ASTM-A907 Historical Revision Information
Standard Specification for Steel, Sheet and Strip, Heavy Thickness Coils, Carbon, Hot-Rolled, Structural Quality (Withdrawn 2001)

ASTM-A907 - 1992 R93(E1) EDITION - SUPERSEDED -- See the following: ASTM-A1018
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:

Standard Specification for Steel, Sheet and Strip, Heavy Thickness Coils, Carbon, Hot-Rolled, Structural Quality (Withdrawn 2001)


1.1 This specification covers hot-rolled heavy-thickness carbon-steel sheet and strip of structural quality in coils beyond the size limits of Specification A570/A570M. This material is intended for structural purposes where mechanical test values are required and is available in the sizes listed below. This material is available only in coils as described below:

Size Limits, Coils Only Product Width, in. (mm) Thickness, in. (mm) Strip over 8 to 12 0.230 to 0.750, incl (200 to 300) (6.0 to 19) Sheet over 12 to 48 0.230 to 0.750, incl (300 to 1200) (6.0 to 19) over 48 (1200) 0.180 to 0.750, incl (4.5 to 19)

1.1.1 The following grades are covered in this specification:

Mechanical Properties Yield Point min, Tensile Strength Grade ksi (MPa) min, ksi (MPa) 30 30 (205) 49 (340) 33 33 (230) 52 (360) 36 36 (250) 53 (365) 40 40 (275) 55 (380)

1.2 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standard. Within the text the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values of the two systems may result in nonconformance with this specification.

1.3 Sheet and strip in coils of the sizes noted in 1.1 can be included in this specification only with the following provisions:

1.3.1 The material is not to be converted into steel plates for structural or pressure vessel use unless tested in complete accordance with the appropriate sections of Specifications A6/A6M (plates provided from coils) or A20/A20M (plates produced from coils),

1.3.2 This specification is not applicable to the steels covered by Specification A635/A635M,

1.3.3 The dimensional tolerances from Specification A635/A635M are applicable to material produced in accordance with this specification,

1.3.4 The material is to be fed directly from coils into a blanking press, drawing or forming operation, tube mill, rolling mill, or sheared or slit into blanks for subsequent drawing or forming, and

1.3.5 Not all strength levels are available in all thicknesses. The user should consult the producer for appropriate size limitations.


Carbon; carbon steel sheet; carbon steel strip; heavy thickness coils; hot rolled; hot rolled steel sheet; hot rolled steel strip; sheet; steel; steel sheet; steel strip; strip; structural applications; structural quality; ICS Number Code 77.140.50 (Flat steel products and semi-products)

To find similar documents by ASTM Volume:

01.03 (Steel--Plate, Sheet, Strip, Wire; Stainless Steel Bar)

To find similar documents by classification:

77.140.50 (Flat steel products and semi-products Including plate, sheet and strip Steel strips for springs, see 77.140.25)

To find similar documents by Federal Supply Class Code:

FSC 9515 (Plate, Sheet, Strip, Foil, and Leaf)

Document Number


Revision Level

1992 R93(E1) EDITION



Modification Type


Publication Date

Sept. 1, 1993

Document Type


Page Count

3 pages

Committee Number