ASTM-B829 › Historical Revision Information
Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube
The following bibliographic material is provided to assist you with your purchasing decision:
This general specification contains the mandatory requirements to the ASTM standards listed herein for seamless pipes and tubes made from nickel and nickel alloys. In case of conflict, the requirements listed in the particular product specification takes precedence over those listed here.
Scope
1.1 This specification contains various requirements that, with the exception of Sections 5 and 10, are mandatory requirements to the following ASTM nickel and nickel alloy, seamless pipe and tube specifications:
Title of Specification | ASTM |
Nickel Seamless Pipe and Tube | B161 |
Seamless Nickel and Nickel Alloy, Condenser and Heat Ex- | B163 |
Nickel-Copper Alloy (UNS N04400) Seamless Pipe and Tube | B165 |
Nickel-Chromium-Iron Alloys (UNS N06600, N06601, and | B167 |
Nickel-Iron-Chromium Alloy Seamless Pipe and Tube | B407 |
Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825 | B423 |
Nickel-Chromium-Molybdenum-Columbium Alloys (UNS | B444 |
Nickel-Chromium-Iron-Columbium-Molybdenum-Tungsten Alloy | B445 |
Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and UNS | B535 |
Copper-Beryllium Alloy Forgings and Extrusion | B570 |
Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube | B622 |
UNS N08028 Seamless Tubes | B668 |
UNS N08904, UNS N08925 and UNS N08926 Seamless Pipe | B677 |
Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and | B690 |
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Seamless Pipe and | B722 |
Seamless UNS N08020, UNS N08026, and UNS N08024 | B729 |
1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the purchase order.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only the requirement of the product specification needs to be satisfied.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 The following safety hazards caveat pertains only to the test requirements portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Keywords
cold worked; hot finished; nickel; nickel alloys; seamless pipe; seamless tube;; ICS Number Code 23.040.15 (Non-ferrous metal pipes)
To find similar documents by ASTM Volume:
To find similar documents by classification:
23.040.15 (Non-ferrous metal pipes Non-ferrous metal pipes and tubes for specific use, see 77.150)
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Document Number
ASTM-B829-04a(2017)
Revision Level
2004A R17 EDITION
Status
Superseded
Modification Type
Reapproval
Publication Date
April 15, 2017
Document Type
Specification
Page Count
6 pages
Committee Number
B02.07