Document Center is acquired by Nimonik

Document Center List of Standards on Refrigerants And Antifreezes

ICS Code 71.100.45

Return to ICS Index.

Up to Level 2:

• 71.100 (Products of the chemical industry Photographic chemicals, see 37.040.30 Raw materials for rubber and plastics, see 83.040 Paints and varnishes, see 87.040 Inks, see 87.080)

The following documents are a part of this series:

ASTM:

• ASTM-D1119 - Standard Test Method for Percent Ash Content of Engine Coolants
• ASTM-D1120 - Standard Test Method for Boiling Point of Engine Coolants
• ASTM-D1121 - Standard Test Method for Reserve Alkalinity of Engine Coolants and Antirusts
• ASTM-D1122 - Standard Test Method for Relative Density of Engine Coolant Concentrates and Engine Coolants By The Hydrometer
• ASTM-D1123 - Standard Test Methods for Water in Engine Coolant Concentrate by the Karl Fischer Reagent Method
• ASTM-D1176 - Standard Practice for Sampling and Preparing Aqueous Solutions of Engine Coolants or Antirusts for Testing Purposes
• ASTM-D1177 - Standard Test Method for Freezing Point of Aqueous Engine Coolants
• ASTM-D1287 - Standard Test Method for pH of Engine Coolants and Antirusts
• ASTM-D1384 - Standard Test Method for Corrosion Test for Engine Coolants in Glassware
• ASTM-D1881 - Standard Test Method for Foaming Tendencies of Engine Coolants in Glassware
• ASTM-D1882 - Standard Test Method for Effect of Cooling System Chemical Solutions on Organic Finishes for Automotive Vehicles
• ASTM-D2570 - Standard Test Method for Simulated Service Corrosion Testing of Engine Coolants
• ASTM-D2758 - Standard Test Method for Engine Coolants by Engine Dynamometer (Withdrawn 2022)
• ASTM-D2847 - Standard Practice for Testing Engine Coolants in Car and Light Truck Service
• ASTM-D2982 - Standard Test Methods for Detecting Glycol-Base Antifreeze in Used Lubricating Oils
• ASTM-D3147 - Standard Test Method for Testing Stop-Leak Additives for Engine Coolants
• ASTM-D3306 - Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service
• ASTM-D3585 - Standard Specification for ASTM Reference Fluid for Coolant Tests
• ASTM-D3634 - Standard Test Method for Trace Chloride Ion in Engine Coolants
• ASTM-D4656 - Standard Specification for Prediluted Aqueous Ethylene Glycol Base Engine Coolant (50 Volume % Minimum) for Automobiles and Light-Duty Service (Withdrawn 2000)
• ASTM-D4725 - Standard Terminology for Engine Coolants and Related Fluids
• ASTM-D4985 - Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA)
• ASTM-D5216 - Standard Specification for Propylene Glycol Base Engine Coolant for Automobile and Light-Duty Service (Withdrawn 2000)
• ASTM-D5223 - Standard Specification for Engine Coolant Grade Propylene Glycol (Withdrawn 2003)
• ASTM-D5345 - Standard Specification for Prediluted Aqueous Ethylene Glycol Base Low-Silicate Engine Coolant (50 Volume % Minimum) for Heavy-Duty Engines Requiring an Initial Charge of Supplemental Coolant Additive (SCA) (Withdrawn 2000)
• ASTM-D5666 - Standard Test Method for Rubber Chemical Antidegradants—Purity of p-Phenylenediamine (PPD) Antidegradants by High Performance Liquid Chromatography
• ASTM-D5752 - Standard Specification for Supplemental Coolant Additives (SCAs) for Use in Precharging Coolants for Heavy-Duty Engines
• ASTM-D5827 - Standard Test Method for Analysis of Engine Coolant for Chloride and Other Anions by Ion Chromatography
• ASTM-D5828 - Standard Test Method for Compatibility of Supplemental Coolant Additives (SCAs) and Engine Coolant Concentrates
• ASTM-D5931 - Standard Test Method for Density and Relative Density of Engine Coolant Concentrates and Aqueous Engine Coolants by Digital Density Meter
• ASTM-D6129 - Standard Test Method for Silicon in Engine Coolant Concentrates by Atomic Absorption Spectroscopy
• ASTM-D6130 - Standard Test Method for Determination of Silicon and Other Elements in Engine Coolant by Inductively Coupled Plasma-Atomic Emission Spectroscopy
• ASTM-D6210 - Standard Specification for Fully-Formulated Glycol Base Engine Coolant for Heavy-Duty Engines
• ASTM-D6211 - Standard Specification for Fully-Formulated Propylene-Glycol-Base Engine Coolant for Heavy-Duty Engines (Withdrawn 2003)
• ASTM-D6257 - Standard Specification for Prediluted Aqueous Propylene Glycol Base Engine Coolant (50 Volume % Minimum) for Automobile and Light-Duty Service (Withdrawn 2000)
• ASTM-D6471 - Standard Specification for Recycled Prediluted Aqueous Glycol Base Engine Coolant (50 Volume % Minimum) for Automobile and Light-Duty Service (Withdrawn 2019)
• ASTM-D6472 - Standard Specification for Recycled Glycol Base Engine Coolant Concentrate for Automobile and Light-Duty Service (Withdrawn 2019)
• ASTM-D6660 - Standard Test Method for Freezing Point of Aqueous Ethylene Glycol Base Engine Coolants by Automatic Phase Transition Method
• ASTM-D7304 - Standard Test Method for Determination of Denatonium Benzoate in Engine Coolant by HPLC
• ASTM-D7437 - Standard Test Method for Temperature and Hard Water Stability of Engine Coolants
• ASTM-D7517 - Standard Specification for Fully-Formulated 1,3 Propanediol (PDO) Base Engine Coolant for Heavy-Duty Engines
• ASTM-D7518 - Standard Specification for 1,3 Propanediol (PDO) Base Engine Coolant for Automobile and Light-Duty Service
• ASTM-D7640 - Standard Specification for Engine Coolant Grade Glycerin
• ASTM-D7713 - Standard Specification for Aqueous Engine Coolant Grade Glycol (53 % by Volume Nominal)
• ASTM-D7714 - Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service
• ASTM-D7715 - Standard Specification for Fully-Formulated Glycerin Base Engine Coolant for Heavy-Duty Engines
• ASTM-D7736 - Standard Test Method for Determination of Acids and Glycol Esters in Ethylene Glycol
• ASTM-D7820 - Standard Test Method for Engine Coolant Corrosion Protection Under Accelerated Thermal and Oxidizing Conditions Using a Rotating Pressure Vessel
• ASTM-D7840 - Standard Test Method for Foaming Tendencies of Non-Aqueous Engine Coolants in Glassware
• ASTM-D7896 - Standard Test Method for Thermal Conductivity, Thermal Diffusivity and Volumetric Heat Capacity of Engine Coolants and Related Fluids by Transient Hot Wire Liquid Thermal Conductivity Method
• ASTM-D7933 - Standard Test Method for Engine Coolant Stagnation in Flux-Brazed Aluminum Heat Exchangers
• ASTM-D7934 - Standard Test Method for Corrosion of Cast Aluminum Alloys in Non-Aqueous Engine Coolants Under Heat-Rejecting Conditions (Withdrawn 2023)
• ASTM-D7935 - Standard Test Method for Corrosion Test for Non-Aqueous Engine Coolants in Glassware
• ASTM-D8034 - Standard Test Method for Simulated Service Corrosion Testing of Non-Aqueous Engine Coolants
• ASTM-D8039 - Standard Specification for Heat Transfer Fluids (HTF) for Heating and Air Conditioning (HVAC) Systems
• ASTM-D8116 - Standard Specification for Fully-Formulated Non-Aqueous Engine Coolant for Heavy-Duty Engines (Withdrawn 2019)
• ASTM-E1177 - Standard Specification for Engine Coolant Grade Glycol

BSI:

• BS-5117-0 - Testing corrosion inhibiting, engine coolant concentrate ('antifreeze')
• BS-5117-1.1 - Testing corrosion inhibiting, engine coolant concentrate ('antifreeze'). Methods of test for determination of physical and chemical properties
• BS-5117-1.2 - Testing corrosion inhibiting, engine coolant concentrate ('antifreeze'). Methods of test for determination of physical and chemical properties
• BS-5117-1.3 - Testing corrosion inhibiting, engine coolant concentrate ('antifreeze'). Methods of test for determination of physical and chemicalproperties
• BS-5117-1.4 - Testing corrosion inhibiting, engine coolant concentrate ('antifreeze'). Methods of test for determination of physical and chemicalproperties
• BS-5117-1.5 - Testing corrosion inhibiting, engine coolant concentrate ('antifreeze'). Methods of test for determination of physical and chemical properties
• BS-5117-2.1 - Testing corrosion inhibiting, engine coolant concentrate ('antifreeze'). Methods of test for corrosion inhibition performance
• BS-5117-2.2 - Testing corrosion inhibiting, engine coolant concentrate ('antifreeze'). Methods of test for corrosion inhibition performance
• BS-5117-2.4 - Testing corrosion inhibiting, engine coolant concentrate ('antifreeze'). Methods of test for corrosion inhibition performance
• BS-5117-2.5 - Testing corrosion inhibiting, engine coolant concentrate ('antifreeze'). Methods of test for corrosion inhibition performance
• BS-5117-2.6 - Testing corrosion inhibiting, engine coolant concentrate ('antifreeze'). Methods of test for corrosion inhibition performance
• BS-6580 - Specification for corrosion inhibiting, engine coolant concentrate ('antifreeze')
• BS-EN-14624 - Performance of portable locating leak detectors and of fixed gas detectors for all refrigerants
• BS-EN-16811-1 - Winter service equipment and products. De-icing agents
• BS-EN-16811-2 - Winter service equipment and products. De-icing agents
• BS-ISO-17584 - Refrigerant properties
• BS-ISO-17584-TC - Tracked Changes. Refrigerant properties
• BS-ISO-817 - Refrigerants. Designation and safety classification
• PD-CEN-14739 - Scheme for carrying out a risk assessment for flammable refrigerants in case of household refrigerators and freezers
• PD-CEN-16811-3 - Winter maintenance equipment. De-icing agents
• PD-CEN-17608 - State of the art on the use of flammable refrigerant alternatives, in particular from class A3, in refrigeration, air conditioning and heat pump equipment

IEC:

• IEC-60335-2-104 - Household and similar electrical appliances - Safety - Part 2-104: Particular requirements for appliances to recover and/or recycle refrigerant from air conditioning and refrigeration equipment

ISO:

• ISO-17584 - Refrigerant properties
• ISO-817 - Refrigerants - Designation and safety classification
• ISO-817-AM1 - - Amendment 1
• ISO-817-AM2 - - Amendment 2

Other SDOs:

• DIN-EN-14624 - Performance of portable leak detectors and of room monitors for halogenated refrigerants
• EN-14624 - Performance of portable leak detectors and of room monitors for halogenated refrigerants
• EN-16811-1 - Winter service equipment and products - De-icing agents - Part 1: Sodium chloride - Requirements and test methods
• EN-16811-2 - Winter service equipment and products - De-icing agents - Part 2: Calcium chloride and Magnesium chloride - Requirements and test methods
• SIS-CEN-17608 - State of the art on the use of flammable refrigerant alternatives, in particular from class A3, in refrigeration, air conditioning and heat pump equipment
• SIS-CEN/TS-16811-3 - Winter service equipment and products - De-icing agents - Part 3: Other solid and liquid de-icing agents - Requirements and test methods
• SS-EN-1459-1 - Performance of portable locating leak detectors and of fixed gas detectors for all refrigerants
• SS-EN-14624 - Performance of portable locating leak detectors and of fixed gas detectors for all refrigerants
• SS-EN-16811-1 - Winter service equipment and products - De-icing agents - Part 1: Sodium chloride - Requirements and test methods
• SS-EN-16811-2 - Winter service equipment and products - De-icing agents - Part 2: Calcium chloride and Magnesium chloride - Requirements and test methods