, arsenical (DPA)); UNS C14420 (copper-tellurium-tin alloy); UNS C14530 (copper-tellurium alloy); ICS Number Code 77.150.30 (Copper products)
To find similar documents by ASTM Volume:
02.01 (Copper and Copper Alloys)
To find similar documents by classification:
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Document Number
ASTM-B152/B152M-06ae1
Revision Level
2006A(E1) EDITION
Status
Superseded
Modification Type
Editorially changed
Publication Date
Feb. 1, 2008
Document Type
Specification
Page Count
7 pages
Committee Number
B05.01