ASTM-B161 › Historical Revision Information
Standard Specification for Nickel Seamless Pipe and Tube
The following bibliographic material is provided to assist you with your purchasing decision:
This specification covers the standard requirements for nickel (UNS N02200) and low-carbon nickel (UNS N02201) in the form of cold-worked seamless pipe and tube. The material shall conform to the specified chemical composition limits for nickel, copper, iron, manganese, carbon, silicon, and sulfur which shall be determined by chemical analysis. Tension test shall be performed; wherein, the tensile properties for the material specified as small-diameter and light-wall tube shall be in conformity with the tensile strength, yield strength, and elongation requirements. Each pipe or tube shall also be subjected to nondestructive electric test or hydrostatic test in accordance with a referenced ASTM document to determine the allowable fiber stress for the annealed and stress-relieved materials.
Scope
1.1 This specification covers nickel (UNS N02200)* and low-carbon nickel (UNS N02201)* in the form of cold-worked seamless pipe and tube in the conditions shown in Table 1 and Table X1.1.
1.1.1 Hot-worked material is available. Properties are to be agreed upon between the manufacturer and purchaser.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations.
TABLE 1 Mechanical Properties
Condition and Size | Tensile Strength, min, psi (MPa) | Yield Strength (0.2 % offset), min, psi (MPa) | Elongation in 2 in. or 50 mm (or 4 D), min, % | |||
---|---|---|---|---|---|---|
Nickel (UNS N02200) | Low-Carbon Nickel (UNS N02201) | Nickel (UNS N02200) | Low-Carbon Nickel (UNS N02201) | Nickel (UNS N02200) | Low-Carbon Nickel (UNS N02201) | |
Annealed: | ||||||
5 in. (127 mm) and under outside diameter | 55 000 (380) | 50 000 (345) | 15 000 (105) | 12 000 (80) | 35 | 35 |
Over 5 in. (127 mm) in outside diameter | 55 000 (380) | 50 000 (345) | 12 000 (80) | 10 000 (70) | 40 | 40 |
Stress-Relieved: | ||||||
All sizes | 65 000 (450) | 60 000 (415) | 40 000 (275) | 30 000 (205) | 15 | 15 |
Keywords
seamless pipe; seamless tube; N02200; N02201; Nickel alloy pipe--specifications; Nickel alloy tube--specifications; Seamless Ni alloy pipe--specifications; Seamless Ni alloy tube--specifications; UNS N02200 (commercially pure Ni alloy, Nickel 200); UNS N02201 (commercially pure Ni alloy, Nickel 201); Nickel alloy pipe--specifications; Nickel alloy tube--specifications; Seamless Ni alloy pipe--specifications; Seamless Ni alloy tube--specifications; UNS N02200 (commercially pure Ni alloy, Nickel 200); UNS N02201 (commercially pure Ni alloy, Nickel 201); ICS Number Code 77.150.40 (Nickel and chromium products)
To find similar documents by ASTM Volume:
To find similar documents by classification:
77.150.40 (Nickel and chromium products)
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Document Number
ASTM-B161-05(2009)
Revision Level
2005 R09 EDITION
Status
Superseded
Modification Type
Reapproval
Publication Date
Oct. 1, 2009
Document Type
Specification
Page Count
4 pages
Committee Number
B02.07