ASTM-F568M Standard Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners (Withdrawn 2012)

ASTM-F568M - 2007 EDITION - CANCELLED
Show Complete Document History

Document Center Inc. is an authorized dealer of ASTM standards.
The following bibliographic material is provided to assist you with your purchasing decision:


This specification covers the chemical and mechanical requirements for nine property classes (Property Class 4.6, 4.8, 5.8, 8.8, 8.8.3, 9.8, 10.9, 10.9.3, and 12.9) of carbon and alloy steel externally threaded fasteners in nominal thread diameters M1.6 through M100 suited for use in general engineering applications. It does not cover the dimensional requirements for fasteners of any property class. The steel used to manufacture bolts, screws, and studs that are covered here shall be made by the open-hearth, basic-oxygen, or electric-furnace process. The fasteners shall adhere to specified values of elemental chemical compositions, which shall be examined by heat and product analyses. Each property class shall also conform to individually specified values of the following mechanical properties: proof load, wedge and axial tensile strengths, yield strength, elongation, reduction of area, surface hardness, Rockwell hardness, Vickers hardness, and stress area.

Scope

1.1 This specification covers chemical and mechanical requirements for nine property classes of carbon and alloy steel externally threaded metric fasteners in nominal thread diameters M1.6 through M100 suited for use in general engineering applications.

1.2 This specification does not cover dimensional requirements for fasteners of any property class. When referencing this specification for procurement purposes, it is mandatory that size, type, style, and any special dimensions of the product be additionally specified.

1.2.1 In case of any conflict in requirements, the requirements of the individual product specification shall take precedence over those of this general specification.

1.2.2 The purchaser may specify additional requirements which do not negate any of the provisions of this general specification or of the individual product specification. Such additional requirements, the acceptance of which are subject to negotiation with the supplier, must be included in the order information (see Section 3).

1.3 Requirements for seven of the nine property classes, 4.6, 4.8, 5.8, 8.8, 9.8, 10.9, and 12.9, are essentially identical with requirements given for these classes in ISO 898-1. The other two, 8.8.3 and 10.9.3, are not recognized in ISO standards.

1.4 Classes 8.8.3 and 10.9.3 bolts, screws, and studs have atmospheric corrosion resistance and weathering characteristics comparable to those of the steels covered in Specification A 588/A 588M. The atmospheric corrosion resistance of these steels is substantially better than that of carbon steel with or without copper addition. See 5.2. When properly exposed to the atmosphere, these steels can be used bare (uncoated) for many applications.

1.5 When agreed on by the purchaser, Class 5.8 fasteners may be supplied when either Classes 4.6 or 4.8 are ordered; Class 4.8 may be supplied when Class 4.6 is ordered; Class 8.8.3 may be supplied when Class 8.8 is ordered; and Class 10.9.3 may be supplied when Class 10.9 is ordered.

1.6 The product size range for which each property class is applicable is given in Table 1 and Table 2 on chemical composition requirements, and the mechanical requirements table (see Table 3).

1.7 Appendix X1 gives conversion guidance to assist designers and purchasers in the selection of a suitable property class.

1.8 Appendix X2 explains the significance of the property class designation numerals.

Keywords

alloy steel; bolts; carbon steel; metric; screws; steel; structural; weathering steel; Alloy steel bolting materials specifications; Carbon steel bolting materials specifications; Externally threaded articles/fasteners/rods; Fasteners (metal) specifications; Metric threaded bolting components; Steel fasteners specifications; ICS Number Code 21.060.10 (Bolts, screws, studs)

To find similar documents by ASTM Volume:

01.08 (Fasteners; Rolling Element Bearings)

To find similar documents by classification:

21.060.10 (Bolts, screws, studs)

This document comes with our free Notification Service, good for the life of the document.

This document is available in either Paper or PDF format.

 

Customers who bought this document also bought:

ASTM-A1008
Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable

ASTM-A1011
Standard Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength

ASTM-D2240
Standard Test Method for Rubber Property—Durometer Hardness

Document Number

ASTM-F568M-07

Revision Level

2007 EDITION

Status

Cancelled

Modification Type

Withdrawn

Publication Date

Dec. 1, 2007

Document Type

Specification

Page Count

9 pages

Committee Number

F16.02