ASTM-A369 › Historical Revision Information
Standard Specification for Carbon and Ferritic Alloy Steel Forged and Bored Pipe for High-Temperature Service
The following bibliographic material is provided to assist you with your purchasing decision:
This guide specifies standard specification for heavy-wall carbon and alloy steel pipe made from turned and bored forgings and is intended for high-temperature service. Heat and product analysis shall be conducted on several grades of ferritic steels, wherein the material shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, chromium, and molybdenum. The steel pipe shall conform to the required tensile properties like tensile strength, yield strength, and elongation. Required mechanical tests for the steel pipe include transverse or longitudinal tension test, flattening test, and bend test.
Scope
1.1 This specification covers heavy-wall carbon and alloy steel pipe (Note 1) made from turned and bored forgings and is intended for high-temperature service. Pipe ordered under this specification shall be suitable for bending and other forming operations and for fusion welding. Selection will depend on design, service conditions, mechanical properties and high-temperature characteristics.
Note 1—The use of the word “pipe” throughout the several sections of this specification is used in the broad sense and intended to mean pipe headers, or leads.
Note 2—The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.”
1.2 Several grades of ferritic steels are covered. Their compositions are given in Table 1.
1.3 Supplementary requirements (S1 to S6) of an optional nature are provided. These supplementary requirements call for additional tests to be made, and when desired shall be so stated in the order, together with the number of such tests required.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
TABLE 1 Chemical Requirements
| Grade | Composition, % | |||
|---|---|---|---|---|
| FPA | FPB | FP1 | FP2 | |
| Carbon | 0.25 max | 0.30 max | 0.10–0.20 | 0.10–0.20 |
| Manganese | 0.27–0.93 | 0.29–1.06 | 0.30–0.80 | 0.30–0.61 |
| Phosphorus, max | 0.035 | 0.035 | 0.025 | 0.025 |
| Sulfur, max | 0.035 | 0.035 | 0.025 | 0.025 |
| Silicon | 0.10 min | 0.10 min | 0.10–0.50 | 0.10–0.30 |
| Chromium | ... | ... | ... | 0.50–0.81 |
| Molybdenum | ... | ... | 0.44–0.65 | 0.44–0.65 |
| Grade | FP5 | FP9 | FP11 | FP12 |
| Carbon | 0.15 max | 0.15 max | 0.05–0.15 | 0.05–0.15 |
| Manganese | 0.30–0.60 | 0.30–0.60 | 0.30–0.60 | 0.30–0.61 |
| Phosphorus, max | 0.025 | 0.030 | 0.025 | 0.025 |
| Sulfur, max | 0.025 | 0.030 | 0.025 | 0.025 |
| Silicon | 0.50 max | 0.50–1.00 | 0.50–1.00 | 0.50 max |
| Chromium | 4.00–6.00 | 8.00–10.00 | 1.00–1.50 | 0.80–1.25 |
| Molybdenum | 0.45–0.65 | 0.90–1.10 | 0.44–0.65 | 0.44–0.65 |
| Grade | FP21 | FP22 | FP91 | FP92 |
| Carbon | 0.05–0.15 | 0.05–0.15 | 0.08–0.12 | 0.07–0.13 |
| Manganese | 0.30–0.60 | 0.30–0.60 | 0.30–0.60 | 0.30–0.60 |
| Phosphorus, max | 0.025 | 0.025 | 0.025 | 0.020 |
| Sulfur, max | 0.025 | 0.025 | 0.025 | 0.010 |
| Silicon | 0.50 max | 0.50 max | 0.20–0.50 | 0.50 max |
| Chromium | 2.65–3.35 | 1.90–2.60 | 8.00–9.50 | 8.50–9.50 |
| Molybdenum | 0.80–1.06 | 0.87–1.13 | 0.85–1.05 | 0.30–0.60 |
| Others: | W 1.50–2.00 | |||
| Ni 0.40 max | V 0.15–0.25 | |||
| V 0.18–0.25 | Cb 0.04–0.09 | |||
| Cb 0.06–0.10 | N 0.030–0.070 | |||
| N 0.03–0.07 | Ni 0.40 max | |||
| Al 0.02 max | Al 0.02 max | |||
| Ti 0.01 max | Ti 0.01 max | |||
| Zr 0.01 max | Zr 0.01 max | |||
| B 0.001–0.006 | ||||
Keywords
Alloy steel forgings--specifications; Alloy steel pipe--specifications; Carbon steel pipe--specifications; Ferritic steel pipe--specifications; High-temperature service applications--steel pipe; ICS Number Code 23.040.10 (Iron and steel pipes)
To find similar documents by ASTM Volume:
01.01 (Steel--Piping, Tubing, Fittings)
To find similar documents by classification:
23.040.10 (Iron and steel pipes Steel pipes and tubes for specific use, see 77.140.75)
This document comes with our free Notification Service, good for the life of the document.
This document is available in either Paper or PDF format.
Document Number
ASTM-A369/A369M-11
Revision Level
2011 EDITION
Status
Superseded
Modification Type
Revision
Publication Date
Nov. 1, 2011
Document Type
Specification
Page Count
5 pages
Committee Number
A01.10