ASTM-B860 › Historical Revision Information
Standard Specification for Zinc Master Alloys for Use in Hot Dip Galvanizing
The following bibliographic material is provided to assist you with your purchasing decision:
This specification covers electrical contact components made from copper tungsten by powder metallurgical procedures. The material shall conform to the chemical composition limits as agreed upon between the manufacturer and the user. Qualification tests for determination of physical properties shall be performed on production parts, wherever practical or applicable. The tests shall be determined after consideration of the function of the part.This specification covers zinc master alloys which are used in hot dip galvanizing for the purpose of adjusting the concentration of certain alloying elements in the molten zinc bath. The paper presented the chemical composition of these materials which include six master alloys of zinc aluminium; Type A-1, Type A-2, Type A-3, Type A-4, Type A-5, Type A-6, and one master alloy of zinc-antimony, Type S-1. The material covered by this specification shall be made of uniform quality and shall be free from harmful contamination. The alloys shall be tested and conform to the required chemical composition requirements.
Scope
1.1 This specification covers zinc master alloys which are used in hot dip galvanizing for the purpose of adjusting the concentration of certain alloying elements in the molten zinc bath. Table 1 covers the chemical composition of these materials which include six master alloys of zinc-aluminum (brightener) and one master alloy of zinc-antimony.
ASTM | Common |
| UNS |
Type A-1 | 90/10 Zn/Al | High Purity | Z30750 |
Type A-2 | 90/10 Zn/Al | Low Purity | Z31710 |
Type A-3 | 95/5 Zn/Al | High Purity | Z30503 |
Type A-4 | 95/5 Zn/Al | Low Purity | Z31510 |
Type A-5 | 96/4 Zn/Al | High Purity | Z31520 |
Type A-6 | 96/4 Zn/Al | Low Purity | Z30504 |
Type S-1 | 90/10 Zn/Sb |
| Z55710 |
TABLE 1 Chemical Requirements Composition, % (Range or Maximum Value)A
Type A-1 | 90 % Zinc–10 % Aluminum (90/10 Zn/Al) | High Purity | |||||
Type A-2 | 90 % Zinc–10 % Aluminum (90/10 Zn/Al) | Low Purity | |||||
Type A-3 | 95 % Zinc–5 % Aluminum (95/5 Zn/Al) | High Purity | |||||
Type A-4 | 95 % Zinc–5 % Aluminum (95/5 Zn/Al) | Low Purity | |||||
Type A-5 | 96 % Zinc–4 % Aluminum (96/4 Zn/Al) | High Purity | |||||
Type A-6 | 96 % Zinc–4 % Aluminum (96/4 Zn/Al) | Low Purity | |||||
Type S-1 | 90 % Zinc–10 % Antimony (90/10 Zn/Sb) |
| |||||
UNSB | Type A-1 | Type A-2 | Type A-3 | Type A-4 | Type A-5 | Type A-6 | Type S-1 |
Fe | 0.05 max | 0.15 max | 0.05 max | 0.15 max | 0.05 max | 0.15 max | 0.03 max |
Pb | 0.005 max | 0.4 max | 0.005 max | 0.4 max | 0.005 max | 0.4 max | 0.015 max |
Cd | 0.004 max | ... | 0.004 max | ... | 0.004 max | ... | 0.003 max |
Cu | 0.035 max | 0.5 max | 0.035 max | 0.5 max | 0.035 max | 0.5 max | 0.003 max |
Mg | ... | ... | ... | ... | 0.06 max | 0.06 max |
|
Sn | 0.003 max | ... | 0.003 max | ... | 0.003 max | ... | 0.01 max |
As | ... | ... | ... | ... | ... | ... | 0.015 max |
Al | 9.5–10.5 | 9.5–10.5 | 4.5–5.5 | 4.5–5.5 | 4.0-4.5 | 4.0-4.5 | ... |
SbC | ... | ... | ... | ... | ... | ... | 9.5–10.5 |
Others, Total | 0.01 max | 0.25 max | 0.01 max | 0.25 max | 0.01 max | 0.25 max | 0.03 max |
ZnD | Remainder | Remainder | Remainder | Remainder | Remainder | Remainder | Remainder |
Note 1: The master alloys in Specification B860 are intended to be used primarily in hot-dip galvanizing to adjust the concentration of certain elements in a molten zinc bath, and differ from the zinc-aluminum alloys in Specification B997 which are intended to be used primarily in molten zinc-aluminum.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health and environmental practices, and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Keywords
brightener; zinc; zinc alloys; zinc-aluminum alloy; zinc-antimony alloy; zinc master alloys; zinc metal;; ICS Number Code 77.120.60 (Lead, zinc, tin and their alloys)
To find similar documents by ASTM Volume:
To find similar documents by classification:
77.120.60 (Lead, zinc, tin and their alloys)
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Document Number
ASTM-B860-17
Revision Level
2017 EDITION
Status
Superseded
Modification Type
Revision
Publication Date
June 1, 2017
Document Type
Specification
Page Count
3 pages
Committee Number
B02.04