ASTM-D244 › Historical Revision Information
Standard Test Methods and Practices for Emulsified Asphalts
The following bibliographic material is provided to assist you with your purchasing decision:
Scope
1.1 These test methods and practices, given under the headings titled Composition, Consistency, Stability, and Examination of Residue, cover the examination of asphalt emulsions composed principally of a semisolid or liquid asphaltic base, water, and an emulsifying agent. The test methods cover the following tests and practices:
Test | Sections |
Composition: | |
Water Content | 4-10 |
Residue and Oil Distillate by Distillation | See Test Method D 6997 |
Residue by Evaporation | See Test Method D 6934 |
Particle Charge of Cationic Emulsified Asphalts | See Test Method D 7402 |
Consistency: | |
Viscosity (Saybolt Furol) | See Test Method D 7496 |
Stability: | |
Demulsibility | See Test Method D 6936 |
Settlement | See Test Method D 6930 |
Cement Mixing | See Test Method D 6935 |
Sieve Test | See Test Method D 6933 |
Aggregate Coating | See Practice D 6998 |
Miscibility with Water | See Test Method D 6999 |
Freezing | See Practice D 6929 |
Coating Ability and Water Resistance | 11-18 |
Storage Stability of Asphalt Emulsion | See Test Method D 6930 |
Examination of Residue | 19-26 |
Identification Test for Rapid Setting Cationic Emulsified Asphalt | 27-34 |
Identification of Cationic Slow Set Emulsions | See Test Method D 7402 |
Field Coating Test on Emulsified Asphalts | 35-40 |
Emulsified Asphalt/Job Aggregate Coating Test | 41-46 |
Density of Emulsified Asphalt | See Test Method D 6937 |
Residue by Low-Temperature Vacuum Distillation | See Test Method D 7403 |
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 4.1 This test method covers the procedure for determining the water content of an emulsified asphalt by reflux distillation using a water trap. 11.1 This test method is intended to aid in the identification of asphalt emulsions suitable for mixing with coarse graded calcareous aggregates. It can be applied to other aggregates. (See Note 2). 19.1 Tests for specific gravity, ash content, solubility in trichloroethylene, penetration, ductility and float test are suggested for examination of the emulsified asphalt residue obtained by distillation or evaporation (see Test Method D 6934 27.1 This practice covers a procedure for identifying rapid-setting cationic emulsified asphalts. Their inability to coat a specific silica sand distinguishes them from medium and slow setting cationic grades. 35.1 This is a quick field test method to ascertain the compatibility of an emulsified asphalt with the job aggregate. 41.1 This practice may be used to identify the adequacy of slow setting grade of emulsified asphalt to mix with and coat a dense and fine-graded job aggregate. It is a laboratory practice of screening emulsified asphalt candidates for mixing with and coating job aggregates and is not to be construed as a mix design test method.
Significance and Use
This test method measures the amount of water present in the emulsified asphalt, as distinguished from either bitumen or petroleum solvent.
Keywords
Asphalts; Cement; Classification (standards)--road/paving materials/applications; Coatings; Composition analysis--paving materials; Consistency--paving materials/applications; Demulsibility; Freezing and thawing; Miscibility; Particle charge test; Residue; Settlement; Sieve analysis; Stability; Storage stability; Viscometers--Saybolt-Furol; Viscosity--asphalts/bituminous materials; Water content; Weight; ICS Number Code 91.100.50 (Binders. Sealing materials); 93.080.20 (Road construction materials)
To find similar documents by ASTM Volume:
04.03 (Road and Paving Materials; Vehicle-Pavement Systems)
To find similar documents by classification:
91.100.50 (Binders. Sealing materials Including geomembranes, asphalts for buildings, etc.)
93.080.20 (Road construction materials Including asphalts, road pavements, etc.)
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Document Number
ASTM-D244-09
Revision Level
2009 EDITION
Status
Superseded
Modification Type
Revision
Publication Date
July 1, 2009
Document Type
Test Method
Page Count
9 pages
Committee Number
D04.42