Document Center is acquired by Nimonik

Scope

1.1 These test methods cover the measurement of average grain size and include the comparison procedure, the planimetric (or Jeffries) procedure, and the intercept procedures. These test methods may also be applied to nonmetallic materials with structures having appearances similar to those of the metallic structures shown in the comparison charts. These test methods apply chiefly to single phase grain structures but they can be applied to determine the average size of a particular type of grain structure in a multiphase or multiconstituent specimen.

1.2 These test methods are used to determine the average grain size of specimens with a unimodal distribution of grain areas, diameters, or intercept lengths. These distributions are approximately log normal. These test methods do not cover methods to characterize the nature of these distributions. Characterization of grain size in specimens with duplex grain size distributions is described in Test Methods E1181. Measurement of individual, very coarse grains in a fine grained matrix is described in Test Methods E930.

1.3 These test methods deal only with determination of planar grain size, that is, characterization of the two-dimensional grain sections revealed by the sectioning plane. Determination of spatial grain size, that is, measurement of the size of the three-dimensional grains in the specimen volume, is beyond the scope of these test methods.

1.4 These test methods describe techniques performed manually using either a standard series of graded chart images for the comparison method or simple templates for the manual counting methods. Utilization of semi-automatic digitizing tablets or automatic image analyzers to measure grain size is described in Test Methods E1382.

1.5 These test methods deal only with the recommended test methods and nothing in them should be construed as defining or establishing limits of acceptability or fitness of purpose of the materials tested.

1.6 The measured values are stated in SI units, which are regarded as standard. Equivalent inch-pound values, when listed, are in parentheses and may be approximate.

1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Significance and Use

These test methods cover procedures for estimating and rules for expressing the average grain size of all metals consisting entirely, or principally, of a single phase. The test methods may also be used for any structures having appearances similar to those of the metallic structures shown in the comparison charts. The three basic procedures for grain size estimation are:

Comparison Procedure—The comparison procedure does not require counting of either grains, intercepts, or intersections but, as the name suggests, involves comparison of the grain structure to a series of graded images, either in the form of a wall chart, clear plastic overlays, or an eyepiece reticle. There appears to be a general bias in that comparison grain size ratings claim that the grain size is somewhat coarser (¹/₂ to 1 G number lower) than it actually is (see X1.3.5). Repeatability and reproducibility of comparison chart ratings are generally ±1 grain size number.

Keywords

ALA grain size; anisotropy index; area fraction; ASTM grain size number; calibration; equiaxed grains; etchant; grain boundary; grains; grain size; intercept count; intercept length; intersection count; non-equiaxed grains; twin boundaries; ALA grain size; Anisotropy index; ASTM grain size number (G); Austenitic steel; Circular intercept procedures; Comparison techniques; Conversion units/factors; Copper; Copper alloy; Equiaxed grains; Ferritic stainless steel; General intercept procedures; Grain size; Intercept length/count; Linear intercept (Heyn) procedure; Metallographic analysis/inspection; Metals and metallic materials; Microscopic examination--metals/alloys; Nonequiaxed grains; Particle analysis--grain size; Photomicrography; Planimetric procedure; Single-circle (Hilliard) procedure; Structural metals/alloys; Three-circle (Abrams) procedure; ICS Number Code 49.025.05 (Ferrous alloys in general); 49.025.15 (Non-ferrous alloys in general)

To find similar documents by ASTM Volume:

03.01 (Metals -- Mechanical Testing; Elevated and Low-Temperature Tests; Metallography)

To find similar documents by classification:

19.120 (Particle size analysis. Sieving Including test sieves and porosimetry)

77.040.01 (Testing of metals in general)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.