ASTM-B221 › Historical Revision Information
Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
The following bibliographic material is provided to assist you with your purchasing decision:
This specification covers extruded bars, rods, wires, profiles, and tubes made from aluminum and aluminum alloys. All the products should be produced by hot extrusion or similar methods. The chemical composition of each material is determined in accordance with the specified suitable chemical and spectrochemical test methods. Samples for chemical analysis should be taken when the ingots are poured or from the finished or semi-finished products by drilling, sawing, milling, turning, or clipping. Tensile properties, elongation, and yield strengths of each product should conform to the requirements listed herein. Elongation requirements are not applicable for materials with sizes smaller than the specified limits.
Scope
1.1 This specification covers aluminum and aluminum-alloy extruded bars, rods, wire, profiles, and tubes in the aluminum alloys (Note 1) and tempers shown in Table 2.
Note 1—Throughout this specification, the use of the term alloy in the general sense includes aluminum as well as aluminum alloy.
Note 2—For rolled or cold-finished bar and rod refer to Specification B211, for drawn seamless tube used in pressure applications, Specification B210, for structural pipe and tube, Specification B429/B429M, and for seamless pipe and tube used in pressure applications, Specification B241/B241M.
Note 3—Structural pipe and tube produced in accordance with B221 is not intended for fluid-carrying applications involving pressure. Refer to either Specification B210 or B241/B241M, as appropriate, for seamless pipe and tube used in fluid-carrying applications involving pressure.
1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9; for example, A91100 for Aluminum 1100 in accordance with Practice E527.
1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.
1.4 A complete metric companion to B221 has been developed
TABLE 1 Chemical Composition Limits A,B,C
Note—In case of a discrepancy between the values listed in Table 2 and those listed in the “International Alloy Designations and Chemical Composition Limits for Wrought Aluminum and Wrought Aluminum Alloys” (known as the “Teal Sheets”), the composition limits registered with the Aluminum Association and published in the “Teal Sheets” should be considered the controlling composition. The “Teal Sheets” are available at http://www.aluminum.org/tealsheets.
Alloy | Silicon | Iron | Copper | Manga- nese | Magne- sium | Chromium | Zinc | Titanium | Vanadium | Other ElementsD | Aluminum | |
---|---|---|---|---|---|---|---|---|---|---|---|---|
Each | TotalE | |||||||||||
1060 | 0.25 | 0.35 | 0.05 | 0.03 | 0.03 | ... | 0.05 | 0.03 | 0.05 | 0.03 | ... | 99.60 minF |
1100 | 0.95 Si + Fe | 0.05–0.20 | 0.05 | ... | ... | 0.10 | ... | ... | 0.05G | 0.15 | 99.00 minF | |
2014 | 0.50–1.2 | 0.7 | 3.9–5.0 | 0.40–1.2 | 0.20–0.8 | 0.10 | 0.25 | 0.15H | ... | 0.05H | 0.15 | remainder |
2024 | 0.50 | 0.50 | 3.8–4.9 | 0.30–0.9 | 1.2–1.8 | 0.10 | 0.25 | 0.15H | ... | 0.05H | 0.15 | remainder |
2219 | 0.20 | 0.30 | 5.8–6.8 | 0.20–0.40 | 0.02 | ... | 0.10 | 0.02–0.10 | 0.05–0.15 | 0.05I | 0.15I | remainder |
3003 | 0.6 | 0.7 | 0.05–0.20 | 1.0–1.5 | ... | ... | 0.10 | ... | ... | 0.05 | 0.15 | remainder |
Alclad 3003 | ... | 3003 Clad with 7072 alloy | ... | ... | ... | ... | ... | ... | ... | ... | ||
3004 | 0.30 | 0.7 | 0.25 | 1.0–1.5 | 0.8–1.3 | ... | 0.25 | ... | ... | 0.05 | 0.15 | remainder |
3102 | 0.40 | 0.7 | 0.10 | 0.05–0.40 | ... | ... | 0.30 | 0.10 | ... | 0.05 | 0.15 | remainder |
5052 | 0.25 | 0.40 | 0.10 | 0.10 | 2.2–2.8 | 0.15–0.35 | 0.10 | ... | ... | 0.05 | 0.15 | remainder |
5083 | 0.40 | 0.40 | 0.10 | 0.40–1.0 | 4.0–4.9 | 0.05–0.25 | 0.25 | 0.15 | ... | 0.05 | 0.15 | remainder |
5086 | 0.40 | 0.50 | 0.10 | 0.20–0.7 | 3.5–4.5 | 0.05–0.25 | 0.25 | 0.15 | ... | 0.05 | 0.15 | remainder |
5154 | 0.25 | 0.40 | 0.10 | 0.10 | 3.1–3.9 | 0.15–0.35 | 0.20 | 0.20 | ... | 0.05G | 0.15 | remainder |
5454 | 0.25 | 0.40 | 0.10 | 0.50–1.0 | 2.4–3.0 | 0.05–0.20 | 0.25 | 0.20 | ... | 0.05 | 0.15 | remainder |
5456 | 0.25 | 0.40 | 0.10 | 0.50–1.0 | 4.7–5.5 | 0.05–0.20 | 0.25 | 0.20 | ... | 0.05 | 0.15 | remainder |
6005 | 0.6–0.9 | 0.35 | 0.10 | 0.10 | 0.40–0.6 | 0.10 | 0.10 | 0.10 | ... | 0.05 | 0.15 | remainder |
6005A | 0.50–0.9 | 0.35 | 0.30 | 0.50J | 0.40–0.7 | 0.30J | 0.20 | 0.10 | ... | 0.05 | 0.15 | remainder |
6020K | 0.40-0.9 | 0.50 | 0.30-0.9 | 0.35 | 0.6-1.2 | 0.15 | 0.20 | 0.15 | … | 0.05 | 0.15 | remainder |
6041L | 0.50-0.9 | 0.15-0.7 | 0.15-0.6 | 0.05-0.20 | 0.8-1.2 | 0.05-0.15 | 0.25 | 0.15 | … | 0.05 | 0.15 | remainder |
6042M | 0.50-1.2 | 0.7 | 0.20-0.6 | 0.40 | 0.7-1.2 | 0.04-0.35 | 0.25 | 0.15 | … | 0.05 | 0.15 | remainder |
6060 | 0.30–0.6 | 0.10–0.30 | 0.10 | 0.10 | 0.35–0.6 | 0.5 | 0.15 | 0.10 | ... | 0.05 | 0.15 | remainder |
6061N | 0.40–0.8 | 0.7 | 0.15–0.40 | 0.15 | 0.8–1.2 | 0.04–0.35 | 0.25 | 0.15 | ... | 0.05 | 0.15 | remainder |
6063 | 0.20–0.6 | 0.35 | 0.10 | 0.10 | 0.45–0.9 | 0.10 | 0.10 | 0.10 | ... | 0.05 | 0.15 | remainder |
6064O | 0.40-0.8 | 0.7 | 0.15-0.40 | 0.15 | 0.8-1.2 | 0.05-0.14 | 0.25 | 0.15 | … | 0.05 | 0.15 | remainder |
6066 | 0.9–1.8 | 0.50 | 0.7–1.2 | 0.6–1.1 | 0.8–1.4 | 0.40 | 0.25 | 0.20 | ... | 0.05 | 0.15 | remainder |
6070 | 1.0–1.7 | 0.50 | 0.15–0.40 | 0.40–1.0 | 0.50–1.2 | 0.10 | 0.25 | 0.15 | ... | 0.05 | 0.15 | remainder |
6082 | 0.7–1.3 | 0.50 | 0.10 | 0.40–1.0 | 0.6–1.2 | 0.25 | 0.20 | 0.10 | ... | 0.05 | 0.15 | remainder |
6105 | 0.6–1.0 | 0.35 | 0.10 | 0.15 | 0.45–0.8 | 0.10 | 0.10 | 0.10 | ... | 0.05 | 0.15 | remainder |
6162 | 0.40–0.8 | 0.50 | 0.20 | 0.10 | 0.7–1.1 | 0.10 | 0.25 | 0.10 | ... | 0.05 | 0.15 | remainder |
6262 | 0.40–0.8 | 0.7 | 0.15–0.40 | 0.15 | 0.8–1.2 | 0.04–0.14 | 0.25 | 0.15 | ... | 0.05P | 0.15P | remainder |
6351 | 0.7–1.3 | 0.50 | 0.10 | 0.40–0.8 | 0.40–0.8 | ... | 0.20 | 0.20 | ... | 0.05 | 0.15 | remainder |
6360 | 0.35-0.8 | 0.10-0.30 | 0.15 | 0.02-0.15 | 0.25-0.45 | 0.05 | 0.10 | 0.10 | ... | 0.05 | 0.15 | remainder |
6463 | 0.20–0.6 | 0.15 | 0.20 | 0.05 | 0.45–0.9 | ... | 0.05 | ... | ... | 0.05 | 0.15 | remainder |
6560 | 0.30–0.7 | 0.10–0.30 | 0.05–0.20 | 0.20 | 0.20–0.6 | 0.05 | 0.15 | 0.10 | ... | 0.05 | 0.15 | remainder |
7005 | 0.35 | 0.40 | 0.10 | 0.20–0.7 | 1.0–1.8 | 0.06–0.20 | 4.0–5.0 | 0.01–0.06 | ... | 0.05Q | 0.15Q | remainder |
7072R | 0.7 Si + Fe | 0.10 | 0.10 | 0.10 | ... | 0.8–1.3 | ... | ... | remainder | |||
7075 | 0.40 | 0.50 | 1.2–2.0 | 0.30 | 2.1–2.9 | 0.18–0.28 | 5.1–6.1 | 0.20S | ... | 0.05S | 0.15 | remainder |
7116 | 0.15 | 0.30 | 0.50–1.1 | 0.05 | 0.8–1.4 | ... | 4.2–5.2 | 0.05 | 0.05 | 0.05T | 0.15 | remainder |
7129 | 0.15 | 0.30 | 0.50–0.9 | 0.10 | 1.3–2.0 | 0.10 | 4.2–5.2 | 0.05 | 0.05 | 0.05T | 0.15 | remainder |
7178 | 0.40 | 0.50 | 1.6–2.4 | 0.30 | 2.4–3.1 | 0.18–0.28 | 6.3–7.3 | 0.20 | ... | 0.05 | 0.15 | remainder |
A Limits are in weight percent maximum unless shown as a range, or stated otherwise.
B Analysis shall be made for the elements for which limits are shown in this table.
C For the purpose of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of the figures used in expressing the specified limit, in accordance with the rounding-off method of Practice E29.
D Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic Others elements. Should any analysis by the producer or the purchaser establish that an Others element exceeds the limit of Each or that the aggregate of several Others elements exceeds the limit of Total, the material shall be considered nonconforming.
E Other Elements
F The aluminum content shall be calculated by subtracting from 100.00 % the sum of all metallic elements present in amounts of 0.010 % or more each, rounded to the second decimal before determining the sum.
G Be 0.0003 max for welding electrode, welding rod, and filler wire.
H Upon agreement between the purchaser and the producer or supplier, a Zr + Ti limit of 0.20 % max is permitted. Properties in Specification (Table 2) are not based on the Zirconium and Titanium algorithm.
I Zirconium, 0.10–0.25 %. The total for other elements does not include zirconium.
J Manganese plus chromium shall total 0.12–0.50.
K Lead 0.05 % max, Tin 0.9-1.5 %.
L Bismuth 0.30-0.9 %, Tin 0.35-1.2 %.
M Bismuth 0.20-0.8 % Lead 0.15-0.40 %.
N In 1965 the requirements for 6062 were combined with those for 6061 by revising the minimum chromium from “0.15 %” to“ 0.04 %.” This action cancelled alloy 6062.
O Bismuth 0.50-0.7 %, Lead 0.20-0.40 %,
P Bismuth and lead shall be 0.40–0.7 % each.
Q Zirconium 0.08–0.20 %. The total for other elements does not include zirconium.
R Composition of cladding alloy applied during the course of manufacture. Samples from finished tube shall not be required to conform to these limits.
S Upon agreement between the purchaser and the producer or supplier, a Zr + Ti limit of 0.25 % max is permitted. Properties in Specification (Table 2) are not based on the Zirconium and Titanium algorithm.
T Gallium 0.03 % max.
TABLE 2 Mechanical Property LimitsA,B
Note—Strength values shown in parentheses are for information only.
Temper | Specified Section or Wall Thickness, in. | Area, in.2 | Tensile Strength, ksi | Yield Strength (0.2 % offset), ksi | Elongation in 2 in. or 4 × Diameter, min, %C | |||||
---|---|---|---|---|---|---|---|---|---|---|
min | max | min | max | |||||||
Aluminum 1060D | ||||||||||
O | all | all | 8.5 | 14.0 | 2.5 | . . . | 25 | |||
H112 | all | all | 8.5 | . . . | 2.5 | . . . | 25 | |||
Aluminum 1100D | ||||||||||
O | all | all | 11.0 | 15.5 | 3.0 | . . . | 25 | |||
H112 | all | all | 11.0 | . . . | 3.0 | . . . | 25 | |||
Alloy 2014D | ||||||||||
O | all | all | . . . | 30.0 | . . . | 18.0 | 12 | |||
T4 | ||||||||||
T4510E | all | all | 50.0 | . . . | 35.0 | . . . | 12 | |||
T4511E | ||||||||||
T42F | all | all | 50.0 | . . . | 29.0 | . . . | 12 | |||
T6 | up through 0.499 | all | 60.0 | . . . | 53.0 | . . . | 7 | |||
T6510E | 0.500–0.749 | all | 64.0 | . . . | 58.0 | . . . | 7 | |||
T6511E | up through 25 | 68.0 | . . . | 60.0 | . . . | 7 | ||||
0.750 and over | over 25 through 32 | 68.0 | . . . | 58.0 | . . . | 6 | ||||
up through 0.749 | all | 60.0 | . . . | 53.0 | . . . | 7 | ||||
T62F | up through 25 | 60.0 | . . . | 53.0 | . . . | 7 | ||||
0.750 and over | ||||||||||
over 25 through 32 | 60.0 | . . . | 53.0 | . . . | 6 | |||||
Alloy 2024D | ||||||||||
O | all | all | . . . | 35.0 | . . . | 19.0 | 12 | |||
up through 0.249 | all | 57.0 | . . . | 42.0 | . . . | 12G | ||||
T3 | 0.250–0.749 | all | 60.0 | . . . | 44.0 | . . . | 12G | |||
T3510E | 0.750–1.499 | all | 65.0 | . . . | 46.0 | . . . | 10 | |||
T3511E | up through 25 | 70.0 | . . . | 52.0H | . . . | 10 | ||||
1.500 and over | over 25 through 32 | 68.0 | . . . | 48.0I | . . . | 8 | ||||
up through 0.749 | all | 57.0 | . . . | 38.0 | . . . | 12 | ||||
0.750–1.499 | all | 57.0 | . . . | 38.0 | . . . | 10 | ||||
T42F | 1.500 and over | up through 25 | 57.0 | . . . | 38.0 | . . . | 10 | |||
over 25 through 32 | 57.0 | . . . | 38.0 | . . . | 8 | |||||
T81 | 0.050–0.249 | all | 64.0 | . . . | 56.0 | . . . | 4 | |||
T8510E | 0.250–1.499 | all | 66.0 | . . . | 58.0 | . . . | 5 | |||
T8511E | 1.500 and over | up through 32 | 66.0 | . . . | 58.0 | . . . | 5 | |||
Alloy 2219D | ||||||||||
O | all | all | . . . | 32.0 | . . . | 18.0 | 12 | |||
T31 | ||||||||||
T3510E | up through 0.499 | up through 25 | 42.0 | . . . | 26.0 | . . . | 14 | |||
T3511E | 0.500–2.999 | up through 25 | 45.0 | . . . | 27.0 | . . . | 14 | |||
T62F | up through 0.999 | up through 25 | 54.0 | . . . | 36.0 | . . . | 6 | |||
1.000 and over | up through 25 | 54.0 | . . . | 36.0 | . . . | 6 | ||||
T81 | ||||||||||
T8510E | up through 2.999 | up through 25 | 58.0 | . . . | 42.0 | . . . | 6 | |||
T8511E | ||||||||||
Alloy 3003D | ||||||||||
O | all | all | 14.0 | 19.0 | 5.0 | . . . | 25 | |||
H112 | all | all | 14.0 | . . . | 5.0 | . . . | 25 | |||
Alloy Alclad 3003D | ||||||||||
O | all | all | 13.0 | 18.0 | 4.5 | . . . | 25 | |||
H112 | all | all | 13.0 | . . . | 4.5J | . . . | 25 | |||
Alloy 3004D | ||||||||||
O | all | all | 23.0 | 29.0 | 8.5 | . . . | . . . | |||
Alloy 3102 | ||||||||||
H112K | 0.028–0.050 | all | 11.0 | 18.0 | 4.0 | . . . | 25 | |||
Alloy 5052 | ||||||||||
O | all | all | 25.0 | 35.0 | 10.0 | . . . | . . . | |||
Alloy 5083D | ||||||||||
O | up through 5.000L | up through 32 | 39.0 | 51.0 | 16.0 | . . . | 14 | |||
H111 | up through 5.000L | up through 32 | 40.0 | . . . | 24.0 | . . . | 12 | |||
H112 | up through 5.000L | up through 32 | 39.0 | . . . | 16.0 | . . . | 12 | |||
Alloy 5086D | ||||||||||
O | up through 5.000L | up through 32 | 35.0 | 46.0 | 14.0 | . . . | 14 | |||
H111 | up through 5.000L | up through 32 | 36.0 | . . . | 21.0 | . . . | 12 | |||
H112 | up through 5.000L | up through 32 | 35.0 | . . . | 14.0 | . . . | 12 | |||
Alloy 5154 | ||||||||||
O | all | all | 30.0 | 41.0 | 11.0 | . . . | . . . | |||
H112 | all | all | 30.0 | . . . | 11.0 | . . . | . . . | |||
Alloy 5454D | ||||||||||
O | up through 5.000L | up through 32 | 31.0 | 41.0 | 12.0 | . . . | 14 | |||
H111 | up through 5.000L | up through 32 | 33.0 | . . . | 19.0 | . . . | 12 | |||
H112 | up through 5.000L | up through 32 | 31.0 | . . . | 12.0 | . . . | 12 | |||
Alloy 5456D | ||||||||||
O | up through 5.000L | up through 32 | 41.0 | 53.0 | 19.0 | . . . | 14 | |||
H111 | up through 5.000L | up through 32 | 42.0 | . . . | 26.0 | . . . | 12 | |||
H112 | up through 5.000L | up through 32 | 41.0 | . . . | 19.0 | . . . | 12 | |||
Alloy 6005 | ||||||||||
T1 | up through 0.500 | all | 25.0 | . . . | 15.0 | . . . | 16 | |||
T5 | up through 0.124 | all | 38.0 | . . . | 35.0 | . . . | 8 | |||
0.125–1.000 | all | 38.0 | . . . | 35.0 | . . . | 10 | ||||
Alloy 6005A | ||||||||||
T1 | up through 0.249 | all | 25.0 | . . . | 14.5 | . . . | 15 | |||
T5 | up through 0.249 | all | 38.0 | . . . | 31.0 | . . . | 7 | |||
0.250–0.999 | all | 38.0 | . . . | 31.0 | . . . | 9 | ||||
T61 | up through 0.249 | all | 38.0 | . . . | 35.0 | . . . | 8 | |||
0.250–0.999 | all | 38.0 | . . . | 35.0 | . . . | 10 | ||||
Alloy 6020 | ||||||||||
T6511 | 3.250-6.000 | all | 38.0 | . . . | 35.0 | . . . | 10 | |||
Alloy 6041 | ||||||||||
T6M | 0.400-2.000 | all | 45.0 | . . . | 40.0 | . . . | 10 | |||
T6511M | 0.400-2.000 | all | 45.0 | . . . | 40.0 | . . . | 10 | |||
Alloy 6042 | ||||||||||
T5 | 0.400-0.499 | all | 38.0 | . . . | 35.0 | . . . | 10 | |||
0.500-1.800 | all | 42.0 | . . . | 35.0 | . . . | 10 | ||||
T5511 | 0.400-0.499 | all | 38.0 | . . . | 35.0 | . . . | 10 | |||
0.500-1.800 | all | 42.0 | . . . | 35.0 | . . . | 10 | ||||
Alloy 6060 | ||||||||||
T51 | up through 0.125 | all | 22.0 | . . . | 16.0 | . . . | 8 | |||
T61 | up through 0.124 0.125–1.000 | 30.0 30.0 | ... ... | 25.0 25.0 | ... ... | 8 10 | ||||
Alloy 6061D | ||||||||||
O | all | all | . . . | 22.0 | . . . | 16.0 | 16 | |||
T1 | up through 0.625 | all | 26.0 | . . . | 14.0 | . . . | 16 | |||
T4 | ||||||||||
T4510E | all | all | 26.0 | . . . | 16.0 | . . . | 16 | |||
T4511E | ||||||||||
T42F | all | all | 26.0 | . . . | 12.0 | . . . | 16 | |||
T51 | up through 0.625 | all | 35.0 | . . . | 30.0 | . . . | 8 | |||
T6, T62F | ||||||||||
T6510E | up through 0.249 | all | 38.0 | . . . | 35.0 | . . . | 8 | |||
T6511E | 0.250 and over | all | 38.0 | . . . | 35.0 | . . . | 10 | |||
Alloy 6063 | ||||||||||
O | all | all | . . . | 19.0 | . . . | . . . | 18 | |||
T1 | up through 0.500 | all | 17.0 | . . . | 9.0 | . . . | 12 | |||
0.501–1.000 | all | 16.0 | . . . | 8.0 | . . . | 12 | ||||
T4, T42F | up through 0.500 | all | 19.0 | . . . | 10.0 | . . . | 14 | |||
0.501–1.000 | all | 18.0 | . . . | 9.0 | . . . | 14 | ||||
T5 | up through 0.500 | all | 22.0 | . . . | 16.0 | . . . | 8 | |||
0.501–1.000 | all | 21.0 | . . . | 15.0 | . . . | 8 | ||||
T52 | up through 1.000 | all | 22.0 | 30.0 | 16.0 | 25.0 | 8 | |||
T54 | up through 0.124 | all | 33.0 | ... | 30.0 | ... | 8 | |||
0.125–0.499 | all | 33.0 | ... | 30.0 | ... | 10 | ||||
T6, T62F | up through 0.124 | all | 30.0 | . . . | 25.0 | . . . | 8 | |||
0.125–1.000 | all | 30.0 | . . . | 25.0 | . . . | 10 | ||||
T65 | up through 0.182 | all | 36.0 | . . . | 33.0 | . . . | 8 | |||
Alloy 6064 | ||||||||||
T6M | 0.400-2.000 | all | 38.0 | . . . | 35.0 | . . . | 10 | |||
T6511M | 0.400-2.000 | all | 38.0 | . . . | 35.0 | . . . | 10 | |||
Alloy 6066 | ||||||||||
O | all | all | 29.0 | . . . | 18.0 | 16 | ||||
T4, T4510, T4511E | all | all | 40.0 | . . . | 25.0 | . . . | 14 | |||
T42F | all | all | 40.0 | . . . | 24.0 | . . . | 14 | |||
T6, T6510, T6511E | all | all | 50.0 | . . . | 45.0 | . . . | 8 | |||
T62F | all | all | 50.0 | . . . | 42.0 | . . . | 8 | |||
Alloy 6070 | ||||||||||
T6, T62 | up through 2.999 | up through 32 | 48.0 | . . . | 45.0 | . . . | 6 | |||
Alloy 6082 | ||||||||||
T6,T6511 | 0.200–0.750 | all | 45.0 | ... | 38.0 | ... | 6 | |||
0.751–6.000 | all | 45.0 | .... | 38.0 | .... | 8 | ||||
6.001–8.000 | all | 41.0 | ... | 35.0 | ... | 6 | ||||
Alloy 6105 | ||||||||||
T1 | up through 0.500 | all | 25.0 | . . . | 15.0 | . . . | 16 | |||
T5 | up through 0.124 | all | 38.0 | . . . | 35.0 | . . . | 8 | |||
0.125–1.000 | all | 38.0 | . . . | 35.0 | . . . | 10 | ||||
Alloy 6162 | ||||||||||
T5, T5510,E T5511E | up thru 1.000 | all | 37.0 | . . . | 34.0 | . . . | 7 | |||
T6, T6510,E T6511E | up thru 0.249 | all | 38.0 | . . . | 35.0 | . . . | 8 | |||
0.250–0.499 | all | 38.0 | . . . | 35.0 | . . . | 10 | ||||
Alloy 6262 | ||||||||||
T6 | ||||||||||
T6510E T6511E | all | all | 38.0 | . . . | 35.0 | . . . | 10 | |||
Alloy 6351 | ||||||||||
T1 | up through 0.499 | up through 20 | 26.0 | . . . | 13.0 | . . . | 15 | |||
T11 | up through 0.749 | all | 26.0 | . . . | 16.0 | . . . | 16 | |||
T4 | up through 0.749 | all | 32.0 | . . . | 19.0 | . . . | 16 | |||
T5 | up through 0.249 | all | 38.0 | . . . | 35.0 | . . . | 8 | |||
0.250–1.000 | all | 38.0 | . . . | 35.0 | . . . | 10 | ||||
T51 | 0.125–1.000 | all | 36.0 | . . . | 33.0 | . . . | 10 | |||
T54 | up through 0.500 | all | 30.0 | . . . | 20.0 | . . . | 10 | |||
up through 0.124 | all | 42.0 | . . . | 37.0 | . . . | 8 | ||||
T6 | 0.125–0.749 | all | 42.0 | . . . | 37.0 | . . . | 10 | |||
Alloy 6360 | ||||||||||
T5 | up through 0.250 | all | 22.0 | . . . | 16.0 | . . . | 8 | |||
T6 | up through 0.120 | all | 30.0 | . . . | 25.0 | . . . | 8 | |||
0.121–0.250 | all | 30.0 | . . . | 25.0 | . . . | 10 | ||||
Alloy 6463 | ||||||||||
T1 | up through 0.500 | up through 20 | 17.0 | . . . | 9.0 | . . . | 12 | |||
T5 | up through 0.500 | up through 20 | 22.0 | . . . | 16.0 | . . . | 8 | |||
T6 | up through 0.124 | up through 20 | 30.0 | . . . | 25.0 | . . . | 8 | |||
0.125–0.500 | up through 20 | 30.0 | . . . | 25.0 | . . . | 10 | ||||
Alloy 6560 | ||||||||||
T5 | 0.090–0.125 | all | 22.0 | ... | 16.0 | ... | 8 | |||
T6 | 0.090–0.125 | all | 30.0 | ... | 25.0 | ... | 8 | |||
Alloy 7005 | ||||||||||
T53 | up through 0.750 | all | 50.0 | . . . | 44.0 | . . . | 10 | |||
Alloy 7075D | ||||||||||
O | all | all | . . . | 40.0 | . . . | 24.0 | 10 | |||
up through 0.249 | all | 78.0 | . . . | 70.0 | . . . | 7 | ||||
0.250–0.499 | all | 81.0 | . . . | 73.0 | . . . | 7 | ||||
T6, T62F | 0.500–1.499 | all | 81.0 | . . . | 72.0 | . . . | 7 | |||
T6510E | 1.500–2.999 | all | 81.0 | . . . | 72.0 | . . . | 7 | |||
T6511E | 3.000–4.499 | up through 20 | 81.0 | . . . | 71.0 | . . . | 7 | |||
over 20 through 32 | 78.0 | . . . | 70.0 | . . . | 6 | |||||
4.500–5.000 | up through 32 | 78.0 | . . . | 68.0 | . . . | 6 | ||||
T73 | 0.062–0.249 | up through 20 | 68.0 | . . . | 58.0 | . . . | 7 | |||
T73510E | 0.250–1.499 | up through 25 | 70.0 | . . . | 61.0 | . . . | 8 | |||
T73511E | 1.500–2.999 | up through 25 | 69.0 | . . . | 59.0 | . . . | 8 | |||
3.000–4.499 | up through 20 | 68.0 | . . . | 57.0 | . . . | 7 | ||||
over 20 through 32 | 65.0 | . . . | 55.0 | . . . | 7 | |||||
up through 0.049 | all | 73.0 | . . . | 63.0 | . . . | 7 | ||||
T76 | 0.050–0.124 | all | 74.0 | . . . | 64.0 | . . . | 7 | |||
T76510E | 0.125–0.249 | up through 20 | 74.0 | . . . | 64.0 | . . . | 7 | |||
T76511E | 0.250–0.499 | up through 20 | 75.0 | . . . | 65.0 | . . . | 7 | |||
0.500–1.000 | up through 20 | 75.0 | . . . | 65.0 | . . . | 7 | ||||
1.001–2.000 | up through 20 | 75.0 | . . . | 65.0 | . . . | 7 | ||||
2.001–3.000 | up through 20 | 74.0 | . . . | 64.0 | . . . | 7 | ||||
3.001–4.000 | up through 20 | 74.0 | . . . | 63.0 | . . . | 7 | ||||
Alloy 7116 | ||||||||||
T5 | 0.125–0.500 | all | 48.0 | . . . | 42.0 | . . . | 8 | |||
Alloy 7129 | ||||||||||
T5, T6 | up through 0.500 | all | 55.0 | . . . | 49.0 | . . . | 9 | |||
Alloy 7178D | ||||||||||
O | all | up through 32 | . . . | 40.0 | . . . | 24.0 | 10 | |||
up through 0.061 | up through 20 | 82.0 | . . . | 76.0 | . . . | . . . | ||||
0.062–0.249 | up through 20 | 84.0 | . . . | 76.0 | . . . | 5 | ||||
T6 | 0.250–1.499 | up through 25 | 87.0 | . . . | 78.0 | . . . | 5 | |||
T6510E | 1.500–2.499 | up through 25 | 86.0 | . . . | 77.0 | . . . | 5 | |||
T6511E | over 25 through 32 | 84.0 | . . . | 75.0 | . . . | 5 | ||||
2.500–2.999 | up through 32 | 82.0 | . . . | 71.0 | . . . | 5 | ||||
up through 0.061 | up through 20 | 79.0 | . . . | 73.0 | . . . | 5 | ||||
0.062–0.249 | up through 20 | 82.0 | . . . | 74.0 | . . . | 5 | ||||
0.250–1.499 | up through 25 | 86.0 | . . . | 77.0 | . . . | 5 | ||||
T62F | ||||||||||
1.500–2.499 | up through 25 | 86.0 | . . . | 77.0 | . . . | 5 | ||||
over 25 through 32 | 84.0 | . . . | 75.0 | . . . | 5 | |||||
2.500–2.999 | up through 32 | 82.0 | . . . | 71.0 | . . . | 5 | ||||
T76 | 0.125–0.249 | up through 20 | 76.0 | . . . | 66.0 | . . . | 7 | |||
T76510E | 0.250–0.499 | up through 20 | 77.0 | . . . | 67.0 | . . . | 7 | |||
T76511E | 0.500–1.000 | up through 20 | 77.0 | . . . | 67.0 | . . . | 7 |
A The basis for establishment of tensile property limits is shown in Annex A1.
B To determine conformance to this specification, each value shall be rounded to the nearest 0.1 ksi for strength and nearest 0.5 % for elongation in accordance with the rounding-off-method of Practice E29.
C Elongation of full-section and cut-out sheet-type specimens is measured in 2 in. Elongation of cut-out round specimens is measured in 4× specimen diameter. See 8.1.1 and 8.1.2 for conditions under which measurements are not required.
D These alloys are also produced in the F temper for which no tensile properties are specified or guaranteed.
E For stress relieved tempers (T3510, T3511, T4510, T4511, T5510, T5511, T6510, T6511, T73510, T73511, T76510, T76511, T8510, T8511), characteristics and properties other than those specified may differ somewhat from the corresponding characteristics and properties of material in the basic tempers.
F Material in the T42 and T62 tempers is not available from the material producers.
G Minimum elongation for tube, 10 %.
H Minimum yield strength for tube, 48.0 ksi.
I Minimum yield strength for tube, 46.0 ksi.
J Yield strength is not applicable in tube.
K Only in tube form.
L Properties not applicable to extruded tube over 2.999 in wall thickness.
M Tentative; properties subject to revision.
Keywords
aluminum alloy; extruded bars; extruded profiles; extruded rods; extruded tubes; extruded wire; UNS A91100 (Wr. alum. alloy); UNS A92014 (Wr. alum. alloy, heat treatable); UNS A92024 (Wr. alum. alloy, heat treatable); UNS A92219 (Wr. alum. alloy, heat treatable); UNS A93003 (Wr. alum. alloy); UNS A93004 (Wr. alum. alloy); UNS A93102 (Wr. alum. alloy); UNS A95052 (Wr. alum. alloy); UNS A95083 (Wr. alum. alloy); UNS A95086 (Wr. alum. alloy); UNS A95154 (Wr. alum. alloy); UNS A95454 (Wr. alum. alloy); UNS A95456 (Wr. alum. alloy, non-heat treatable); UNS A96005 (Wr. alum. alloy, heat treatable); UNS A96061 (Wr. alum. alloy); UNS A96063 (Wr. alum. alloy); UNS A96066 (Wr. alum. alloy, heat treatable); UNS A96105 (Wr. alum. alloy, heat treatable); UNS A96262 (Wr. alum. alloy); Aluminum--specifications; Aluminum alloys (rod)--specifications; Aluminum alloys (tube)--specifications; Aluminum alloys (wire)--specifications; Extruded bars/rods/wire; UNS A91060 (Wr. alum. alloy); UNS A96351 (Wr. alum. alloy, heat treatable); UNS A96463 (Wr. alum. alloy, heat treatable); UNS A97005 (Wr. alum. alloy, heat treatable); UNS A97075 (Wr. alum. alloy, heat treatable); UNS A97178 (Wr. alum. alloy, heat treatable); UNS A97072 (Wr. alum. alloy); ICS Number Code 77.150.10 (Aluminium products)
To find similar documents by ASTM Volume:
02.02 (Aluminum and Magnesium Alloys)
To find similar documents by classification:
77.150.10 (Aluminium products)
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Document Number
ASTM-B221-12
Revision Level
2012 EDITION
Status
Superseded
Modification Type
Revision
Publication Date
April 15, 2012
Document Type
Specification
Page Count
14 pages
Committee Number
B07.03