ASTM-F2412 › Historical Revision Information
Standard Test Methods for Foot Protection

ASTM-F2412 - 2018 EDITION - SUPERSEDED
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:

Standard Test Methods for Foot Protection
ORDER

Scope

1.1 These test methods measure the resistance of footwear to a variety of hazards that can potentially result in injury.

1.2 These test methods may be used to test for compliance to minimum performance requirements in established safety standards.

1.2.1 By agreement between the purchaser and the supplier, or as required by established safety standards, these test methods can be used to determine any one, or all of the following: (1) impact resistance (I), (2) compression resistance (C), (3) metatarsal impact resistance (Mt), (4) resistance to electrical conductivity (Cd), (5) resistance to electric hazard (EH), (6) static dissipative performance (SD), and (7) puncture resistance (PR).

1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Significance and Use

4.1 These test methods contain requirements to evaluate the performance of footwear for the following:

4.1.1 Impact resistance for the toe area of footwear (I/75),

4.1.2 Compression resistance for the toe area of footwear (C/75),

4.1.3 Metatarsal protection that reduces the chance of injury to the metatarsal bones at the top of the foot (Mt/75),

4.1.4 Conductive properties which reduce hazards that may result from static electricity buildup, and reduce the possibility of ignition of explosives and volatile chemicals (Cd),

4.1.5 Electric Hazard by stepping on live wire (EH),

4.1.6 Static dissipative (SD) properties to reduce hazards due to excessively low footwear electrical resistance that may exist where SD footwear is required, and

4.1.7 Puncture resistance footwear devices (PR).

4.2 Any changes to the original components of safety toe footwear such as replacing or adding after-market footbeds/inserts could cause non-compliance to any or all parts of this standard rendering the ASTM label invalid. Protective toe footwear specimens or samples shall be retested for any of the following changes.

4.2.1 Change in material used to make protective toe cap, change in protective cap manufacturer, change in the design of the toe cap.

4.2.2 Change in construction method used to make footwear or change in factory in which footwear is produced.

4.2.3 Change in the upper or insole material thickness greater than 25 %, change to the soling system or a change in the hardness of the outsole.

4.2.4 Change in shape of last used in the manufacturing of footwear.

4.2.5 Change in material or supplier of protective insole.

4.2.6 Change in material or supplier of met guard.

Keywords

compression resistance (C); conductive footwear (Cd); electric hazard resistance (EH); ESD safety footwear; foot protection; impact resistance (I); metatarsal protection (Mt); protective footwear; puncture resistance (PR); safety footwear; soft toe protective footwear; static dissipative (SD);; ICS Number Code 13.340.50 (Leg and foot protection)

To find similar documents by ASTM Volume:

15.07 (Sports Equipment and Facilities; Pedestrian/Walkway Safety and Footwear; Amusement Rides and Devices; Snow Skiing)

To find similar documents by classification:

13.340.50 (Leg and foot protection Including safety boots and shoes)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

Document Number

ASTM-F2412-18

Revision Level

2018 EDITION

Status

Superseded

Modification Type

Revision

Publication Date

Feb. 1, 2018

Document Type

Test Method

Page Count

19 pages

Committee Number

F13.30