ASTM-B335 › Historical Revision Information
Standard Specification for Nickel-Molybdenum Alloy Rod
The following bibliographic material is provided to assist you with your purchasing decision:
This specification covers rod of nickel-molybdenum alloys of UNS N10001, N10665, N10675, N10629, and N10624 for use in general corrosive service. The material shall conform to the required chemical composition for nickel, molybdenum, iron, chromium, carbon, silicon, cobalt, manganese, phosphorus, sulfur, vanadium, nickel, molybdenum, aluminum, columbium, copper, tantalum, titanium, tungsten, zirconium, and magnesium. The alloys shall conform to the required mechanical properties such as tensile strength, yield strength, elongation, and Rockwell hardness.
Scope
1.1 This specification2 covers rod of nickel-molybdenum alloys (UNS N10001, N10665, N10675, N10629, and N10624)* as shown in Table 1, for use in general corrosive service.
Element | Composition Limits, % |
| |||
Alloy | Alloy | Alloy | Alloy | Alloy | |
Nickel | remainderA | remainderA | 65.0 min | remainderA | Bal |
Molybdenum | 26.0–30.0 | 26.0–30.0 | 27.0–32.0 | 26.0–30.0 | 21.0-25.0 |
Iron | 4.0–6.0 | 2.0 max | 1.0–3.0 | 1.0–6.0 | 5.0-8.0 |
Chromium | 1.0 max | 1.0 max | 1.0–3.0 | 0.5–1.5 | 6.0-10.0 |
Carbon, | 0.05 | 0.02 | 0.01 | 0.01 | 0.01 |
Silicon, max | 1.0 | 0.10 | 0.10 | 0.05 | 0.10 |
Cobalt, max | 2.5 | 1.00 | 3.0 | 2.5 | 1.0 |
Manganese, | 1.0 | 1.0 | 3.0 | 1.5 | 1.0 |
Phosphorus, | 0.04 | 0.04 | 0.030 | 0.04 | 0.025 |
Sulfur, max | 0.03 | 0.03 | 0.010 | 0.01 | 0.01 |
Vanadium | 0.2–0.4 | ... | 0.20 max | ... | ... |
Nickel plus | ... | ... | 94.0–98.0 |
| ... |
Aluminum | ... | ... | 0.50 max | 0.1–0.5 | 0.5 |
Columbium | ... | ... | 0.20 |
| ... |
Copper, max | ... | ... | 0.20 | 0.5 | 0.5 |
Tantalum, | ... | ... | 0.20 |
| ... |
Titanium, | ... | ... | 0.20 |
| ... |
Tungsten, | ... | ... | 3.0 |
| ... |
Zirconium, | ... | ... | 0.10 |
| ... |
Magnesium, | ... | ... | ... | ... | ... |
1.2 The following products are covered under this specification:
1.2.1 Rods 5/16 to 3/4 in. (7.94 to 19.05 mm) excl in diameter, hot or cold finished, solution annealed and pickled or mechanically descaled.
1.2.2 Rods 3/4 to 31/2 in. (19.05 to 88.9 mm) incl in diameter, hot or cold finished, solution annealed, ground or turned.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
Keywords
rod; N10001; N10624; N10629; N10665; N10675; ICS Number Code 77.150.40 (Nickel and chromium products)
To find similar documents by ASTM Volume:
To find similar documents by classification:
77.150.40 (Nickel and chromium products)
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Document Number
ASTM-B335-03(2013)
Revision Level
2003 R13 EDITION
Status
Superseded
Modification Type
Reapproval
Publication Date
Feb. 15, 2013
Document Type
Specification
Page Count
4 pages
Committee Number
B02.07