ASTM-B447 › Historical Revision Information
Standard Specification for Welded Copper Tube
The following bibliographic material is provided to assist you with your purchasing decision:
This specification establishes the requirements for welded copper tube with a longitudinal seam free of filler metal produced from sheet or strip of one of the Copper UNS Nos. C10100, C10200, C10300, C10800, C11000, C12000, C12200, and C14200. Copper C11000 welded tube shall not be used in applications where hydrogen embrittlement during heating is a concern. Tempers of the welded tube types are as follows: as-welded: WM50, WM02, or WM04, welded and annealed: W060 and W050, welded and cold drawn: WH00, WH02, and WH04, and fully finished: O60, O50, H55, H58, and H80. The product shall be manufactured by forming the material into a tubular shape on a suitable forming mill and welding shall be accomplished by any process that produces forge or fusion welds. The external flash of forge welded tube shall be removed by scarfing and the internal flash shall be treated by IFI (to remain in the as-welded condition), IFR (scarfing) or IFD (rolling or drawing) technique. The material shall conform to the chemical composition requirements prescribed for copper, phosphorus, and arsenic, as determined by chemical analysis. The welded tubes shall meet the requirements specified for grain size, electrical mass resistivity, mechanical properties such as tensile strength and Rockwell hardness, dimensions, and mass. Performance requirements includes microscopical examination, hydrogen embrittlement susceptibility test, and expansion test. Requirements for tensile, electromagnetic (eddy-current), hydrostatic, and pneumatic tests are detailed.
Scope
1.1 This specification establishes the requirements for welded copper tube with a longitudinal seam free of filler metal produced from sheet or strip of the following coppers:
Copper UNS Nos. | Type of Copper |
C10100 | Oxygen-free electronic |
C10200 | Oxygen-free |
C10300 | Oxygen-free, extra low phosphorus |
C10800 | Oxygen-free, low phosphorus |
C11000 | Electrolytic tough pitch |
C12000 | Phosphorus deoxidized, low residual phosphorus |
C12200 | Phosphorus deoxidized, high residual phosphorus |
C14200 | Phosphorus deoxidized, arsenical |
1.2 Unless otherwise specified in the contract or purchase order, product furnished of any listed copper, with the exception of copper C11000, shall be considered acceptable.
1.2.1 Copper C11000 welded tube shall not be used in applications where hydrogen embrittlement during heating is a concern.
1.3 Units—Values stated in inch-pound units are to be regarded as standard except for grain size, which is given in SI units. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard.
1.4 The following hazard caveat pertains only to Section 13 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Significance and Use
For purposes of determining compliance with the specified limits for requirements of the properties listed in the following table and for dimensional tolerances, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29:
Property | Rounded Unit for Observed or Calculated Value |
Chemical composition | Nearest unit in the last right-hand |
Hardness | Significant |
Electrical Resistivity | Digit used in expression the limiting value |
Grain size up to 0.055 mm, incl | nearest multiple of 0.005 mm |
Tensile strength | nearest ksi (5 MPa) |
Expansion | Nearest 1% |
Keywords
copper tube; copper welded tube; welded tube ; Copper UNS No. C10100; Copper UNS No. C10200; Copper UNS No. C10300; Copper UNS No. C10800; Copper UNS No. C11000; Copper UNS No. C12000; Copper UNS No. C12200; Copper UNS No. C14200; Copper welded tube; UNS C10100 (oxygen-free copper)--pipe/tube; UNS C10200--pipe/tube (seamless/welded); UNS C10300--pipe/tube (seamless/welded); UNS C10800--pipe/tube (seamless/welded); UNS C11000 (electrolytic tough pitch coper (ETP)); UNS C12000--pipe/tube (seamless/welded); UNS C12200--pipe/tube (seamless/welded); UNS C14200 (phosphorus deoxidized copper, arsenical (DPA)); Welded Cu/Cu alloy tube; ICS Number Code 23.040.15 (Non-ferrous metal pipes); 77.150.30 (Copper products)
To find similar documents by ASTM Volume:
02.01 (Copper and Copper Alloys)
To find similar documents by classification:
23.040.15 (Non-ferrous metal pipes Non-ferrous metal pipes and tubes for specific use, see 77.150)
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Document Number
ASTM-B447-12
Revision Level
2012 EDITION
Status
Superseded
Modification Type
Revision
Publication Date
June 15, 2012
Document Type
Specification
Page Count
9 pages
Committee Number
B05.04