ASTM-D378 Standard Test Methods for Rubber (Elastomeric) Conveyor Belting, Flat Type

ASTM-D378 - 2010 R16 EDITION - CURRENT
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:

Standard Test Methods for Rubber (Elastomeric) Conveyor Belting, Flat Type
ORDER

Price:

$69.00        


Want this as a site license?

Scope

1.1 These test methods (and references) cover the procedures for evaluating the physical properties of flat conveyor belting. Performance criteria for belting will not be detailed here, but can be found through the RMA (Rubber Manufacturers Association) Conveyor and Elevator Belt Handbook, ANSI (American National Standards Institute), various governmental authorities, and the International Organization for Standardization (ISO). Belting for conveying and elevating materials generally is designated and defined as follows:

1.1.1 Heavy Duty Conveyor—A heavy duty belt is defined as belting designed for bulk haulage of materials, such as stone, crushed rock, sand, metals ores, coal, wood chips, etc., and has a carcass strength (design) substantial enough to withstand conveyor system tensions of 160 PIW2 (pounds per inch of width) and above.

1.1.2 Light Duty Conveyor—A light duty belt is defined as belting designed for conveying a variety of lower weight (density) materials, packages, industrial and electronic goods, and food products. These belts often are shorter in length and width, with less overall thickness than heavy duty belting, and are generally used in conveyor systems with tensions less than 160 PIW.

1.1.3 General Description—Belting can have elastomeric coverings on one side, both sides, or neither side depending upon the specific application requirements. Belt coverings are comprised of various synthetic or natural rubber polymers, PVC, or other elastomeric materials, dependent upon application or customer requirements. The strength (load bearing) member(s) of most belting generally is a woven or interwoven carcass of synthetic or natural fibers, such as, but not limited to, polyester, nylon, polyaramide and cotton, as well as steel (cable/cord type or woven mesh).

1.2 This standard does not purport to address all of the application specific testing available or safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Significance and Use

4.1 Flat conveyor belts are used in many industrial applications in which they are subjected to a great variety of stresses and conditions. Service conditions can be calculated or measured. Design levels and test requirements are established by manufacturers, or end-users, or both. The tests (test methods) are used to measure the characteristics of conveyor belting as they relate to service conditions.

4.2 The tests outlined by these test methods are commonly applied by belt manufacturers to control the quality of their products.

4.3 Research and product development activities in flat belting involve extensive testing as outlined by these test methods.

4.4 In case of conflict between the provisions of these test methods and those of detailed specifications or test methods for a particular belt, the latter shall take precedence.

4.5 In case of conflict between the provisions of these test methods and those of detailed specifications or test methods for a particular belt, the latter shall take precedence.

Keywords

belting; elastomeric; RMA; rubber;; ICS Number Code 83.060 (Rubber)

To find similar documents by ASTM Volume:

09.02 (Rubber Products, Industrial - Specifications and Related Test Methods; Gaskets; Tires)

To find similar documents by classification:

83.060 (Rubber Raw rubber, see 83.040.10)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

 

Customers who bought this document also bought:

ASQ-Z1.4 & Z1.9
ASQ-Z1.4 & ASQ-Z1.9 Complete Set

NCCLS-C12
Definitions of Quantities and Conventions Related To Blood Ph& Gas Analysis

IPC-SM-840
Qualification and Performance Specifiation of Permanent Solder Mask and Flexible Cover Materials

Document Number

ASTM-D378-10(2016)

Revision Level

2010 R16 EDITION

Status

Current

Modification Type

Reapproval

Publication Date

Nov. 1, 2016

Document Type

Test Method

Page Count

13 pages

Committee Number

D11.31