ASTM-A74 › Historical Revision Information
Standard Specification for Cast Iron Soil Pipe and Fittings
The following bibliographic material is provided to assist you with your purchasing decision:
This specification covers cast gray iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. These pipe and fittings are not intended for pressure applications. The cast iron shall be produced by an established commercial method that provides control over chemical and physical properties. Castings shall be sound, true to pattern, and of compact close grain that permits drilling and cutting by ordinary methods and its interior surface shall be reasonably smooth and free from defects. Ferrous scrap, pig iron, and any recycled ferrous material to be used in the melting operation shall be screened for radioactivity. Tension test shall include breaking load, machined diameter, and tensile strength. Chemical test shall conform to the chemical composition requirements prescribed for phosphorous, sulfur, chromium, titanium, aluminum, lead, and carbon equivalent. Dimension requirements for hub, spigot, barrel, grooves, water seal and trap, and threads of the pipe and fittings are detailed. The pipe and fittings shall be uniformly coated with a material suitable for the purpose.
Scope
1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. It establishes standards covering material, manufacture, mechanical and chemical properties, coating, test methods, inspection, certification, product markings, dimensions, and dimensional tolerances for extra heavy and service cast iron soil pipe and fittings. These pipe and fittings are not intended for pressure applications as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.
1.2 This specification covers pipe and fittings of the following patterns and, when so designated, shall apply to any other patterns that conform with the applicable requirements given in this specification.
1.2.1 Pipe:
Tables | |
---|---|
Extra heavy, 2½ ft (0.75 m), 3½ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m) lengths | 1, 2 |
Service, 2½ ft (0.75 m), 3½ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m) | 1, 2 |
Outside dimensions (for detailing) | X1.1 |
1.2.2 Fittings:
Tables | |
---|---|
¼ bends; long ¼ bends | 3, 4 |
¼ bends, long low-hub | 5 |
¼ bends, low heel; high heel | 6, 7 |
¼ bends, short sweep; long sweep | 8 |
¼ bends, reducing long sweep | 9 |
1/5 bends | 10 |
1/6 bends | 10 |
1/8 bends; long 1/8 bends | 11 |
1/16 bends | 11 |
Y branches | 12, 13 |
Y branches, combination 1/8 bends, single | 14 |
Y branches, combination 1/8 bends, double | 14 |
Sanitary T branches, single | 15 |
Sanitary T branches, double | 15 |
Sanitary T branches, cleanout | 16 |
Tapped sanitary T branches, single | 17 |
Tapped sanitary T branches, double | 17 |
T branches, single and double | 18 |
Tapped T branches, single | 19 |
Tapped T branches, double | 19 |
T branches, cleanout | 20 |
-45° offset fitting | 21 |
Double hubs | 22 |
Long double hubs | 22 |
Reducers | 23 |
Increasers | 24, 25 |
P traps | 26, 27 |
Deep seal P traps | 28 |
Running traps | 29 |
Screw plugs (brass) | 30 |
Blind plugs | 31 |
Iron-body ferrules | 32 |
Side inlets | Fig. 3 |
Closet bends | 33 |
Tapping bosses | 34 |
Reducing ¼ bend SV | 35 |
Combination Y and 1/8 bend | 36 |
‘H’ branch fitting | 37 |
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Keywords
cast iron; fitting; hub and spigot pipe; pipe; soil pipe; Cast iron soil pipe/fittings--specifications; Fittings; Iron pipe/fittings--specifications; ICS Number Code 23.040.40 (Metal fittings)
To find similar documents by ASTM Volume:
01.02 (Ferrous Castings; Ferroalloys)
To find similar documents by classification:
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Document Number
ASTM-A74-08a
Revision Level
2008A EDITION
Status
Superseded
Modification Type
Revision
Publication Date
Dec. 1, 2008
Document Type
Specification
Page Count
44 pages
Committee Number
A04.12