ASTM-B824 › Standard Specification for General Requirements for Copper Alloy Castings
The following bibliographic material is provided to assist you with your purchasing decision:
This specification establishes the general requirements common to copper alloy castings of UNS Nos. C94700, C95300, C95400, C95410, C95500, C95520, and C96800. Materials shall be sampled and prepared, then tested accordingly to examine their conformance to mechanical (tensile and yield strength, hardness, and elongation), electrical (resistivity and conductivity), dimensional, chemical composition, and grain size requirements. In the event of conflict between this specification and the individual casting product specifications, the requirements of the casting specification shall take precedence.
Changes from the previous issue
A redline edition is available for this document, with all changes visible. Ask Document Center Inc. for more information.
Scope
1.1 This specification establishes general requirements common to ASTM copper alloy casting specifications B22/B22M, B61, B62, B66, B67, B148, B176, B271/B271M, B369, B427, B505/B505M, B584, B763/B763M, B770, and B806. These requirements apply to the casting specifications to the extent referenced therein.
1.1.1 In the event of conflict between this specification and a casting specification, the requirements of the casting specification shall take precedence.
1.2 The chemical composition and other requirements not included in this specification shall be prescribed in the casting product specifications.
1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 No precise quantitative relationship can be stated between the properties of the metal in various locations of the same casting or between the properties of castings and those of a test bar casting from the same metal. (See Appendix X1.)2
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Significance and Use
14.1 For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.
Property | Rounded Limit for Observed or |
| |
Chemical Composition | nearest unit in the last right-hand significance digit used in expressing the limiting value |
|
|
Tensile Strength | nearest ksi (5 MPa) |
Yield Strength | |
|
|
Elongation | nearest 1 % |
|
|
Grain Size: |
|
Under 0.060 mm | nearest multiple of 0.005 mm |
0.060 mm and over | nearest 0.01 mm |
Keywords
copper alloy castings; copper-base alloy castings; UNS No. C94700; UNS No. C95300; UNS No. C95400; UNS No. C95410; UNS No. C95500; UNS No. C95520; UNS No. C96800;; ICS Number Code 77.150.30 (Copper products)
To find similar documents by ASTM Volume:
02.01 (Copper and Copper Alloys)
To find similar documents by classification:
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Customers who bought this document also bought:
ASTM-A240Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
ASQ-Z1.4
Sampling Procedures and Tables for Inspection by Attributes - Paper Format - Reaffirmed in 2018
ASTM-A484
Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings
Document Number
ASTM-B824-17
Revision Level
2017 EDITION
Status
Current
Modification Type
Revision
Publication Date
May 1, 2017
Document Type
Specification
Page Count
6 pages
Committee Number
B05.05